Sony SRW-1 Operation Manual page 99

dB
SDI SDI SDI SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP EMP EMP EMP
EE
L R L R L R L R L R L R
1 2 3 4 5 6
STBY OFF
TCG
01 01 51
H M
12.2V REMAIN CH.COND
- - -
The S in S23PsF indicates that SR Motion is enabled.
(SELECT FPS is set to "ON" for Slow Shutter.) The
23PsF indicates that FPS FORMAT is set to 23.98PsF.
(23PsF) indicates that the target frame frequency is
23.98PsF.
To make the timecode continuous
Make the following settings in the TC Setup menu.
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset) or RGN (Regen), both
are available.
REGEN SOURCE: INT L (Internal LTC) (following
the timecode recorded on the tape)
For details on the TC Setup menu, see 4-2 "TC Setup
Menu" (page 46).
3
Select the camera in this unit's menu system.
1 Press the menu selection button "VIDEO" on the
control panel.
The VIDEO Setup menu appears.
2 Rotate the SELECT/ENTER dial to select
"VIDEO I/O" and press the dial.
A submenu window opens.
3 Rotate the SELECT/ENTER dial to select "VA
INPUT" in the submenu window.
A setting window opens.
4 Rotate the SELECT/ENTER dial to select
"CAM(Optical)" and press the dial.
5 Press the BACK button.
6 Rotate the SELECT/ENTER dial to select "CAM
TYPE".
A setting window opens.
7 Rotate the SELECT/ENTER dial to select "F950"
and press the dial.
4
On the camera, set the number of frames to be stored.
Set the item "LFE" in the menu of the HDC-F950 to
"ON" and set the number of frames to store.
For details on operation of the HDC-F950, refer to the
HDC-F950 Operation Manual.
SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R
7 8 9 10 11 12
SRW-1:CAM
KEYINHI
RECINHI
11
S F
IN: --:--:--:--
1080
LOCAL
S23PSF
EE
(23PsF)
17:11
444SQ
Note
Before shooting
Every time you change the LFE and stored frames settings
on the HDC-F950, be sure to power the camera off and on
again, open the iris, and shoot a test image of a bright
subject. If you do not make a test shot, frames will not be
stored correctly and the camera will not operate correctly.
5
Start shooting.
1 Check the timecode of the current position (make
a memo), so that you will be able to rewind after
shooting.
2 Set the number of frames to be stored by the
camera.
3 Start recording.
4 Stop recording.
6
Conduct a review.
1 Rewind to the timecode position that you noted in
step 4 1.
2 Set Select FPS in the SYSTEM >FORMAT menu
to "OFF" to set the playback timecode to 24
frames/sec (the target frame frequency to
23.98PsF).
3 Press the SET button to switch the format set on
this unit and the F23/F35.
4 Press the PLAY button to start playback.
You can check the slow or quick motion effect at the
target frame frequency of 23.98PsF. The timecode
advances from 0 to 23 frames per second. You can also
review the recording by using simple playback without
checking the slow or quick motion effect.
For more information about simple playback, see "To
perform simple playback without checking motion
effects" (page 87).
Notes
• Audio cannot be recorded normally when SR Motion is
used for shooting.
• When the number of frames stored by the camera is set
to a value larger than one, recording to the tape proceeds
in starts and stops, because data is recorded only when a
certain amount has been accumulated in the unit's
internal memory.
• In Slow Shutter shooting, it is not possible to vary the
number of frames stored during recording.
99
7-4 Slow Shutter Function