Sony SRW-1 Operation Manual page 86

dB
SDI SDI SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP EMP EMP
EE
L R L R L R L R L R
1 2 3 4 5
STBY OFF
TCG
01 01
H
12.2V REMAIN CH.COND
- - -
The S in S59P indicates that SR Motion is enabled
(SELECT FPS is set to "ON"). The 59P indicates that
FPS FORMAT is set to 59.94P. (23PsF) indicates that
the target frame frequency setting is 23.98PsF.
To make the timecode continuous
Make the following settings in the TC Setup menu.
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset) or RGN (Regen), both
are available.
REGEN SOURCE: INT L (Internal LTC) (following
the timecode recorded on the tape)
For details on the TC Setup menu, see 4-2 "TC Setup
Menu" (page 46).
3
Set the number of frames to shoot.
You can also set the number of frames to shoot on the
camera. Refer to the operation manual supplied with
the F23/F35 for information about how to make this
setting on the camera side.
1 While holding the FUNC button down, press the
SELECT/ENTER dial.
2 Rotate the SELECT/ENTER dial to set the number
of frames to shoot. (The setting range is 1 to 60
FPS if you are using the F23, or 1 to 50 FPS if you
are using the F35.)
dB
SDI SDI SDI
0
-10
-20
SR Motion Recording
-30
-60
EMP EMP EMP
SYSTEM
EE
L R L R L R
SEL-FPS : 59.94P
1 2 3
MODE
SIGNAL
STBY OFF
MEMORY
TCG
01 01
H
12.2V REMAIN
- - -
Playback speed
86
7-2 Select FPS Function
SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R
6 7 8 9 10 11 12
SRW-1:CAM
KEYINHI
RECINHI
51 11
M S F
IN: --:--:--:--
1080
LOCAL
S59P
EE
(23PsF)
17:11
444SQ
SDI SDI SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP EMP EMP
: 23.98PsF
L R L R L R L R L R L R L R L R L R
4 5 6 7 8 9 10 11 12
: ON
: 0 FPS
SRW-1:CAM
: ---
KEYINHI
48
RECINHI
51 11
FPS
[ x 0.500 ] M S F
IN: --:--:--:--
1080
LOCAL
CH.COND
S59P
EE
(23PsF)
17:11
444SQ
Number of frames (FPS)
To confirm the new setting, press the SELECT/
ENTER dial or leave it unrotated for three seconds.
The display returns to the original screen.
A screen like the one shown below appears if you hold
down the FUNC button and press the SELECT/
ENTER dial again while the above screen is displayed.
This new screen remains even if three seconds pass
with no operation. While this screen is visible, you can
check the setting that specifies the number of frames to
shoot. To do so, hold down the FUNC button and press
the HOME button. The signal format display at the
bottom of the screen changes into the SR Motion
display, allowing you to check the number of frames
setting.
SR Motion Recording
dB
SDI SDI SDI SDI SDI SDI
0
-10
SYSTEM : 23.98PsF
-20
SEL-FPS : 59.94P
-30
MODE : ON
-60
SIGNAL : 0 FPS
EMP EMP EMP EMP EMP EMP
MEMORY : ---
EE
L R L R L R L R L R L R
1 2 3 4 5 6
OO3O CASS OUT
TCG
00 17 55
H M
12.3V REMAIN CH.COND
- - -
You can also change the number of frames as you are
shooting (Ramp function). For details, see 7-2-3
"Using the Ramp Function" (page 88).
4
Start shooting.
1 Check the timecode of the current position (make
a memo), so that you will be able to rewind after
shooting.
2 Set the number of frames to be shot by the camera
(FPS value).
3 Start recording. During recording, change the FPS
value as required by rotating the SELECT/ENTER
dial.
4 Stop recording.
5
Conduct a review.
1 Rewind to the timecode position that you noted in
step 4 1.
2 Set Select FPS in the SYSTEM >FORMAT menu
to "OFF" to set the playback timecode to 24
frames/sec (the target frame frequency to
23.98PsF).
3 Press the SET button to switch the format set on
this unit and the F23/F35.
4 Press the PLAY button to start playback.
You can check the slow or quick motion effect at the
target frame frequency of 23.98PsF. The timecode
SDI SDI SDI SDI SDI SDI
48
FPS
EMP EMP EMP EMP EMP EMP
[ x 0.500 ]
L R L R L R L R L R L R
7 8 9 10 11 12
SRW-1:CAM
KEYINHI
RECINHI
16
S F
1080
LOCAL
S59P
EE
(23PsF)
10:11
422