Loewe Connect ID 46 Operating Instructions Manual page 27

Connect ID 32-46
Operating instructions
Initial installation
Setting options for the satellite system
(other communal installation):
Select single
INITIAL INSTALLATION (DVB-S)
satellite
Select single satellite
Astra1 19,2°E
Hot Bird 13°E
Astra2 28,2°E
Astra3 23,5°E
Atlantic Bird1 12,5 °W
Atlantic Bird2 8°W
Atlantic Bird3 5°W
Eurobird1 28,5°E
Eurobird 9A 9°E
Eutelsat W2 16°E
Eutelsat W3A 7°E
Eutelsat W4 36°E
Proceed
OK
Select satellite,
OK Proceed.
Network
INITIAL INSTALLATION
Network selection
selection
other network
CanalDigitaal
Proceed
OK
Select network.
If several networks are available over DVB-S, you
can decide which network you want to receive
your channels from.
OK Proceed.
LNB
INITIAL INSTALLATION (DVB-S)
settings
LNB frequency
Supply voltage
Proceed
OK
Select and adapt settings.
LNC Normally, you do not need to change the values for high
and low band, unless the LNC (LNB) of your satellite
frequency
system uses a different oscillator frequency (important
for the frequency display).
If your set is connected to a single-cable system without
Supply voltage
external voltage supply, you can connect the antenna
supply (13V or 18V / max. 500mA).
OK Proceed.
(with Setting options for all types of reception on
page 28).
- 27 -
Hellas Sat2 39°E
OK
Hispasat 30°W
Intelsat10 02 1°W
Intelsat901 18°W
Nilesat 7°W
Pan Am Sat 43°W
Sirius2/3 5°E
Telekom2C 5°W
Telekom2D 8°W
Telestar12 12,5°W
Thor2/3 0,8°W
Türksat 42°E
OK
Back
9750 MHz
off
Back
Setting options for DVB-S reception (continued):
Test reception
FIRST INSTALLATION WIZARD
You should now receive a picture and sound from the following satellite:
ASTRA1 19,2°E
If not, please align your dish correctly. If however it is correctly aligned and
you have an older version you can proceed with
Proceed
OK
After you have made the previous settings, you should
receive picture and sound of the selected satellites (only
possible for Astra1 and HOTBIRD).
OK Proceed.
Settings
INITIAL INSTALLATION (ASTRA1 19,2°E)
HD station preferred
Scrambled stations
Search method
Symbol rate 1 (DVB-S)
Symbol rate 2 (DVB-S)
Proceed
OK
Select and adapt settings.
If several satellites are received, the following settings
must be made for every satellite. The type of settings
available may differ depending on the selected satellite
or network.
HD station Here you can choose whether high resolution channels
preferred should be prioritised in the channel overview.
➠ The menu item is only available for certain receiving
networks.
Encrypted You can state whether coded stations are to be searched
stations for in the search/update.
scrambled stations. However, these stations can only be
received in connection with a CA module and the
appropriate Smart Card.
described on page 63.
If a CA module with a SmartCard is already plugged in
for the station search, all the stations which this module
can descramble are also saved when no is preset.
Search If you want to run the station search independently of
method the channel grid, select frequency search for the search
method.
The symbol rates are specified by the satellite provider
Symbol rates
and do not normally need to be changed.
OK Proceed.
(with Setting options for all types of reception on
page 28).
C/N Level
.
OK
Back
yes
yes
no
OK
Channel search
27500
22000
Back
Select yes to save all found
Handling of the CA module is