Agilent Technologies InfiniiVision 3000 X-Series Programmer's Manual page 1271

Fall Time, power modulation analysis,
falling edge count measurement,
falling pulse count measurement,
Fast Fourier Transform (FFT) functions, 326,
334, 335, 337, 1059
FF values in waveform data, 969
FFT (Fast Fourier Transform) functions, 326,
334, 335, 337, 1059
FFT (Fast Fourier Transform) operation, 347,
981
FFT vertical units, 336
fifty ohm impedance, disable setting,
filename for hardcopy, 1062
filename for recall, 600, 1006
filename for save, 609
filter for frequency reject, 904
filter for high frequency reject, 881
filter for noise reject, 887
filter used to limit bandwidth, 264,
filters to Fast Fourier Transforms,
filters, math, 327
fine horizontal adjustment (vernier),
fine vertical adjustment (vernier),
finish pending device operations,
first point displayed, 991
FLATtop window for amplitude
measurements, 337
FLEXray autoset for event trigger,
FLEXray autosetup, 671
FlexRay demo signal, 284
FlexRay frame counters, reset, 675
FLEXray SEARch commands, 814
FlexRay serial search, cycle, 815
FlexRay serial search, data, 816
FlexRay serial search, data length,
FlexRay serial search, frame, 818
FlexRay serial search, mode, 819
FLEXray source, 678
FLEXray trigger, 679
FLEXray trigger commands, 669
FM burst demo signal, 283
FM modulation type, waveform
generator, 1023
force trigger, 880
format, 971, 976
format (word), ARINC 429, 641
format for block data, 171
format for generic video, 944, 948
format for hardcopy, 1061
format for image, 612
format for waveform data, 622
FormattedIO488 object, 63
formfeed for hardcopy, 358, 362
formulas for data conversion, 964
frame, 745
frame counters (CAN), error, 654
frame counters (CAN), overload,
frame counters (CAN), reset, 656
frame counters (CAN), total, 657
frame counters (FlexRay), null, 674,
frame counters (FlexRay), reset,
frame counters (FlexRay), total, 677
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
552 frame counters (UART), error,
427 frame counters (UART), reset,
428 frame counters (UART), Rx frames,
frame counters (UART), Tx frames,
frame ID, FLEXray BSS event trigger,
frame ID, FLEXray frame trigger,
frame type, FLEXray frame trigger,
framing, 743
frequency deviation, waveform generator FM
modulation,
frequency measurement, 61, 406,
861 frequency measurements with X cursors,
frequency resolution,
frequency span of display,
frequency versus dB,
Frequency, power modulation analysis,
front panel mode,
front panel Single key,
318 front panel Stop key,
337 front-panel lock,
FSK modulation type, waveform
872 generator,
280 FSK rate, waveform generator
172 modulation,
full-scale horizontal time, 869,
full-scale vertical axis defined,
function, 225, 333, 334, 335, 337, 346, 347,
681 349, 350, 351, 1059,
FUNCtion commands,
function memory,
function turned on or off,
function, demo signal,
function, first source input,
function, second source input,
817 function, waveform generator,
functions, 981
G
g(t) source, first input channel,
g(t) source, math operation,
g(t) source, second input channel,
gain for Ax + B math operation,
gateway IP, 52
gaussian pulse waveform generator
output, 1009
general SBUS<n> commands,
general SEARch commands,
general trigger commands,
GENeric, 944,
generic video format, 944,
Generic video trigger, edge number,
Generic video trigger, greater than sync pulse
width time,
Generic video trigger, horizontal sync
control, 950
655
Generic video trigger, horizontal sync pulse
time, 951
glitch demo signal,
676
glitch duration,
675
glitch qualifier,
GLITch SEARch commands,
760
761
762
763
682
686
687
1015
426
387
337
335
326
552
888
221
223
856
1023
1018
874
349
1060
323
222
1060
282
352
354
1007
341
340
342
344
631
778
879
948
948
949
952
282
914
913
785
glitch search, greater than value,
glitch search, less than value, 787
glitch search, polarity, 788
glitch search, qualifier, 789
glitch search, range, 790
glitch search, source, 791
glitch source, 915
GLITch trigger commands, 907
glitch trigger duration, 909
glitch trigger polarity, 912
glitch trigger source, 909
GPIB interface, 51, 52
graticule area for hardcopy print,
graticule colors, invert for hardcopy, 363,
graticule colors, invert for image,
grayscale palette for hardcopy, 371
grayscale palette for image, 614
grayscaling on hardcopy, 1063
greater than qualifier, 913
greater than time, 909, 914, 922,
greater than value for glitch search,
groups of digital channels, 523, 525, 527,
1051
H
HANNing window for frequency
resolution, 337
hardcopy, 215, 358
HARDcopy commands, 357
hardcopy factors, 361, 611
hardcopy filename, 1062
hardcopy format, 1061
hardcopy formfeed, 362
hardcopy grayscale, 1063
hardcopy invert graticule colors, 363,
hardcopy layout, 364
hardcopy palette, 371
hardcopy print, area, 359
hardcopy printer driver, 1065
head type, probe, 272
header, 1139
high pass filter math function, 327
high resolution acquisition type, 963
high trigger level, 884
high-frequency reject filter, 881,
high-level voltage, waveform generator,
high-pass filter cutoff frequency,
high-pass filter math function, 347
high-resolution acquisition type,
hold time, setup and hold trigger,
hold until operation complete, 172
holdoff time, 882
holes in waveform data, 969
hop frequency, waveform generator FSK
modulation, 1017
horizontal adjustment, fine (vernier),
horizontal position, 873
horizontal scale, 871, 875
horizontal scaling, 976
horizontal time, 869, 874, 1068
Host name softkey, 52
Index
786
359
1064
613
926
786
1064
904
1030
338
228
936
872
1271