Monitor Lut Function - Sony SRW-1 Operation Manual

Monitor LUT Function

The Monitor LUT (Look Up Table) function is available
when the SRW-1 is combined with the SRPC-1 and is in
separate operation with the F23/F35 camera. If you are
using S-Log or another gamma curve at the shooting site,
you can use a LUT file to convert the shooting data to 4:2:2
monitor output for viewing on a monitor with normal ITU-
BT709 gamma (only when shooting in the RGB 4:4:4
format).
For details about S-Log and gamma curves, refer to the
F23/F35 Operation Manual.
LUT files
LUT files are loaded from a "Memory Stick" (/MSSONY/
PRO/VTR/SRW-1/LUT) into the LUT banks of this unit.
You can load up to four LUT files into Bank0 to Bank3.
Once they have been loaded into banks, the files are
retained even after this unit is powered off. To select a file,
select the bank where it is stored. The content of the file is
transferred to the 4:4:4/4:2:2 conversion module of the
SRPC-1 and used for 4:4:4/4:2:2 conversion.
Use LUT files with extension ".lut" on this unit. Change
the extension, if it is not ".lut".
For the format of LUT files that can be loaded by this unit,
see "LUT file format" (page 122)).
Use the CvpFileEditor
For details about CvpFileEditor, refer to the F23/F35
Operation Manual.
1) CvpFileEditor is a trademark of Sony Corporation.
To load a LUT file into a bank
Proceed as follows to load a LUT file from a "Memory
Stick" into one of the banks of this unit.
1
Insert a "Memory Stick" containing the LUT file into
the Memory Stick slot.
2
In the VIDEO Setup menu, select LUT(MON) >LUT
MODE.
L o a d L U T
27.628/1919.43 MB Free: 85% used
<\MSSONY\PRO\VTR\SRW-1\LUT\>
< DIR > .
< DIR > ..
15,488 BANK0_709ToCineon...
15,656 BANK1_SlogHG2_Lus...
15,239 BANK2__031815.lut
16,175 BANK3_SlogTo709_L...
File Name .
File Size < Directory >
Data/Time 2008/03/14
Attribute
S T B Y O F F
SR W- 1
120
Monitor LUT Function
TM 1)
software to create LUT files.
[ *.LUT]
03:17
0 0 : 0 0 : 0 0 : 0 0
T C G
3
Rotate the SELECT/ENTER dial to select the bank
into which to load the LUT file, and then press the dial.
The LUT LOAD menu appears, with a list of the LUT
files in the "Memory Stick".
4
Rotate the SELECT/ENTER dial to select a LUT file,
and then press the dial.
Simple I/O curves of the selected LUT file appear.
5
Rotate the SELECT/ENTER dial to select OK, and
then press the dial.
The selected LUT file is loaded into the current bank.
To check LUT files in the banks
You can check LUT files in the banks, change file
selection, and delete unneeded LUT files from the banks.
For the procedure to load a LUT file into a bank, see "To
load a LUT file into a bank" (page 120)).
1
In the VIDEO Setup menu, select LUT(MON) >LUT
STATUS.
The currently selected bank is displayed in yellow.
L U T S t a t u s
BANK0:709ToCineon.lut
BANK1:SlogHG2_Lustre.lut
BANK2:DEFAULT
BANK3:SlogTo709_Lustre.lut
[ENTER] :SHOW DETAIL
[FUNC]+[ENTER]:BANK CLEAR
LUT Status
S T O P
S R W- 1
2
Press the SELECT/ENTER dial.
A simple I/O curve of the LUT file in the currently
selected bank appear.
L U T S t a t u s
BANK0:709ToCineon.lut
BANK1:SlogHG2_Lustre.lut
BANK2:DEFAULT
BANK3:SlogTo709_Lustre.lut
Press[FUNC]+[ENTER] to Select.
S T B Y O F F
S R W- 1
To select another LUT file
Rotate the SELECT/ENTER dial to select another bank,
and press the dial with the FUNC button held down.
The other bank is selected (displayed in yellow).
00:00:00:00
T CG
00:00:00:00
T CG