Index - Conexant H08-15355F Reference Manual

#
#UD – Last Call Status Report
%
%C - Enable/Disable Data Compression
%E - Enable/Disable Line Quality Monitor, Auto-Retrain, and
Auto-Rate Renegotiation
%TT - PTT Test Command
&
&C - RLSD Behavior
&D - DTR Behavior
&F - Set to Factory-Defined Configuration
&G - Select Guard Tone
&K - Flow Control
&M - Asynchronous/Synchronous Mode Selection
&P - Select Pulse Dial Make/Break Ratio
&Q - Sync/Async Mode
&T - Local Analog Loopback Test
&V - Display Current Configuration and Stored Profiles
&W - Store Current Configuration
*
*B - Display Blacklisted Numbers
*D - Display Delayed Numbers
+
+A8A: - Answer Signal Indication
+A8C: - Calling Tone Indication
+A8E - V.8 and V.8bis Operation Controls
+A8I: - CI Signal Indication
+A8J: - V.8 Negotiation Complete
+A8M: - V.8 Menu Report
+A8M - Send V.8 Menu Signals
+A8R: - V.8bis Signal and Message Reporting
+DR - Data Compression Reporting
+DS - Data Compression
+EB - Break Handling in Error Control Operation
+EFCS - 32-bit Frame Check Sequence
+ER - Error Control Reporting
+ES - Error Control and Synchronous Mode Selection
+ESA - Configure Synchronous Access Mode
+ESR - Selective Repeat
+ETBM - Call Termination Buffer Management
+FAE - Auto Answer Enable
+FAR - Adaptive Reception Control
+FCL - Carrier Loss Timeout
+FCLASS- Select Active Service Class
+FCLASS=1 - Select Facsimile Class 1 Mode
+FCLASS=1.0 - Select Facsimile Class 1.0 Mode
+FCLASS=8 - Select Voice Mode
1118
Command Reference Manual

6. INDEX

+FCLASS=80 - Select VoiceView Mode
+FDD - Double Escape Character Replacement
3-41 +FIT - DTE Inactivity Timeout
+FLO - Flow Control
+FMI - Request Manufacturer Identification
3-32 +FMM - Request Model Identification
+FMR - Request Revision Identification
3-26 +FPR - Fixed DTE Rate
3-48 +FRH - Receive Data with HDLC Framing
+FRM - Receive Data
+FRS - Receive Silence
3-13 +FTH - Transmit Data with HDLC Framing
3-13 +FTM - Transmit Facsimile
3-3 +FTS - Transmit Silence
3-21 +GCAP - Request Complete Capabilities List
3-14 +GCI - Country of Installation
3-14 +GMI - Request Manufacturer Identification
3-22 +GMM - Request Model Identification
3-14 +GMR - Request Revision Identification
3-4 +GOI - Request Global Object Identification
3-22 +GSN - Request Product Serial Number Identification
3-23 +IFC - DTE-Modem Local Flow Control
+ILRR - DTE-Modem Local Rate Reporting
+IPR - Fixed DTE Rate
3-23 +ITF - Transmit Flow Control Thresholds
3-23 +MR - Modulation Reporting Control
+MS - Modulation Selection
+VBT - Buffer Threshold Setting
3-35 +VCID - Caller ID (CID)
3-35 +VDR - Distinctive Ring
3-33 +VDT - Control Tone Cadence Reporting
3-34 +VDX - Speakerphone Duplex Mode
3-36 +VGM - Microphone Gain
3-36 +VGR - Voice Gain Receive (Record Gain)
3-34 +VGS - Speaker Gain
3-36 +VGT - Voice Gain Transmit (Playback Volume)
3-31 +VIP - Voice Initialize All Parameters
3-31 +VIT - Voice Inactivity Timer (DTE/Modem
3-28 +VNH - Automatic Hang-up Control
3-29 +VPR - Select DTE/Modem Interface Rate)
3-29 +VRA - Ringback Goes Away Timer
3-27 +VRN - Ringback Never Appeared Timer
3-39 +VRX - Start Modem Receive (Record)
3-29 +VSD - Silence Detection (Quiet and Silence
3-30 +VSM - Compression Method Selection
4-4 +VSP - Speakerphone ON/OFF
4-8 +VTD - Beep Tone Duration Timer
4-9 +VTR - Start Voice Transmission and Reception (Voice Duplex)5-
3-2
4-4 +VTS - Send Voice Tone(s)
4-4 +VTX - Start Modem Transmit (Playback
5-4 +WS= – Enable/Disable PDC
Conexant
5
5-4
4-9
4-10
4-12
4-11
4-12
4-12
4-11
4-7
4-6
4-5
4-7
4-5
4-4
3-6
3-7
3-5
3-5
3-5
3-6
3-6
3-16
3-16
3-15
3-40
3-25
3-24
5-18
3-2
5-16
5-17
5-20
5-21
5-8
5-21
5-8
5-5
5-9
5-4
5-19
5-12
5-12
5-5
5-13
5-14
5-20
5-15
5-6
5-8
3-56
6-1