Sony SRW-1 Operation Manual page 47

Item
TCG SET(MAIN) DF/NDF
Timecode generator (Valid only when the
settings for the main frame frequency of
timecode this system is 29.97
Hz)
UBG SOURCE
12H/24H
OTHERS(MAIN) TC OUT
Other settings related
to main timecode
RT REC
RT SET
RT SRC
VITC REC
LTC Delay
VITC Delay
Settings
Selects the frame count mode.
DF [Drop Frm]: Drop-frame mode
NDF [Non Drop Frm]: Non-drop frame mode
Note
These settings are valid only when the TCG MODE item is set to PRST.
Selects the source timecode of user bits.
TCG [TCG Source]: The same source as the source of the internal timecode
generator
INT [Internal]: Timecode generated by the timecode generator. Arbitrary user
bits settings (see page 69) are possible, regardless of the TCG setting.
Selects the CTL display mode.
12H [+/–12H]: 12-hour display mode
24H [24H]: 24-hour display mode
Note
When +/–12H display is selected, the tens digit of the hours value is dropped for
values less than 10.
Selects the timecode output from the TC OUT connector.
AUTO [Auto]: During playback, timecode read by the internal timecode reader.
During recording (including E-E mode), timecode generated by the timecode
generator is output, delayed by 1 frame. (This maintains synchronization
with the output video).
TCG [TCG]: Timecode generated by the timecode generator is output, delayed
by 1 frame. (This maintains synchronization with the output video).
THRU [Through]: Through output of timecode input to the TC IN connector
TCG (No Delay): Timecode generated by the timecode generator is output, with
no delay. (The timecode is out of synchronization with the output video,
being 1 frame in advance of the video.) Select this setting when you want to
synchronize other devices, using the timecode generator of this unit as the
master.
Selects whether or not to record the real time in user bits (see page 69).
OFF [Off]: Do not record.
VITC [VITC UB]: Record in VITC.
V+L [VITC UB+LTC UB]: Record in VITC and LTC.
LTC [LTC UB]: Record in LTC.
Sets the real time.
Selects the real time to record in user bits.
RTC [RTC]: Record real time set in RT REC and RT SET. (Select this normally.)
DATE [DATE]: Record real time of the internal clock (real time shown as status
information in the control panel display). This does not guarantee that frame
count advances continuously.
Selects the delay for VITC user bits, for use in tape dubbing.
TCG [TCG]: User bits are delayed by one frame in both VITC and LTC (same as
previous versions).
VIN [Video IN]: VITC user bits are not delayed. (LTC user bits are delayed by one
frame.)
Sets the phase difference between the timecode generator and the LTC input
from the TC IN connector.
0 [NO Delay]: Same timing
+1F [+1F Delay]: The generator is delayed by one frame
+2F [+2F Delay]: The generator is delayed by two frames.
+3F [+3F Delay]: The generator is delayed by three frames.
+4F [+4F Delay]: The generator is delayed by four frames.
+5F [+5F Delay]: The generator is delayed by five frames.
Sets the phase difference between the timecode generator and the LTC/VITC
timecode of the video signal input from the HD SDI IN A/B connectors.
0 [NO Delay]: Same timing
+1F [+1F Delay]: The generator is delayed by one frame
+2F [+2F Delay]: The generator is delayed by two frames.
+3F [+3F Delay]: The generator is delayed by three frames.
+4F [+4F Delay]: The generator is delayed by four frames.
+5F [+5F Delay]: The generator is delayed by five frames.
47
4-2 TC Setup Menu