Download Print this page

Cisco AS5350 - Universal Access Server Configuration Manual

Universal gateway software configuration guide.
Hide thumbs

Advertisement

Cisco AS5350 and Cisco AS5400 Universal
Gateway Software Configuration Guide
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-3418-02 B0

Advertisement

Troubleshooting

   Also See for Cisco AS5350 - Universal Access Server

   Related Manuals for Cisco AS5350 - Universal Access Server

   Summary of Contents for Cisco AS5350 - Universal Access Server

  • Page 1

    Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-3418-02 B0...

  • Page 2

    CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE,...

  • Page 3: Table Of Contents

    Where to Go Next 1-14 Verifying Basic Setup C H A P T E R Analyzing the System Boot Dialog Checking the Initial Running Configuration Investigating Memory Usage Inspecting CPU Utilization Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 4

    Configuring the D Channels for ISDN Signaling 3-23 Configure 3-24 Verify 3-25 Configuring the Universal Port Card and Lines 3-26 SPE Firmware 3-27 Configure 3-28 Verify 3-29 Configuring Clocking 3-31 Trunk-Card Ports 3-31 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 5

    Where to Go Next 4-12 Managing and Troubleshooting the Universal Port Card C H A P T E R Managing SPE Performance Statistics Configuration Viewing SPE Performance Statistics Managing Ports Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 6

    Other Bandwidth-Reduction Features 6-20 Additional Resources 6-23 Using the Setup Script A P P E N D I X Getting Started Cisco AS5350 or Cisco AS5400 with AS54-DFC-CT3 and AS54-DFC-108NP Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 7

    Two 8 T1/PRI ISDN with RADIUS (AAA) and Resource Pooling C-59 Two 8 E1/PRI ISDN with RADIUS (AAA) and Resource Pooling C-71 CT3 with Resource Pooling, AAA, and Modem C-75 N D E X Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 8

    Contents Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide viii OL-3418-02 B0...

  • Page 9

    Whether you are a corporate end user or a competitive Internet service provider (ISP), you have purchased a Cisco AS5350 or Cisco AS5400 universal gateway to provide dial-up services that facilitate accessibility for remote or roaming personnel, or Internet admission to consumers for e-mail, e-commerce, and web browsing.

  • Page 10

    The following details where you can find your basic and advanced configuration information: • Chapter 1—Get familiar with your Cisco AS5350 or Cisco AS5400, learn how to use the command-line interface (CLI), and upgrade your Cisco IOS software, if necessary.

  • Page 11

    – Configuration guides and command references (see Figure – The Cisco IOS documentation set for your release is available online at Note http://www.cisco.com/univercd/cc/td/doc/product/software/ Note The abbreviations next to the book icons are page designators (for example, FC, FR, and so on), which are defined in a key in the index of each document to help with navigation.

  • Page 12

    • Traffic Filtering and Firewalls • X.25 and LAPB • IP Security and Encryption • Passwords and Privileges • Neighbor Router Authentication • IP Security Options • Supported AV Pairs Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 13

    • Congestion Avoidance • Voice over ATM • Policing and Shaping • Voice over HDLC • Signalling • Video Support • Link Efficiency • Universal Broadband Mechanisms Features Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide xiii OL-3418-02 B0...

  • Page 14: Document Conventions

    This symbol means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 15

    La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 16: Obtaining Documentation

    Obtaining Documentation These sections explain how to obtain documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com Translated documentation is available at this URL: http://www.cisco.com/public/countries_languages.shtml...

  • Page 17: Ordering Documentation

    We appreciate your comments. Obtaining Technical Assistance Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.

  • Page 18: Technical Assistance Center

    Cisco TAC Web Site You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to this URL: http://www.cisco.com/tac...

  • Page 19: Cisco Tac Escalation Center

    Obtaining Technical Assistance If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC Web Site, you can open a case online by using the TAC Case Open tool at this URL: http://www.cisco.com/tac/caseopen...

  • Page 20

    Technical Assistance Center Obtaining Technical Assistance Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 21: Basic Hardware Architecture

    Note that the latter requires use of Cisco IOS release 12.2(2)XB or later. This chapter provides a brief profile of the Cisco AS5350 and Cisco AS5400 universal gateway hardware components and functionality, details how to use the Cisco IOS command-line interface (CLI), and describes how to upgrade your Cisco IOS software: •...

  • Page 22: C H A P T E R 1 Understanding Basic Hardware Architecture And Cisco Ios Software

    Modems TDM bus T1 controllers PRI lines PSTN POTS line BRI line Client Client Client ISDN modem router Legend = Synchronous PPP = Asynchronous PPP = Configuration template Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 23: Exploring The Cisco Ios File System

    ROM, raw system memory, Xmodem, and Flash load helper log) IFS first appeared in Cisco IOS Releases 11.3 AA and 12.0. For more information about IFS, refer to the chapter “Using the Cisco IOS File System” in the Cisco IOS Release 12.0 Configuration Fundamentals Configuration Guide, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/fun_c/fcprt2/fcifs.htm...

  • Page 24

    250 MHz (Cisco AS5350 and Cisco AS5400) 390 MHz (Cisco AS5400HPX) Processor memory The Cisco IOS image is initially read out of Flash memory, decompressed, and loaded into processor memory (also known as main memory or DRAM). Routing tables, call control blocks, and other data structures are also stored here.

  • Page 25

    Boot Flash or Flash memory. Note For more information on crashinfo files, refer to Retrieving Information from the Crashinfo File, available online at http://www.cisco.com/warp/public/63/crashinfo.html. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 26: Exploring Cisco Ios Software

    It supports encryption technologies, but it is not user accessible. Exploring Cisco IOS Software This section describes what you need to know about the Cisco IOS software (the software that runs the gateway) before you configure the gateway using the CLI. This section includes: •...

  • Page 27: Understanding Command Modes

    For example, if you were in global configuration mode, typed the command arap, and wanted to see all the keywords and arguments for that command, you would type arap ? Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 28

    T1 controller. Step 6 Displays the only command (timeslots) Router(config-controller)# ds0-group 1 ? timeslots List of timeslots in the ds0-group available in ds0-group 1. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 29: Undoing A Command Or Feature

    Undoing a Command or Feature If you want to undo a command you entered or disable a feature, enter the keyword no before most commands; for example, no ip routing. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 30: Saving Configuration Changes

    Timesaver reload or power outage. Upgrading to a New Cisco IOS Release Obtain new Cisco IOS features and more stable code by upgrading to a new Cisco IOS release. Step 1 Display the contents of Flash memory: Router# cd flash:...

  • Page 31

    Caution gateway if the checksum reports errors. Verify that the new image was downloaded. In this example, notice that the Cisco IOS Release Step 3 12.1(1)XD image is the first in Flash memory, so it is loaded during the boot sequence. To boot using the new image, you must either delete the unwanted image or use the boot system command to specify the alternate image to use during the boot sequence.

