GE MULTILINK ML2400 Instruction Manual page 140
Ethernet communications switch
Hide thumbs
Also See for MULTILINK ML2400:
- Quick start manual (70 pages) ,
- Quick start manual (62 pages)
Table of Contents
Advertisement
PORT MIRRORING AND SETUP
Example 9-1: Port setup
ML2400#
ML2400(device)##
ML2400(device)##
ML2400(device)##
Keys: E
Port
-------------------------------------------------------------------------------
9
10
11
12
13
14
15
16
ML2400(device)##
ML2400#
9–4
In Example 9-1, ports 11 and 12 are given specific names. Ports 9 and 13 are active, as
shown by the link status. Port 13 is set to 100 Mbps, and all other ports are set to 10 Mbps.
All ports are set to auto sensing (speed).
The port
and
speed
duplex
The
setting defaults to auto and senses speed and negotiates with the port at the
speed
other end of the link for data transfer operation (half-duplex or full-duplex). The "auto"
speed detection uses the IEEE 802.3u auto negotiation standard for 100Base-T networks. If
the other device does not comply with the 802.3u standard, then the port configuration on
the switch must be manually set to match the port configuration on the other device.
Possible port setting combinations for copper ports are:
• 10HDx: 10 Mbps, half-duplex
• 10FDx: 10 Mbps, full-duplex
• 100HDx: 100 Mbps, half-duplex
• 100FDx: 100 Mbps, full-duplex
Possible port settings for 100FX (fiber) ports are:
• 100FDx (default): 100 Mbps, full-duplex
• 100HDx: 100 Mbps, half-duplex
Possible port settings for 10FL (fiber) ports are:
• 10HDx (default): 10 Mbps, half-duplex
• 10FDx: 10 Mbps, full-duplex
Gigabit fiber-optic ports (Gigabit-SX and Gigabit-LX):
• 1000FDx (default): 1000 Mbps, full-duplex only
• Auto: The port operates at 1000FDx and auto-negotiates flow control with the
connected device.
device
setport port=11 name=JohnDoe
setport port=12 name=JaneDoe
show port
= Enable
H
= Half Duplex
M
= Multiple VLAN's
LI = Listening
F
= Forwarding
Name
Control
Dplx
B1
E
H
B2
E
H
JohnDoe
E
H
JaneDoe
E
H
B5
E
F
B6
E
H
B7
E
H
B8
E
H
exit
MULTILINK ML2400 ETHERNET COMMUNICATIONS SWITCH – INSTRUCTION MANUAL
CHAPTER 9: PORT MIRRORING AND SETUP
(data transfer operation) settings are summarized below.
D
= Disable
F
= Full Duplex
NA = Not Applicable
LE = Learning
B
= Blocking
Media
Link
Speed
Part
10Tx
UP
10
No
10Tx
DOWN
10
No
10Tx
DOWN
10
No
10Tx
DOWN
10
No
100Tx
UP
100
No
10Tx
DOWN
10
No
10Tx
DOWN
10
No
10Tx
DOWN
10
No
Auto
VlanID
GVRP
STP
E
1
-
-
E
1
-
-
E
1
-
-
E
1
-
-
E
1
-
-
E
1
-
-
E
1
-
-
E
1
-
-
Hide quick links:
Advertisement
Table of Contents
