Sony SRW-1 Operation Manual page 63

4
Select the desired value by rotating and pressing the
SELECT/ENTER dial.
This returns you to the submenu window, which is
activated again.
5
Repeat steps 3 and 4 to set the FRAME and SIGNAL
items.
6
In the submenu window, select [SET].
7
Make sure of the format, move the cursor to "OK", and
then press the SELECT/ENTER dial.
A message appears to inform you that the format has
been selected, and you return to the HOME screen.
To set with OTHERS
dB ANLG ANLG SDI SDI SDI SDI SDI SDI SDI SDI A/E
0
-10
HOME
-20
-30
-60
EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP
TC
PB
L R L R L R L R L R L R L R L R L R L R L R
1 2 3 4 5 6 7 8 9 10 11
SRW-1
VIDEO OOOO PLAY LOCK
TCR LTC INTRP DF EXT-LK KEYINHI
AUDIO 00 00 00 00
H M S
SYSTEM IN: --:--:--:--
1080 LOCAL
12.2V REMAIN CH.COND
S59P
PB
(29PsF)
46min
4:2:2 21:46
1
1
Press the menu selection button "SYSTEM" on the
control panel.
The SYSTEM Setup menu appears.
2
Rotate the SELECT/ENTER dial to move the cursor to
OTHERS, and then press the dial.
A submenu window appears.
S Y S T E M S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEYMAP
KEYINHI MAP
REMOTE/LOCAL
SERVO
REC INHI OFF
EDIT
POWER
BATTERY
OTHERS
R E C L O C K
S RW-1
3
Rotate the SELECT/ENTER dial and select FORMAT
LIST in the submenu window.
2 - 6
A/E
KEY INHI
OFF ON
SELECT/ENTER
EMP LIGHT
L R
BACK
12 OFF ON
ADJUST
RECINHI
EJECT STOP PLAY REC
Z x B z
F
REW F FWD PAUSE
FUNC
m M X
Others
SOFT VERSION
HOURS METER
FORMAT LIST
OPTION LIST
0 0 : 0 0 : 0 0 :0 0
TC G
The format list screen appears.
F o r m a t L i s t
422 444SQ
23PsF
24PsF
25PsF
29PsF
50I
59I
50P
59P
60P
1080 23.08PsF 422 @ Select FPS
C A S S O U T
S R W- 1
A bar appears for formats that cannot be used. A
yellow or green check mark appears for formats that
can be used. The check mark is green for formats that
can be used when the SELECT FPS function is
enabled.
See 7-2 "Select FPS Function" (page 84) for more
information about the SELECT FPS function.
4
Move the cursor to the format you want to use.
To move the cursor left and right
Rotate the SELECT/ENTER dial.
To move the cursor up and down
Rotate the SELECT/ENTER dial with the FUNC
button held down.
5
Press the SELECT/ENTER dial.
"CANCEL" and "OK" appear at the bottom of the
screen.
6
Move the cursor to "OK", and then press the SELECT/
ENTER dial.
A message appears to inform you that the format has
been selected, and you return to the HOME screen.
Relation between recording and playback
signals and output signals to video
monitors
Signals in the formats shown in the following table are
output to the HD video monitor connected to the
MONITOR OUT HD SDI connector and to the SD
monitor connected to the MONITOR OUT SD SDI
connector.
S E L E C T F P S : O F F
1080 720
444HQ 422x2 422
00:00:00:00
T C G
5-1 Signal Format Settings
63