  • Page 32

    Step 5 Reload the Cisco AS5350 or Cisco AS5400 to run the new image. If you erased the old Cisco IOS image, make sure that the boot system flash oldiosname.bin command is not enabled and pointing to the old image file name;...

  • Page 33: Changing Console Line Speed

    Log in to your Cisco AS5350 or Cisco AS5400 through the AUX port or Telnet VTY session. Enter the show running-config command and determine what speed your line console is set. Possible console speeds are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200.

  • Page 34: Where To Go Next

    • configuration before configuring the Cisco AS5350 or Cisco AS5400 universal gateway using the CLI. To commission is to systematically execute basic configuration tasks that prepare your system for data call processing.

  • Page 35: Analyzing The System Boot Dialog

    • Analyzing the System Boot Dialog The Cisco AS5350 and Cisco AS5400 have a specific boot sequence. To view the boot sequence through a terminal session, you must have a console connection to the gateway before it powers up. Note If you observe no messages on the console port, check that the baud rate is configured correctly.

  • Page 36: Chapter 2 Verifying Basic Setup

    Step 2 Cisco IOS release, available memory, hardware interfaces, and modem lines are displayed: If a card type is not recognized, verify that you are running the optimum version of Cisco IOS Note software. Refer to the hardware-software compatibility matrix, available online at http://cco-sj-1.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi...

  • Page 37

    00:01:10: %TRUNK_CLOCK-6-BAD_CLOCKS: There are no good clocks in the system. Remain in HOLDOVER mode 00:01:10: %TRUNK_CLOCK-6-BAD_CLOCKS: There are no good clocks in the system. Remain in HOLDOVER mode Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 38

    00:01:10: %TRUNK_CLOCK-6-BAD_CLOCKS: There are no good clocks in the system. Remain in HOLDOVER mode Step 5 Enter the show version command to check the system hardware, Cisco IOS image name, uptime, and restart reason: Router> show version Cisco Internetwork Operating System Software IOS (tm) 5350 Software (C5350-JS-M), Version 12.1(20001028:174051)]...

  • Page 39: Checking The Initial Running Configuration

    The gateway booted from this image location. System image file is..Checking the Initial Running Configuration The Cisco IOS software creates an initial running configuration. Inspect the configuration to get familiar with the default settings. User input is shown in boldface type. Router> enable...

  • Page 40: Checking The Initial Running Configuration

    Async4/01 no ip address no ip route-cache interface Async4/02 no ip address no ip route-cache interface Async4/107 no ip address no ip route-cache Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 41: Investigating Memory Usage

    InOut scheduler allocate 10000 400 The Cisco AS5350 or Cisco AS5400 displays every asynchronous interface it recognizes. Therefore, if your system has a large number of asynchronous interfaces, the running-configuration will be very long. To aggregate the asynchronous interfaces, you must assign them to a Group-Async Interface using the command group-range.

  • Page 42: Inspecting Cpu Utilization

    To learn more about management information bases (MIBs), see the online references at http://www.cisco.com/univercd/cc/td/doc/product/software/. Select your Cisco IOS release and search under new feature documentation. Inspecting CPU Utilization Enter the show process cpu command and then the show process cpu history command to investigate high CPU utilization.

  • Page 43: Inspecting Cpu Utilization

    If you see high utilization numbers in the top line of the output, for example over 50%, inspect the columns 5Sec, 1Min, and 5Min. Find the process that uses the most CPU power. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 44: Chapter 3 Basic Configuration Using The Command-line Interface

    For more advanced configuration topics, refer to the Cisco IOS software configuration guide, feature modules, and command reference publications that pertain to your Cisco IOS software release. Check Configuring Selected 12.1 Cisco IOS Software Features, available online at •...

  • Page 45

    After you have verified your basic setup, you are ready to begin configuring basic tasks that prepare your system for data call processing. This chapter describes how to use the Cisco IOS software command-line interface (CLI) to commission your Cisco AS5350 or Cisco AS5400 universal gateway and includes the following tasks: Configuring the Host Name, Password, and Time Stamps, page 3-2 •...

  • Page 46: Configuring The Host Name, Password, And Time Stamps

    Configuring the Host Name, Password, and Time Stamps The first configuration tasks you might want to execute are assign a host name to your Cisco AS5350 or Cisco AS5400, set an encrypted password, and turn on time stamps because: •...

  • Page 47: Configure

    Using 1888 out of 512000 bytes version XX.X hostname AS5400 enable secret 5 $1$60L4$X2JYOwoDc0.kqa1loO/w8/ Check the host name and encrypted password displayed near the top of the command output. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 48: Configuring Local Aaa Security

    PPP authentication to use the local database if the session was not already authenticated by login. AAA (called triple A) is the Cisco IOS security model used on all Cisco devices. AAA provides the primary framework through which you set up access control on the Cisco AS5350 or Cisco AS5400.

  • Page 49: Creating A Login Banner

    A successful login means that your local username works on any TTY or VTY line. Do not disconnect your session until you can log in. Note For comprehensive information about how to implement a Cisco AAA-based security environment for dial-based and router environments, see Cisco AAA Implementation Case Study, available online at http://www.cisco.com/univercd/cc/td/doc/cisintwk/intsolns/aaaisg/index.htm...

  • Page 50: Configuring Loopback Interfaces, Fast Ethernet Interfaces, And Ip Route

    DNS server in your backbone. Make sure that the backbone routers are configured to get to the gateway; otherwise, the ping does not work. Configure the backbone routers to support the routes to the networks you are using. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 51: Configuring The Asynchronous Group Interface

    Basic Configuration Using the Command-Line Interface Configuring the Asynchronous Group Interface An 80% ping-success rate is normal for the first time you ping an external device. The Cisco AS5350 Note and Cisco AS5400 do not have an Address Resolution Protocol (ARP) entry for the external device. A 100% success rate is achieved the next time you ping the device.

  • Page 52

    *7/106 192.168.10.100 34.4.90.1 1500 *7/107 192.168.10.100 34.1.42.1 1500 Rcvd: 25762 packets, 1052214 bytes 0 format errors, 891 checksum errors, 0 overrun Sent: 8891 packets, 222264 bytes, 0 dropped Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 53: Configuring Channelized T1 And E1 Trunk Cards

    For configuration information about leased-line or nondial use, see the Cisco IOS publication Note Configuration Fundamentals Configuration Guide available online. You can install, in one Cisco AS5350 or Cisco AS5400 chassis, a maximum of two T1 trunk cards, two Note E1 trunk cards, or one CT3 trunk card.

  • Page 54: Verify

    For details on the TDM feature, refer to the Cisco IOS software configuration guide and command reference publications. These publications are available on the Documentation CD-ROM that ships with your gateway and on the World Wide Web from the Cisco home page, or you can order printed copies. See “Obtaining Documentation” on page xvi.

  • Page 55: Configuring A Channelized T3 Trunk Card

    Trunk-card slots are numbered sequentially from 1 to 7. Port number value is always 0. Under the CT3, the CT1 controller numbering convention is dfc-slot/port:channel in CLI commands. Port numbering values range from 1 to 28. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-11 OL-3418-02 B0...

