Sony SRW-1 Operation Manual page 93

The format of the unit is switched, and
"S59P(23PsF)" appears in the display (for about
30 seconds).
dB
SDI SDI SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP EMP EMP
EE
L R L R L R L R L R
1 2 3 4 5
STBY OFF
TCG
01 01
H
12.2V REMAIN CH.COND
- - -
The S in S59P indicates that SR Motion is enabled.
(SELECT FPS is set to "VTR", and the Interval
Frame function is used.) The 59P indicates that
FPS FORMAT is set to 59.94P. (23PsF) indicates
that the target frame frequency is 23.98PsF.
To make the timecode continuous
Make the following settings in the TC Setup menu.
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset) or RGN (Regen), both
are available.
REGEN SOURCE: INT L (Internal LTC) (following
the timecode recorded on the tape)
For details on the TC Setup menu, see 4-2 "TC Setup
Menu" (page 46).
3
Set the frame interval (FRM).
1 Exit the menu, and press the SELECT/ENTER
dial with the FUNC button held down in the
HOME screen.
The popup window displays the current frame
interval (FRM), the current number of frames
(FPS), and the playback speed.
dB
ANA ANA SDI SDI
0
-10
-20
SR Motion Recording
-30
-60
EMP EMP EMP EMP
SYSTEM
PB
L R L R L R L R
SEL-FPS : 59.94P
1 2 3 4
MODE
SIGNAL
OOOO PLAY LOCK
MEMORY
TCG LTC INTRP
FRM
00 00
FPS
H [ x 2.400 ]
INDLY: LTC VITC AU
SYS : 1080 S59P(23PsF) 4:2:2
FRM : 8 / 8 F R M ( M O D E : V T R )
MEM : 2 1 %
Playback speed
(times normal playback speed)
Number of frames (FPS)
SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R
6 7 8 9 10 11 12
SRW-1:CAM
KEYINHI
RECINHI
51 11
M S F
IN: --:--:--:--
1080
LOCAL
S59P
EE
(23PsF)
17:11
444SQ
SDI SDI SDI SDI SDI SDI A/E A/E
EMP EMP EMP EMP EMP EMP EMP EMP
: 23.98PsF
L R L R L R L R L R L R L R L R
5 6 7 8 9 10 11 12
: VTR
: 6 FRM
*SRW-1
: 21 %
DF EXT-LK KEYINHI
6
RECINHI
FRM
00 00
10.000
FPS
M S F
IN: --:--:--:--
50min
12.8V
Frame Interval (FRM)
When you press the SELECT/ENTER dial with
the FUNC button held down and do not perform
any operation for three seconds, the screen returns
to the previous state. When you press the
SELECT/ENTER dial with the FUNC button held
down and press the SELECT/ENTER dial again
with the FUNC button held down, the following
screen appears. This screen remains on the display
even if you do not perform any operation for three
seconds or more.
SR Motion Recording
dB
ANA ANA SDI SDI SDI
0
-10
SYSTEM : 23.98PsF
-20
SEL-FPS : 59.94P
-30
MODE : VTR
-60
SIGNAL : 6 FRM
EMP EMP EMP EMP EMP
MEMORY : 41 %
PB
L R L R L R L R L R
1 2 3 4 5
OO1O REC
TCG
00 02
H
SYS : 1080 S59P(23PsF) 4:2:2
FRM : 8 / 8 F R M ( M O D E : V T R )
MEM : 4 1 %
2 Rotate the SELECT/ENTER dial or ADJUST dial
to select the value of FRM.
The values of FPS and playback speed are
displayed according to the value of FRM.
Note
In the Interval Frame function, the number of frames
cannot be set at steps of 1 FPS, which is different from
the Select FPS function. For example, when you shoot
using a camera of 60P format at 1FRM intervals, the
number of frames is 60 FPS. However, since the next
interval which can be set is 2 FRM, the number of
frames becomes 30 FPS.
4
Start shooting.
1 Check the timecode of the current position (make
a memo), so that you will be able to rewind after
shooting.
2 Set the frame frequency (FRM value).
3 Start recording. During recording, change the
FRM value as required by rotating the SELECT/
ENTER dial.
4 Stop recording.
5
Conduct a review.
1 Rewind to the timecode position that you noted in
step 4 1.
2 Set Select FPS in the SYSTEM >FORMAT menu
to "OFF" to set the playback timecode to 24
frames/sec (the target frame frequency to
23.98PsF).
3 Press the SET button to switch the format.
SDI SDI SDI SDI SDI A/E A/E
FRM
6
FRM
FPS
10.000
FPS
EMP EMP EMP EMP EMP EMP EMP
[ x 2.400 ]
L R L R L R L R L R L R L R
6 7 8 9 10 11 12
SRW-1
KEYINHI
RECINHI
11 20
M S F
50min
12.8V
7-3 Interval Frame Function
93