Table 3-14. Result Code Definitions - Conexant H08-15355F Reference Manual

Code Message
+F4 +FCERROR
0 OK
1 CONNECT
2 RING
3 NO CARRIER
4 ERROR
5 CONNECT 1200
6 NO DIALTONE
7 BUSY
8 NO ANSWER
9 CONNECT 600
10 CONNECT 2400
11 CONNECT 4800
12 CONNECT 9600
13 CONNECT 7200
14 CONNECT 12000
15 CONNECT 14400
16 CONNECT 19200
17 CONNECT 38400
18 CONNECT 57600
19 CONNECT 115200
22 CONNECT
75TX/1200RX
23 CONNECT
1200TX/75RX
24 DELAYED
32 BLACKLISTED
3-58
Command Reference Manual

Table 3-14. Result Code Definitions

High speed fax data (V.27, V.29, V.33, or V.17) is expected but a V.21 signal is received.
A command line has been executed.
For X command values specifying no speed reporting, the modem has connected to the line and either the
line speed is 300 bps and line speed is enabled, or the DTE speed is 300 bps and DTE speed reporting is
enabled.
An incoming ring signal is detected on the line. What qualifies as a ring signal is determined by country-
dependent parameters, modifiable through ConfigurACE.
When cellular interface is selected, RING indicates that the cellular phone is receiving an receiving an
incoming call.
Sent when attempting to establish a call if:
Ringback is detected and later ceases but no carrier is detected within the period of time determined by
register S7, or
1. No ringback is detected within the period of time determined by register S7.
2. Also sent when the modem auto-disconnects due to loss of carrier.
For X0, sent for the following conditions:
1. If busy tone detection is enforced, busy or circuit busy has been detected.
2. If dial tone detection is enforced or selected, dial tone has not been detected.
Sent during an attempt to execute a command line if any of the following conditions occur:
1. The command line contains a syntax error.
2. The modem cannot execute a command contained in the command line, i.e., the command does
not exist or is not supported.
3. A command parameter within the command line is outside the permitted range.
For X0, X1, X2, and X3, this message is sent instead of DELAYED and BLACKLISTED.
The modem has connected to the line and either the line speed is 1200 bps and DCE speed reporting is
enabled, or the DTE speed is 1200 bps and DTE speed reporting is enabled.
For X2 and X4, the modem has been instructed to wait for dial tone during dialing but none is received.
When cellular phone interface is selected, indicates that cellular service is not currently available.
For X3 and X4, if busy tone detection is enforced, the busy (engaged) signal is detected on the line when
the modem is attempting to originate a call.
The modem is attempting to originate a call if a continuous ringback signal is detected on the line until the
expiration of the timer S7.
The modem has connected to the line, the DTE speed is 600 bps, and DTE speed reporting is enabled.
The modem has connected to the line and either the line speed is 2400 bps and DCE speed reporting is
enabled, or the DTE speed is 2400 bps and DTE speed reporting is enabled.
The modem has connected to the line and either the line speed is 4800 bps and DCE speed reporting is
enabled, or the DTE speed is 4800 bps and DTE speed reporting is enabled.
The modem has connected to the line and either the line speed is 9600 bps and DCE speed reporting is
enabled, or the DTE speed is 9600 bps and DTE speed reporting is enabled.
The modem has connected to the line at 7200 bps and DCE speed reporting is enabled.
The modem has connected to the line at 12000 bps and DCE speed reporting is enabled.
The modem has connected to the line at 14400 bps and DCE speed reporting is enabled.
The modem has connected to the line and either the line speed is 19200 bps and DCE speed reporting is
enabled, or the DTE speed is 19200 bps and DTE speed reporting is enabled.
The modem has connected to the line, the DTE speed is 38400 bps, and DTE speed reporting is enabled.
The modem has connected to the line, the DTE speed is 57600 bps, and DTE speed reporting is enabled.
The modem has connected to the line, the DTE speed is 115200 bps, and DTE speed reporting is
enabled.
The modem has established a V.23 originate connection and line speed reporting is enabled.
The modem has established a V.23 answer connection and line speed reporting is enabled.
For X4, sent when a call fails to connect and the number dialed is considered 'delayed' due to country
blacklisting requirements.
For X4, sent when a call fails to connect and the number dialed is considered 'blacklisted'.
Meaning
Conexant
1118