  • Page 56: Configure

    0 P-bit Severely Err Secs, 0 Severely Err Framing Secs 0 Unavailable Secs, 0 Line Errored Secs 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs Total Data (last 24 hours) Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-12 OL-3418-02 B0...

  • Page 57: Configuring Isdn Pri

    Request PRI Line and Switch Configuration from a Telco Service Provider Before configuring ISDN PRI on your Cisco router, you need to order a correctly provisioned ISDN PRI line from your telecommunications service provider. This process varies from provider to provider on a national and international basis. However, some general guidelines follow: •...

  • Page 58: Controller Numbering

    Step 3 AS5400(config)# isdn switch-type Selects a service provider switch type that switch-type accommodates PRI. (Refer to Table 3-3 for a list of supported switch type keywords.) Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-14 OL-3418-02 B0...

  • Page 59: Configure

    30 B channels and 1 D channel. B channel numbers range 1 to 31; channel 16 is the D channel for E1. Corresponding serial interface numbers range 0 to 30. In commands, the D channel is interface serial slot/port:15—for example, interface serial 1/0:15. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-15 OL-3418-02 B0...

  • Page 60: Verify

    0 C-bit Coding Violation, 0 P-bit Err Secs, 0 P-bit Severely Err Secs, 0 Severely Err Framing Secs, 0 Unavailable Secs, 0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-16 OL-3418-02 B0...

  • Page 61

    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 0 Active Layer 3 Call(s) Activated dsl 27 CCBs = 0 The Free Channel Mask: 0x807FFFFF Total Allocated ISDN CCBs = 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-17 OL-3418-02 B0...

  • Page 62

    0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide...

  • Page 63

    Basic Configuration Using the Command-Line Interface Configuring ISDN PRI Your Cisco AS5350 or Cisco AS5400 supports a total of 248 ISDN channels per ingress trunk card. If Note you are configuring individual T1 channels of your CT3 for backup links or serial backhaul connections, the CT1s must be configured into channel-groups—each channel-group using 24 timeslots or channels.

  • Page 64: Configuring Ds0 Trunk Group Dial Out

    The TGRM is used to store configuration information and to accept or select an interface from a trunk group when requested. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-20 OL-3418-02 B0...

  • Page 65: Configure

    A trunk with no preference is given the highest preference. The following examples show the configuration steps for PRI signalling. Controller T1 3 is a trunk configured for PRI. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-21 OL-3418-02 B0...

  • Page 66: Configure

    Hunt Scheme is least-used Max Calls (Incoming): NOT-SET (Any) NOT-SET (Voice) NOT-SET (Data) Max Calls (Outgoing): NOT-SET (Any) NOT-SET (Voice) NOT-SET (Data) Retries: 0 Trunk 2/1:23 Preference 10 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-22 OL-3418-02 B0...

  • Page 67: Configuring The D Channels For Isdn Signaling

    The D channel notifies the central office switch to send the incoming call to particular timeslots on the Cisco gateway or router. Each one of the B channels carries data or voice. The D channel carries signaling for the B channels. The D channel identifies if the call is a circuit switched digital call or an analog modem call.

  • Page 68: Configure

    On a CE1 PRI line, the serial interface is 1/0:15. Step 4 AS5400(config-if)# ip address Assigns an IP address and subnet mask to the 172.16.254.254 255.255.255.0 interface. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-24 OL-3418-02 B0...

  • Page 69: Configure

    0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions Timeslot(s) Used:24, Transmitter delay is 0 flags AS5400# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-25 OL-3418-02 B0...

  • Page 70: Configuring The Universal Port Card And Lines

    Forwards converted and packetized data to the main processor, which examines the data and • forwards it to the backhaul egress interface Supports all modem standards (such as V.34 and V.42bis) and features, including dial-in and dial-out • Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-26 OL-3418-02 B0...

  • Page 71: Spe Firmware

    SPE firmware is automatically downloaded to a universal port card from the Cisco AS5350 or Cisco AS5400 when you boot the system for the first time or when you insert a universal port card while the system is operating. When you insert cards while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.

  • Page 72: Configure

    Step 6 Enables remote IP users running a PPP application AS5400(config-line)# autoselect ppp to dial in, bypass the EXEC facility, and connect directly to the network. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-28 OL-3418-02 B0...

  • Page 73: Configure

    Call type: (m)modem (d)digital (f)fax-relay (v)voice (_)not in use System resources summary: ====================== Total ports: 108, in use ports: 0, disabled ports: 0, free ports: 108 Total active calls: modem voice digital fax-relay Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-29 OL-3418-02 B0...

  • Page 74

    If you are having trouble, make sure you turned on the protocols for connecting to the lines (transport input all) and configured for incoming and outgoing calls (modem inout). Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-30...

  • Page 75: Configuring Clocking

    Basic Configuration Using the Command-Line Interface Configuring Clocking Configuring Clocking The time-division multiplexing (TDM) bus on the Cisco AS5350 and Cisco AS5400 backplane can receive an input clock from one of four basic sources on the gateway: CT1, CE1, and CT3 trunk cards •...

  • Page 76: Free-running Clock

    A clock with priority of 100 cannot drive the TDM clock. Step 4 Returns to privileged EXEC mode. AS5400(config)# Ctrl-Z AS5400# Step 5 AS5400# copy running-config startup-config Saves your changes when ready. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-32 OL-3418-02 B0...

  • Page 77: Configuration Examples

    State ------------------------------------------------------------- Trunk cards controllers clock health information ------------------------------------------------ Slot Type 7 6 5 4 3 2 1 0 B B B B B B B B Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-33 OL-3418-02 B0...

  • Page 78: Verify

    Trunk Good Default Trunk cards controllers clock health information Slot Type 7 6 5 4 3 2 1 0 B B B B G G G G Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-34 OL-3418-02 B0...

  • Page 79

    The most common reason for clock slip problems is that the dial-tdm-clock priority parameter is set improperly. Change the default setting for dial-tdm-clock priority from free-running clock to a setting that matches your system requirements. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-35 OL-3418-02 B0...

  • Page 80: Enabling Ip Basic Setup

    Specifies the primary and secondary name servers. ip name-server 172.22.11.10 ip name-server 172.22.12.11 The ip name-server command is used for mapping names to IP addresses. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-36 OL-3418-02 B0...

  • Page 81: Testing Asynchronous Shell Connections

    Basic modem links • • Basic IP functionality to support shell sessions The Cisco IOS software provides a command-line interface (CLI) called the EXEC. The EXEC: • Can be accessed by dialing in with a modem • Provides access to terminal-shell services (no PPP) to do the following: –...

  • Page 82

    Integrated Modem Modem State: Ready Note The show caller command is added to the Cisco IOS software in Cisco IOS Release 11.3 AA and Release 12.0 T. If your software release does not support this command, use the show user command.

