Loewe Connect ID 46 Operating Instructions Manual page 26

Connect ID 32-46
Operating instructions
Initial installation
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
Settings
INITIAL INSTALLATION (DVB-S)
DiSEqC
Repeat rate
Control voltage 13/18V
multiswitch
22kHz signal
Toneburst
Proceed
OK
Select and adapt settings for the DiSEqC
multiswitch.
Repeat rate The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
Control
The control voltage controls the switching of the
voltage polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g. control of single LNBs via
DiSEqC multiswitch).
22kHz signal
The 22kHz signal controls the switching between high
and low band in the Band setting. The Position setting
controls the selection of the satellites in non-DiSEqC
capable components.
Toneburst The Toneburst controls the selection of the satellites in
non-DiSEqC but toneburst capable components with
the Position and Option settings.
OK Proceed
Satellite
INITIAL INSTALLATION (DVB-S)
selection
Satellite selection
Satellite 1
Satellite 2
Satellite 3
Satellite 4
Proceed
OK
Select Satellite 1 ... Satellite 4,
select satellites from list,
OK Proceed.
Network
INITIAL INSTALLATION
selection
Network selection
other network
CanalDigitaal
Proceed
OK
Select network.
If several networks are available over DVB-S, you
can decide which network you want to receive
your channels from.
OK Proceed.
LNB
INITIAL INSTALLATION (DVB-S)
LNB frequencies
frequencies
ASTRA1 19,2°E Low band
ASTRA1 19,2°E High band
Hot Bird 13°E Low band
Hot Bird 13°E High band
Eutelsat W2 16°E Low band
Eutelsat W2 16°E High band
Proceed
OK
Set LNB frequencies.
You do not normally need to change the values.
OK Proceed.
(with Setting options for DVB-S reception (contin-
ued) on page 27).
none 1 2
on
Band
off
Back
Astra1 19,2°E ...
Hot Bird 13°E
Eutelsat W2 16°E
none
Back
OK
Back
9750 MHz
10600 MHz
9750 MHz
10600 MHz
9750 MHz
10600 MHz
Back
- 26 -
Setting options for the satellite system
(DiSEqC one cable communal system):
DiSEqC one
cable
communal
system
OK Proceed.
Satellite
selection
OK Proceed.
Network
selection
OK Proceed.
LNB
frequencies
OK Proceed.
Manual
registration
(for socket
ANT SAT)
Transmission Select the desired transmission channel and the corre-
channel/ sponding transmission frequency.
frequency
PIN protection If your system is designed for it, it is possible to protect
your used transmission data from use by other subscrib-
ers with a PIN.
OK Proceed.
INITIAL INSTALLATION (DVB-S)
Select DiSEqC single cable communal installation
DELTA SUM-514
DELTA SUM-516
DELTA SUM-518
DELTA SUM-918
DELTA SUM-928
KATHREIN EXR-551
KATHREIN EXR-552
KATHREIN EXR-501
Proceed
OK
Select DiSEqC single cable communal installation.
INITIAL INSTALLATION (DVB-S)
Satellite selection
Satellite 1 Astra1 19,2°E
Proceed Back
OK
Select satellites from list,
INITIAL INSTALLATION
Network selection
other network
CanalDigitaal
Proceed Back
OK
Select network.
If several networks are available over DVB-S, you
can decide which network you want to receive
your channels from.
INITIAL INSTALLATION (DVB-S)
LNB frequencies
Low band 9750 MHz
High band 10600 MHz
Proceed Back
OK
Set LNB frequencies.
Normally, you do not need to change the values
for high and low band, unless the LNC (LNB) of
your satellite system uses a different oscillator
frequency (important for the frequency display).
INITIAL INSTALLATION (DVB-S)
Manual registration (for socket ANT SAT)
Transmission channel 1
Transmission frequency 1284
PIN protection no
Define/change PIN 0000
Proceed
OK
Select and adjust settings for the DiSEqC single
cable communal installation.
(with Setting options for DVB-S reception (contin-
ued) on page 27).
OK
...
OK
2 3 4 5 6
OK