Agilent Technologies InfiniiVision 3000 X-Series Programmer's Manual page 1276

Index
query subsystem, 242, 290
querying setup, 263
querying the subsystem, 878
queues, clearing, 1124
quick reference, commands, 73
quoted ASCII string, 158
QYE (Query Error) status bit, 166,
R
ramp symmetry, waveform generator,
ramp symmetry, waveform generator
modulating signal, 1020
ramp waveform generator output,
range, 327, 874
range for channels, 277
range for duration trigger, 926
range for external trigger, 320
range for full-scale vertical axis, 349
range for glitch search, 790
range for glitch trigger, 914
range for time base, 869
range of offset values, 270
range qualifier, 913
range, I2S, 703
ranges, value, 158
rate, 238
ratio measurements with X cursors,
ratio measurements with Y cursors,
ratio of AC RMS values measured between
channels, 462
Ratio, power modulation analysis,
raw acquisition record, 974
RCL (Recall), 175
Rds (dynamic ON resistance) waveform,
Rds(on) value for conduction calculation,
reactive power, 485, 562
read configuration, 171
ReadIEEEBlock method, 63, 67, 69
ReadList method, 63, 67
ReadNumber method, 63, 67
readout, 1068
ReadString method, 63, 67
real (actual) power, 562
real power, 486
real-time acquisition mode, 231
recall, 175, 598, 862
recall arbitrary waveform, 599
RECall commands, 597
recall filename, 600, 1006
recall mask, 601
recall path information, 602
recall reference waveform, 604
recall setup, 603
recalling and saving data, 298
receiver width, I2S, 693
RECTangular window for transient signals,
reference, 327, 870
reference for time base, 1093
reference waveform save source,
reference waveform, recall, 604
reference waveform, save, 627
1276
reference waveforms, clear,
reference waveforms, display,
reference waveforms, label,
reference waveforms, save to,
reference waveforms, skew,
reference waveforms, Y offset,
168 reference waveforms, Y range,
reference waveforms, Y scale,
reference, lister,
registers, 168, 175, 179, 192, 201, 203, 205,
207, 209, 211, 213, 216,
1011
registers, clearing,
reject filter, 904
reject high frequency,
1007
reject noise, 887
relative standard deviation,
remote control examples,
Remote Terminal Address (RTA), M1553
trigger, 736
remove cursor information,
remove labels,
remove message from display,
reorder channels,
repetitive acquisitions,
report errors, 855
report transition, 452,
reporting status,
reporting the setup,
387
request service,
392
Request-for-OPC flag clear,
reset, 176
reset conditions,
552
reset defauts, waveform generator,
reset mask statistics,
reset measurements,
586
resolution of printed copy,
588
resource session object,
ResourceManager object,
restore configurations, 171, 175, 179,
restore labels,
restore setup,
return values, query,
returning acquisition type,
returning number of data points,
RF burst demo signal,
right reference,
ringing pulse demo signal,
ripple (output) analysis,
ripple, output,
rise time measurement,
rise time of positive edge,
Rise Time, power modulation analysis,
rising edge count measurement,
rising pulse count measurement,
RMS - AC, power modulation analysis,
RMS value measurement, 423,
roll time base mode,
337
root (:) commands, 187,
root level commands,
RQL (Request Control) status bit, 166,
626
RQS (Request Service),
RS-232/UART triggering,
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
1035
1036
1037
1038
1039
1040
1041
1042
378
218
1124
881
451
1147
381
305
854
193
219
454
1105
878
183
165
176
1028
501
303
1063
63
63
862
305
175
1145
239
232
283
870
282
563
487
406
441
552
432
435
552
463
867
190
3
168
183
630
RST (Reset), 176
rules, tree traversal, 1143
rules, truncation, 1140
run, 184, 219
Run bit, 207, 209
run count, current harmonics analysis,
run mode, mask test, 508
running configuration, 179, 862
RUNT SEARch commands, 792
runt search polarity, 793
runt search qualifier, 794
runt search source, 795
runt search, pulse time, 796
RUNT trigger commands, 927
runt trigger polarity, 928
runt trigger qualifier, 929
runt trigger source, 930
runt trigger time, 931
Rx frame count (UART), 762
Rx source, 767
S
sample rate, 238
sampled data, 1055
sampled data points, 969
SAV (Save), 179
save, 179, 607
save arbitrary waveform, 608
SAVE commands, 605
save current harmonics analysis results,
save filename, 609
save image, 610
save image with inksaver, 613
save mask, 615, 616
save mask test failures, 511
save path information, 619
save reference waveform, 627
save setup, 620
save to reference waveform location,
save waveform data, 621
saved image, area, 1090
saving and recalling data, 298
SBUS A429 commands, 634
SBUS CAN commands, 652
SBUS commands, 629
SBUS I2S commands, 688
SBUS<n> commands, general, 631
scale, 351, 871, 875
scale factors output on hardcopy, 361,
scale for channels, 278
scale units for channels, 279
scale units for external trigger, 321
scaling display factors, 271
SCPI commands, 71
SCPI.NET example in C#, 1248
SCPI.NET example in IronPython,
SCPI.NET example in Visual Basic .NET,
SCPI.NET examples, 1248
scratch measurements, 1067
screen area for hardcopy print, 359
screen area for saved image, 1090
543
618
1038
611
1260
1254