  • Page 83: Verifying The Final Running-configuration

    5 $1$ltzj$8lGJ1cGmyZRdXdPXncLAo/ resource-pool disable voice-fastpath enable ip subnet-zero no ip finger ip domain-name cisco.com ip name-server 171.69.11.48 ip name-server 171.69.2.132 ip name-server 171.69.2.133 no ip dhcp-client network-discovery Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-39 OL-3418-02 B0...

  • Page 84

    2000000 interface Async4/00 no ip address interface Async4/01 no ip address interface Async4/02 no ip address Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-40 OL-3418-02 B0...

  • Page 85: Saving Configuration Changes

    Saves the configuration changes to NVRAM so AS5400# copy running-config startup-config that they are not lost during resets, power cycles, or power outages. Step 3 Returns to enable mode. AS5400(config-if)# Ctrl-Z AS5400# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 3-41 OL-3418-02 B0...

  • Page 86: Where To Go Next

    The following publications are available on the Documentation CD-ROM that came with your gateway or on the World Wide Web from the Cisco home page, or you can order printed copies. • For additional basic configuration information, refer to Cisco IOS Dial Technologies Configuration Guide and Cisco IOS Dial Technologies Command Reference, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/index.htm.

  • Page 87: Where To Go Next

    Continuing Configuration Using the Command-Line Interface Note The information herein applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal gateways. Note that the latter requires use of Cisco IOS release 12.2(2)XB or later. This chapter continues where “Basic Configuration Using the Command-Line Interface”...

  • Page 88: Configuring Synchronous Serial Interfaces For Wan Support

    19200, 28800, 38400, 56000, 64000, 128000, and 2015232. Step 6 Changes the shutdown state to up and enables the AS5350(config-int)# no shutdown interface. Step 7 Returns to enable mode. AS5350(config-controller)# Ctrl-Z AS5350# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 89: Verify

    The channel group numbers for each CT1 controller can be arbitrarily assigned. Note Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 90: Configure

    ---text omitted--- controller t1 1/0 channel-group 0 timeslot 1-6 channel-group 1 timeslot 7 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 91: Configuring Isdn Nfas On Ct1 Pri Groups

    B channel Group identifier number for the interface under control of this D channel • Your Cisco AS5350 or Cisco AS5400 must connect to a Primary-4ess, Primary-DMS 100, or Primary-NI Note switch (see Table 3-3 on page 3-16) and must also have a channelized T1 controller and, as a result, be ISDN PRI capable.

  • Page 92: Take A Channel Or Interface Out Of Service

    E1 interface to support different types of R2 signaling, used in older analog telephone networks. The Cisco implementation of R2 signaling has DNIS support turned on by default. If you enable the ANI Note option, the collection of DNIS information is still performed. Specifying the ANI option does not disable DNIS collection.

  • Page 93: Configure

    ITU defaults), enter write term. The default setting for all countries is ITU. “Country Codes for R2 Signaling” section on page 4-9 for a list of supported countries. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 94

    AS5350(config-voiceport)# Step 10 AS5350(config-voiceport)# cptone Enter the two-digit country code to configure the contry-code regional ring tone. Step 11 AS5350(config-voiceport)# Ctrl-Z Return to enable mode. AS5350# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 95: Country Codes For R2 Signaling

    0 Slip Secs, 12 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 12 Unavail Secs Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 96: Configuring Alarms

    Redundant power supply (RPS) failure Cisco IOS software polls every second to detect the failure events that you have configured and turns on the alarm when any one of the failure events is detected. By default, the facility alarm is off. Users have to configure a facility alarm command to enable monitoring of the failure conditions.

  • Page 97: Verify

    Make sure you are using Number 12 or 14 AWG copper wires to connect to the alarm port terminal • blocks. Make sure your alarm is operational. • Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 4-11 OL-3418-02 B0...

  • Page 98: Saving Configuration Changes

    The following publications are available on the Documentation CD-ROM that came with your gateway, on the World Wide Web from the Cisco home page, or you can order printed copies. For additional basic configuration information, refer to Cisco IOS Dial Technologies Configuration •...

  • Page 99: Chapter 5 Managing And Troubleshooting The Universal Port Card

    DSPs that dynamically handle voice, dial, and fax calls. A universal port card is a hardware card that processes digital signals for the Cisco AS5350 and Cisco AS5400 universal gateways. Ports on the universal port card support multiple types of services such as modem, fax, digital data, and voice.

  • Page 100: Managing Spe Performance Statistics

    Chapter 5 Managing and Troubleshooting the Universal Port Card Managing SPE Performance Statistics The universal port card introduces slot and SPE software hierarchies. On the Cisco AS5350 and Cisco AS5400, the hierarchy designation is slot/spe and slot/port: • Slot values range from 1 to 7.

  • Page 101: Viewing Spe Performance Statistics

    Viewing SPE Performance Statistics You can view SPE statistics using the Cisco IOS software with the gateway. To view performance statistics for the universal port cards, enter one or more of the following commands in privileged EXEC...

  • Page 102

    | slot/spe summary—Displays the history statistics of all SPEs in a particular slot, specified SPE, or specified SPE range. It is used in the same way the show modem command is used for MICA modems. (The show modem command is not supported on the Cisco AS5350 or Cisco AS5400.) show spe Commands show spe log—Displays the oldest event first from the slot history event log.

  • Page 103: Managing Ports

    The example below demonstrates how to enter port configuration mode for a range of ports. AS5400# configure terminal Enter configuration commands, one per line. End with CNTL/Z. AS5400(config)# port 3/1 3/18 AS5400(config-port)# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 104: Managing Spes

    SPE firmware, performing busyout on SPEs, and clearing active calls on the SPEs. SPE Country On the Cisco AS5350 and Cisco AS5400, DS-0 companding law selection is configured for the entire system rather than on individual voice ports.

  • Page 105

    ACTIVE 0 ______ ______ 4/07 0042-0047 ACTIVE 0 ______ ______ 4/08 0048-0053 ACTIVE 0 ______ ______ 4/09 0054-0059 ACTIVE 0 ______ ______ 4/10 0060-0065 ACTIVE 0 ______ ______ Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 106: Spe Configuration Mode

    SPE state is changed to Out-of-Service. The state of the SPEs is reflected in the show spe command display. Use the no form of this command to re-enable the ports on the SPE. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 107: Troubleshooting

    Bad, this diagnostic test may take from 5 to 10 minutes to complete. You may perform additional testing on an inoperative port by executing the test port modem back-to-back command. The no port modem autotest command disables testing. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 108

    3/02 12:01:14 PM 3/95 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:01:14 PM 3/94 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:01:15 PM 3/75 Back-To-Back :STARTUP TEST Idle PASS Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-10 OL-3418-02 B0...

  • Page 109: Spe Recovery

    SPEs under maintenance are below max-spes, or until stop-time (if set), or until all SPEs marked for recovery or upgrade have had their firmware reloaded. The default download-maintenance time is 03:00. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-11...

