D Command Table - Icom IC-7700 Instruction Manual

D D Command table
Command Sub command
00 —
01 Same as
command 06
02 —
03 —
04 —
05 —
06 00
01
02
03
04
05
07
08
12
13
07 —
00
01
A0
B0
08 —
0001–0101*
09 —
0A —
0B —
0E 00
01
02
03
12
13
22
23
A1–A7
B0
B1
B2
D0
D3
0F 00
01
10 00
01
02
03
04
05
06
07
08
Description
Send frequency data
Send mode data
Read band edge frequencies
Read operating frequency
Read operating mode
Set operating frequency
Select LSB
Select USB
Select AM
Select CW
Select RTTY
Select FM
Select CW-R
Select RTTY-R
Select PSK
Select PSK-R
Select VFO mode
Select VFO-A
Select VFO-B
Equalize VFO-A and VFO-B
Exchange VFO-A and VFO-B
Select memory mode
Select memory channel
*P1=0100, P2=0101
Memory write
Memory to VFO
Memory clear
Scan stop
Programmed/memory scan start
Programmed scan start
∂F scan start
Fine programmed scan start
Fine ∂F scan start
Memory scan start
Select memory scan start
Set ∂F scan span (A1=±5 kHz;
A2=±10 kHz; A3=±20 kHz;
A4=±50 kHz; A5=±100 kHz;
A6=±500 kHz; A7=±1 MHz)
Set as non-select channel
Set as select channel
(1=★1; 2=★2; 3=★3; when no
data command is specified, the
previously set number or "★1" is
selected)
Set the number for select memory
scan (0=ALL; 1=★1; 2=★2; 3=★3)
Set scan resume OFF
Set scan resume ON
Turn the split function OFF
Turn the split function ON
Select 10 Hz (1 Hz) tuning step
Select 100 Hz tuning step
Select 1 kHz tuning step
Select 5 kHz tuning step
Select 9 kHz tuning step
Select 10 kHz tuning step
Select 12.5 kHz tuning step
Select 20 kHz tuning step
Select 25 kHz tuning step
Command Sub command
11 —
12 00 + RX ANT
01 + RX ANT
02 + RX ANT
03 + RX ANT
13 00
01
02
14 01 + Level data [AF] level setting
02 + Level data [RF] level setting
03 + Level data [SQL] level setting
05 + Level data [APF] level setting
06 + Level data [NR] level setting
07 + Level data Inside [TWIN PBT] setting or IF
08 + Level data Outside [TWIN PBT] setting
09 + Level data [CW PITCH] setting
0A + Level data [RF POWER] setting (0=max.
0B + Level data [MIC] setting (0=max. CCW to
0C + Level data [KEY SPEED] setting (0=max.
0D + Level data [NOTCH] setting
0E + Level data [COMP] setting
0F + Level data [DELAY] setting
11 + Level data [AGC] control setting
12 + Level data [NB] control setting
13 + Level data [DIGI-SEL] setting
14 + Level data [DRIVE] setting
15 + Level data [MONI GAIN] setting (0=max.
16 + Level data [VOX GAIN] setting (0=max.
17 + Level data [ANTI VOX] setting
14-3
CONTROL COMMAND
Description
Select/read attenuator
(00=OFF; 06=6 dB; 12=12 dB;
18=18 dB)
Select/read ANT1 selection
(00=RX ANT OFF;
01=RX ANT ON)
Select/read ANT2 selection
(00=RX ANT OFF;
01=RX ANT ON)
Select/read ANT3 selection
(00=RX ANT OFF;
01=RX ANT ON)
Select/read ANT4 selection
(00=RX ANT OFF;
01=RX ANT ON)
Announce with voice synthesizer
(00=all data; 01=frequency and
S-meter level; 02=receive mode)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=11 o'clock)
(0=11 o'clock to 255=max. CW)
(0=Pitch–550 Hz, 128=Pitch,
255=Pitch+550 Hz; 10 Hz steps)
(0=min. to 255=max.)
shift setting (0=max. CCW,
128=center, 255=max. CW)
(0=max. CCW, 128=center,
255=max. CW)
(0=300 Hz, 128=600 Hz,
255=900 Hz; 5 Hz steps)
CCW to 255=max. CW)
255=max. CW)
CCW to 255=max. CW)
(0=low freq. to 255=high freq.)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
CCW to 255=max. CW)
CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
14