  • Page 110: Upgrading Spe Firmware

    Unbundled from Cisco.com. This is a more up-to-date version of SPE firmware released before the next Cisco IOS release, or a special version of SPE firmware shipped with a new board. See the “Upgrading SPE Firmware from the Cisco.com FTP Server” section on page 5-14 for details.

  • Page 111: Important Upgrade Commands

    Use the show spe version command to list the versions of SPE firmware running on the SPEs, residing in system Flash memory, and bundled with Cisco IOS software. This helps you decide if you need to change the version running on the modems.

  • Page 112: Upgrading Spe Firmware From The Cisco.com Ftp Server

    You must be a registered Cisco user to log in to Cisco’s Software Center. Note You can download software from the Cisco.com FTP server using an Internet browser or using an FTP application. Both procedures are described. Using an Internet Browser Step 1 Launch an Internet browser.

  • Page 113

    LAN using a terminal emulation software application. Using an FTP Application Note The directory path leading to the SPE firmware files on cco.cisco.com is subject to change without notice. If you cannot access the files using an FTP application, try the Cisco Systems url http://www.cisco.com/cgi-bin/ibld/all.pl?i=support&c=3 Log in to the Cisco.com FTP server, called cco.cisco.com:...

  • Page 114

    Step 6 Copy the SPE firmware files from the gateway to your local environment with the get command. Step 7 Quit your terminal session: ftp> quit Goodbye. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-16 OL-3418-02 B0...

  • Page 115

    Because the SPE firmware is configurable for individual SPEs or ranges of SPEs, the Cisco IOS software automatically copies the SPE firmware to each SPE each time the gateway restarts.

  • Page 116

    0.0.6.75 SPE firmware On-Flash Firmware-Filename Version Firmware-Type ========================== ======= ============= flash:np.spe 0.6.4.5 SPE firmware flash:np_6_77.spe 0.0.6.77 SPE firmware flash:np_6_79.spe 0.0.6.79 SPE firmware flash:np-spe-upw-1.0.1.2.bin 1.0.1.2 SPE firmware Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-18 OL-3418-02 B0...

  • Page 117

    Specify when the SPE firmware upgrade is to occur. Step 7 AS5400(config-SPE)# firmware upgrade busyout | download-maintenance | reboot Step 8 Type the exit command to exit SPE config mode. AS5400(config-SPE)# exit AS5400(config)# Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-19 OL-3418-02 B0...

  • Page 118: Using Spe Firmware Bundled With Cisco Ios Software

    Use this procedure to update SPE firmware on the SPEs in your gateway if you decide to use the version of SPE firmware bundled with Cisco IOS software instead of the version already mapped to your ports. To set the SPE firmware mapping to the SPE firmware version bundled with Cisco IOS software, enter the following commands: Enter the enable command.

  • Page 119

    Flash memory are deleted; therefore save and restore any important files (for example, the Cisco IOS software image). If the new Cisco IOS image contains the same SPE firmware as the old one, no new code is downloaded Note to the SPEs.

  • Page 120: Health Monitor

    AS5400#show health-monitor summary ? Output modifiers <cr> The following example shows the display output of the show health-monitor summary command: AS5400#show health-monitor summary Chassis: Power Supply Failure Temperature Fans Memory: Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-22 OL-3418-02 B0...

  • Page 121: Interface Queue Wedge Monitor

    End with CNTL/Z. AS5400#(config)#interface-monitor enable AS5400#(config)#^Z AS5400## Step 2 Show interfaces. (In this case, some interfaces are already wedged.) AS5400##sh wedged-interfaces output Interface Name Time Since Wedge Async4/00 00:23:33 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-23 OL-3418-02 B0...

  • Page 122

    00:39:42: %HHM-3-INTFWEDGE: Virtual-Access3 Output Queue Wedged AS5400## AS5400## AS5400## Step 8 Show wedge output. AS5400##sh wedge out Interface Name Time Since Wedge Async4/00 00:25:26 Async4/01 00:25:20 Async4/02 00:25:15 Async4/03 00:25:08 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-24 OL-3418-02 B0...

  • Page 123

    Show interface wedge process running again. (No process is running now.) AS5400##sh proc cpu | i Intf AS5400## AS5400## Step 5 Show wedged interface input. (No input.) AS5400##show wedged-interfaces output Interface Time Since Wedge AS5400## AS5400## Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-25 OL-3418-02 B0...

  • Page 124

    Here is the o/p again --------------------- AS5400##sh wedged-interfaces input Interface Time Since Wedge Async4/00 00:24:14 Async4/01 00:24:06 Async4/02 00:23:42 Async4/03 00:23:37 FastEthernet0/0 12:00:44 FastEthernet0/1 12:01:01 Virtual-Access2 00:11:02 Virtual-Access3 00:11:02 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-26 OL-3418-02 B0...

  • Page 125: Where To Go Next

    • http://www.cisco.com/univercd/cc/td/doc/product/software/. Select your Cisco IOS release and search for this title. The following publications are useful for those familiar with the Cisco universal gateway products that use MICA modems. • Comparing Universal Port SPE Commands to MICA Modem Commands, available online at http://www.cisco.com/warp/customer/76/nextport_compare.html...

  • Page 126

    Chapter 5 Managing and Troubleshooting the Universal Port Card Where to Go Next Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 5-28 OL-3418-02 B0...

  • Page 127: Chapter 6 Configuring Voice Over Ip

    (voice and data) networks. Routers and switches such as the Cisco AS5350 and Cisco AS5400 universal gateways can handle origination, transport, and termination of VoIP traffic. They digitize analog voice signals, compress them, package them into a series of discrete packets, and transport them interleaved with data packets.

  • Page 128: Voip Basics

    Although VoIP technology is primarily software-based, it requires that you install a universal port card Note into the appropriate slot of your Cisco AS5350 or Cisco AS5400 universal gateway. The number of ports or channels available for sending VoIP data depends on the capacity of your card. For more information, Chapter 5, “Managing and Troubleshooting the Universal Port Card.”...

  • Page 129: Call Flow

    • Gateway participates in H.323 session across network. Processes voice signals and sends packets over network. As appropriate, • sends call-progress and other in-band signals. • Ends session. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 130: Dial Peers

    If more than one such match exists, it checks whether preferences have been assigned those peers and selects the peer with the lowest preference level. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 131

    In this west-to-east scenario, dial peers 2 and 4 are used, in that order. If Newark extension 6000 were to call San Jose extension 5000, dial peers 3 and 1 would be used, in that order. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 132: Configuring Basic Voip

    Make routing or dialing transparent to users by, for example, avoiding such inconveniences as • secondary dial tones. Contact your PBX vendor to learn how to reconfigure PBX interfaces. • Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 133: Configure Signaling On Voice Ports

    Configuring Basic VoIP Configure Signaling on Voice Ports The Cisco AS5350 and Cisco AS5400 gateways process and manage digital voice calls on the universal port card. They support voice configuration on channelized T1, E1, and T3 trunk interfaces. Your universal port card supports ISDN PRI, E1 R2, and T1 CAS digital signaling. Configure your voice ports according to signaling type.

  • Page 134: Configure Dial Peers

    The following attributes, for example, are typical in a VoIP dial peer: req-qos best-effort codec g711ulaw Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 135

    Sets resource allocation policy. Sets session [target | protocol | transport] for this peer. session Changes admin state of this peer to down (no->up). shutdown translate-outgoing Sets translation rule. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 136

    Modifies SNMP voice-peer parameters. tech-prefix Sets H.323 gateway technology prefix. Sets translation rule. translate-outgoing Sets use of Voice Activity Detection. Sets dial-peer voice-class control parameters. voice-class Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-10 OL-3418-02 B0...

  • Page 137

    2 to dial-peer voice 2, which directs calls over the PSTN; the gateway, looking for the longest exact match, finds both dial peers and then uses preference as a tie breaker among those matches. For more information, see Voice over IP for the Cisco AS5300, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Dial-Peer Configuration Table The next step in creating dial peers is to create a dial-peer configuration table.

  • Page 138: Configuring Nextport Echo Canceller Control (optional)

    Configuring Voice over IP Configuring Basic VoIP Consult the references at the end of the chapter before you create a dial-peer configuration table. See also Voice over IP for the Cisco AS5300, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Configuring Nextport Echo Canceller Control (optional) The AS5350, AS5400, and AS5400HPX Universal Gateways can detect 2100Hz tones, received in G.711 encoded VoIP packets.

  • Page 139

    : Session 0x0144 Received ANS tone 0x03 from IP *Apr 26 21:40:51.735: 00:00:14: Port Trace Event: *Apr 26 21:40:51.735: Port : 3/00 *Apr 26 21:40:51.735: Address : 0x3000000 *Apr 26 21:40:51.735: Trace Event: 0x2 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-13 OL-3418-02 B0...

  • Page 140

    00:00:08: Port Trace Event: *Apr 26 21:46:36.431: Port : 3/00 *Apr 26 21:46:36.431: Address : 0x3000000 *Apr 26 21:46:36.435: Trace Event: 0x2 *Apr 26 21:46:36.435: Data Format: ASCII Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-14 OL-3418-02 B0...

  • Page 141: Voice Qos Basics

    Cisco IOS software provides many features for optimizing QoS. Fine-tuning your network to adequately support VoIP almost certainly involves enabling some of these features. Be sure to read the sited references as you enable features, as the details of wide-scale QoS deployment are beyond the scope of this document.

  • Page 142: Enabling Qos Features For Voip

    WRED (Weighted Random Early Detection) queues traffic according to priority values that you set (you set voice traffic to critical, for example), sets different Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-16 OL-3418-02 B0...

  • Page 143

    If your voice traffic passes through a Frame Relay network, the same argument holds, but the feature is called Frame Relay IP RTP Priority (described in the third reference below). Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-17...

  • Page 144

    Protocol) on all WAN links that transport voice traffic. Configure RSVP when you configure dial peers. Do not enable RSVP in conjunction with Frame Relay traffic shaping. For more information and configuration options, see Voice over IP for the Cisco AS5300, available online http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t3/voip5300/ Call-Admission Control You can gracefully prevent calls from entering your Cisco AS5850 from the PSTN when certain resources—such as CPU, memory, and interfaces—are not available to process those calls.

  • Page 145: Fragmentation And Interleaving

    Successful traffic shaping on a Frame Relay network requires that you set not just this but many other Note QoS features. Refer to these references and the “Additional Resources” section for more information. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-19 OL-3418-02 B0...

  • Page 146: Other Bandwidth-reduction Features

    If your calls are subject to significant toll-office processing, choose PCM if you have sufficient bandwidth. It is also recommended that you employ a Cisco IOS Multimedia Conference Manager (H.323 gatekeeper) or management application such as Cisco Voice Manager to help manage these types of processes.

  • Page 147

    (so as not to incur excessive end-to-end delay) and consistently. For more information and configuration options, see Voice over IP—Per Call Bandwidth Consumption, available online at http://www.cisco.com/warp/public/788/pkt-voice-general/bwidth_consume.html Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide 6-21 OL-3418-02 B0...

  • Page 148

    Note that the trade-off for increasing jitter-buffer size is a corresponding increase in delay. Cisco’s jitter buffers are normally sized dynamically, and adaptive mode plus default buffer size should suffice. But adjust mode and size as needed. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide...

  • Page 149: Additional Resources

    – http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/5300/cfios/cfselfea/ 0044gw.htm – Monitoring Voice and Fax Services on the Cisco AS5400 Universal Gateway, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/; select your Cisco IOS release and search for this title Voice over IP for the Cisco AS5300, available online at –...

  • Page 150

    Chapter 6 Configuring Voice over IP Additional Resources – Configuring Voice over IP for the Cisco 3600 Series, available online at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/voice_c/vcprt1/ vcvoip.htm – Voice over IP for the Cisco 2600/3600 Series, available online at http://www.cisco.com/univercd/cc/td/doc/product/access/nubuvoip/voip3600/index.htm • Other websites: –...

  • Page 151: Appendix

    Configuration Using the Command-Line Interface” for step-by-step instructions. The setup script in this appendix is a typical example using a version of Cisco IOS software that may not exactly match your newly loaded software; however, message prompts are similar. Getting Started...

  • Page 152: Cisco As5350 Or Cisco As5400 With As54-dfc-ct3 And As54-dfc-108np

    The messages look similar to the following display: Note The displayed messages depend on the Cisco IOS software release and feature set you selected. The screen displays in this section are for reference only and might not exactly reflect the messages on your console.

  • Page 153

    Copyright (c) 1986-2000 by cisco Systems, Inc. Compiled Wed 23-Feb-00 22:35 by beliu Image text-base:0x60008908, data-base:0x61200000 cisco AS5400 (R7K) processor (revision L) with 65536K/131072K bytes of memory. Processor board ID JAB034608LW R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3...

  • Page 154

    These controllers enable users to dial in via ISDN or analog modems. Enter yes to allow users to dial in via ISDN or analog modems. Step 12 Do you intend to allow users to dial in? [yes]: yes Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 155

    The following line signaling types are available [a] e&m-fgb [b] e&m-fgd [c] e&m-immediate-start [d] fgd-eana [e] fgd-os [f] fxs-ground-start [g] fxs-loop-start [h] none [i] r1-itu [j] r1-modified [k] r1-turkey [l] sas-ground-start [m] sas-loop-start Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 156

    After you complete the configuration script, the setup script displays the configuration command script. Go to the “Save the Configuration File” section on page A-15. Step 26 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 157: Cisco As5350 Or Cisco As5400 With As54-dfc-8ct1 And As54-dfc-108np

    It takes a few minutes for the messages to stop. The messages look similar to the following display: The displayed messages depend on the Cisco IOS software release and feature set you selected. The Note screen displays in this section are for reference only and might not exactly reflect the messages on your console.

  • Page 158

    Copyright (c) 1986-2000 by cisco Systems, Inc. Compiled Wed 23-Feb-00 22:35 by beliu Image text-base:0x60008908, data-base:0x61200000 cisco AS5400 (R7K) processor (revision L) with 65536K/131072K bytes of memory. Processor board ID JAB034608LW R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3...

  • Page 159

    Do you want to configure ISDN switch type? [yes]: The following ISDN switch types are available: [a] primary-4ess [b] primary-5ess [c] primary-dms100 [d] primary-net5 [e] primary-ntt [f] primary-ts014 Enter the switch type [b]: Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 160

    Do you want to configure FastEthernet0/0 interface? [yes]: yes Use the 100 Base-TX (RJ-45) connector? [yes]: Full duplex mode enables simultaneous data transfer between a sending and a receiving station. Note Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 161: Cisco As5350 Or Cisco As5400 With As54-dfc-8ce1 And As54-dfc-108np

    It will take a few minutes for the messages to stop. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 162

    Getting Started The messages look similar to the following display: The displayed messages depend on the Cisco IOS software release and feature set you selected. The Note screen displays in this section are for reference only and probably will not exactly reflect the messages on your console.

  • Page 163

    The virtual terminal password is used to protect access to the router over a network interface. Enter the virtual terminal password, which is used for remote console access. Step 8 Enter virtual terminal password: guessagain Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 164

    Configuring PRI on this controller. Configuring controller E1 1/1: Configuring PRI on this controller. Configuring controller E1 2/6: Configuring PRI on this controller. Configuring controller E1 2/7: Configuring PRI on this controller. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 165: Save The Configuration File

    Press RETURN to get started! %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down <Additional messages omitted.> Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 166: Where To Go Next

    Modify the existing configuration or configure additional features with the CLI as described in the • Dial Solutions Configuration Guide, the Dial Solutions Command Reference Guide, the Cisco IOS software configuration guide, and command reference publications. See “Obtaining Documentation” on page xvi.

  • Page 167: Appendix

    A P P E N D I X ROM Monitor The information herein applies to the Cisco AS5350, Cisco AS5400, and Cisco AS5400HPX universal Note gateways. Note that the latter requires use of Cisco IOS release 12.2(2)XB or later. the first software to run when the gateway is powered-up or reset. The ROM monitor can help you isolate or rule out hardware problems encountered when installing your gateway.

  • Page 168: Rom Monitor Command Conventions

    Aliasing is often used to shorten command names or automatically invoke command options. Aliases are stored in NVRAM and remain intact across periods of no power. These are some of the set aliases: b=boot h=history i=reset r=repeat k=stack ?=help Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 169: Rom Monitor Commands

    Without an argument, this command prints a list of all aliased names with their values. For example: rommon 1 > alias r=repeat h=history ?=help b=boot ls=dir Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 170

    Flash memory. b device:—Boots the first file found in the Flash memory device. The Flash memory device specified can be either flash:, to boot the Cisco IOS software, or bootflash:, to boot the boot image in Flash memory.

  • Page 171

    Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 172

    PROM in hex list the device table list files in file system disassemble instruction stream dnld serial download a program module dram verify DRAM Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 173

    Frame 04: FP = 0x02003b00 RA = 0x00012ca6 • sync—Writes the working in-core copy of the environment variables and aliases to NVRAM so that they are read on the next reset. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 174

    16-bit CRC error checking. The xmodem transfer protocol supports a 128-byte block size and the transfer begins with a block number starting at 1, which contains file data. This is the default transfer protocol. Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 175: Appendix

    This appendix includes sample outputs of the show config command after completing the procedures in “Chapter 2, “Verifying Basic Setup”” and configuring various advanced features. The following examples are useful references for you only if you are experienced with the Cisco IOS software: •...

  • Page 176

    8 controller t1 9 controller t1 10 controller t1 11 controller t1 12 controller t1 13 controller t1 14 controller t1 15 controller t1 16 controller t1 17 controller Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 177

    1-24 controller T1 1/0:11 framing esf pri-group timeslots 1-24 controller T1 1/0:12 framing esf pri-group timeslots 1-24 controller T1 1/0:13 framing esf pri-group timeslots 1-24 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 178

    0 controller T1 1/0:25 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:26 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 179

    Serial1/0:2:23 ip address 10.1.1.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 180

    10.1.5.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 181

    72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data no fair-queue no cdp enable ppp authentication chap Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 182

    1 isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable ppp authentication chap interface Serial1/0:15:23 ip address 10.1.14.2 255.255.255.0 no ip directed-broadcast encapsulation ppp Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 183

    171.0.0.0 255.0.0.0 172.22.36.1 ip route 172.0.0.0 255.0.0.0 172.22.36.1 ip route 192.168.173.0 255.255.255.0 172.22.36.1 ip route 192.168.243.0 255.255.255.0 172.22.36.1 no ip http server logging facility local5 logging 192.168.1.137 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 184

    2/00 7/107 autoselect ppp autoselect timeout 10 logging synchronous modem InOut transport input all ntp clock-period 17179742 ntp server 192.168.6.1 scheduler allocate 10000 400 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 185: Ct3 Cas/isdn Without Radius

    2 controller t1 3 controller t1 4 controller t1 5 controller t1 6 controller t1 7 controller t1 8 controller t1 9 controller t1 10 controller t1 11 controller Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 186

    T1 1/0:9 framing esf pri-group timeslots 1-24 controller T1 1/0:10 framing esf pri-group timeslots 1-24 controller T1 1/0:11 framing esf pri-group timeslots 1-24 controller T1 1/0:12 framing esf Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 187

    T1 1/0:24 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:25 framing esf ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 1/0:26 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 188

    72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data no fair-queue no cdp enable ppp authentication chap interface Serial1/0:2:23 ip address 10.1.1.2 255.255.255.0 no ip directed-broadcast encapsulation ppp Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 189

    Serial1/0:6:23 ip address 10.1.5.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 190

    10.1.9.2 255.255.255.0 no ip directed-broadcast encapsulation ppp ip mroute-cache logging event link-status no keepalive dialer idle-timeout 72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice data Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 191

    72000 either dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable ppp authentication chap Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 192

    10.3.0.0 255.255.0.0 192.168.6.10 ip route 10.66.66.66 255.255.255.255 124.124.124.1 ip route 171.0.0.0 255.0.0.0 172.22.36.1 ip route 172.0.0.0 255.0.0.0 172.22.36.1 ip route 192.168.173.0 255.255.255.0 172.22.36.1 ip route 192.168.243.0 255.255.255.0 172.22.36.1 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 193

    2/00 7/107 autoselect ppp autoselect timeout 10 logging synchronous modem InOut transport input all ntp clock-period 17179742 ntp server 192.168.6.1 scheduler allocate 10000 400 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 194: Ct3 Without Resource Pooling

    33200 max-speed 56000 resource-pool aaa protocol local dial-tdm-clock priority 1 7/0:1 ip subnet-zero no ip domain-lookup ip host jurai 172.23.254.253 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 195

    1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:5 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:6 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 196

    T1 7/0:17 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:18 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 197

    1 interface FastEthernet0/0 ip address 192.168.18.100 255.255.255.0 no ip directed-broadcast no ip mroute-cache no keepalive duplex auto speed auto interface FastEthernet0/1 ip address 192.168.19.100 255.255.255.0 no ip directed-broadcast Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 198

    000000090200003096F80084 line con 0 exec-timeout 0 0 logging synchronous transport input none line aux 0 exec-timeout 0 0 logging synchronous transport input all line vty 0 4 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 199

    1/00 6/107 autoselect ppp autoselect timeout 10 logging synchronous modem InOut transport input all ntp clock-period 17179843 ntp server 192.168.18.1 scheduler allocate 40000 200 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 200: Ct3 Cas With Resource Pooling

    5300 limit base-size 538 limit overflow-size 18 resource 5300 speech dnis group elnino resource-pool profile service gold modem min-speed 33200 max-speed 56000 resource-pool aaa protocol local Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 201

    1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:3 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:4 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 202

    1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:16 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:17 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 203

    1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:28 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 interface FastEthernet0/0 ip address 192.168.18.100 255.255.255.0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 204

    110.1.1.0 255.255.255.0 192.168.21.10 ip route 120.1.1.0 255.255.255.0 192.168.21.10 ip route 130.1.1.0 255.255.255.0 192.168.21.10 ip route 172.22.254.253 255.255.255.255 FastEthernet0/0 no ip http server dialer dnis group callblock Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 205

    1/00 6/107 autoselect ppp autoselect timeout 10 logging synchronous modem InOut transport input all ntp clock-period 17179843 ntp server 192.168.18.1 scheduler allocate 40000 200 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 206: Two 8 T1/pri Isdn With Modems

    133 pri-group timeslots 1-24 controller T1 2/2 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 2/3 framing esf linecode b8zs cablelength short 133 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 207

    133 pri-group timeslots 1-24 controller T1 5/5 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 5/6 framing esf Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 208

    64 256 0 no cdp enable interface Serial2/1:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 209

    64 256 0 no cdp enable interface Serial5/1:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem fair-queue 64 256 0 no cdp enable Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 210

    2000000 dialer string 6151300001 dialer-group 1 async default routing async mode interactive no peer default ip address no fair-queue ppp authentication chap Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 211

    1000 in hold-queue 1000 out interface Async1/04 ip address 10.5.101.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 212

    Async1/08 ip address 10.5.105.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100008 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 213

    7150100012 dialer-group 1 async mode interactive no peer default ip address no cdp enable ppp authentication chap interface Async1/13 ip address 10.5.110.1 255.255.255.0 no ip directed-broadcast encapsulation ppp Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 214

    Async1/17 ip address 10.5.114.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 215

    1/21 7/107 router eigrp 100 network 192.168.10.0 ip local pool ip-pool 10.4.1.1 10.4.1.250 ip default-gateway 192.168.10.1 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 216

    3/00 4/107 autoselect ppp script dialer dial logging synchronous modem InOut transport input all line 6/00 7/107 autoselect ppp script dialer dial logging synchronous modem InOut transport input all Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 217

    Appendix Two 8 T1/PRI ISDN with Modems exception core-file coredump exception protocol ftp exception dump 172.23.254.253 ntp clock-period 17179873 ntp server 192.168.10.1 scheduler allocate 4000 200 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 218: Two 8 E1/pri Isdn With Modems

    E1 6/2 pri-group timeslots 1-31 controller E1 6/3 pri-group timeslots 1-31 controller E1 6/4 pri-group timeslots 1-31 controller E1 6/5 pri-group timeslots 1-31 controller E1 6/6 pri-group timeslots 1-31 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 219

    64 256 0 clockrate 2000000 interface Serial0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown clockrate 2000000 interface Serial6/0:15 no ip address no ip directed-broadcast Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 220

    Serial6/7:15 no ip address no ip directed-broadcast isdn switch-type primary-net5 isdn incoming-voice modem fair-queue 64 256 0 no cdp enable interface Serial7/0:15 no ip address no ip directed-broadcast Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 221

    Serial7/7:15 no ip address no ip directed-broadcast isdn switch-type primary-net5 isdn incoming-voice modem fair-queue 64 256 0 no cdp enable interface Async1/00 ip unnumbered FastEthernet0/0 no ip directed-broadcast Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 222

    100 network 192.168.13.0 ip default-gateway 192.168.13.1 ip classless no ip http server line con 0 exec-timeout 0 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 223: Two 8 T1/pri Cas With Modems

    133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 2/2 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 224

    133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 3/3 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 225

    2000000 interface Serial0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown clockrate 2000000 interface Async1/00 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 226

    InOut transport input all line 4/00 7/107 exec-timeout 0 0 autoselect ppp script dialer dial logging synchronous modem InOut transport input all Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 227

    Appendix Two 8 T1/PRI CAS with Modems exception core-file coredump exception protocol ftp exception dump 223.255.254.253 ntp clock-period 17179726 ntp server 192.168.10.1 scheduler allocate 40000 400 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 228: Two 8 T1/pri Cas With Radius (aaa) And Resource Pooling

    0 resource group3 speech dnis group default resource-pool profile discriminator not_allowed call-type speech dnis group not_allowed !dial-tdm-clock priority 1 2/0 !ip subnet-zero Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 229

    133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 2/6 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 230

    133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 controller T1 3/7 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1-24 type e&m-fgb cas-custom 0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 231

    Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 232

    InOut transport input all exception core-file coredump exception protocol ftp exception dump 172.23.254.253 ntp clock-period 17179726 ntp server 192.168.10.1 scheduler allocate 40000 400 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 233: Two 8 T1/pri Isdn With Radius (aaa) And Resource Pooling

    0 resource group3 speech dnis group default resource-pool profile discriminator not_allowed call-type speech dnis group not_allowed ! dial-tdm-clock priority 1 2/4 ! ip subnet-zero Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 234

    T1 2/6 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 2/7 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-24 controller T1 5/0 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 235

    FastEthernet0/1 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache shutdown duplex auto Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 236

    64 256 0 no cdp enable interface Serial2/5:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 237

    64 256 0 no cdp enable interface Serial5/5:23 no ip address no ip directed-broadcast isdn switch-type primary-5ess isdn incoming-voice modem Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 238

    1000 out interface Async1/02 ip address 10.5.99.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout 2000000 dialer string 7150100002 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 239

    7150100005 dialer-group 1 async default routing async mode interactive no peer default ip address no fair-queue ppp authentication chap hold-queue 1000 in hold-queue 1000 out interface Async1/06 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 240

    10.5.107.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100010 dialer-group 1 async mode interactive ppp authentication chap Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 241

    7150100014 dialer-group 1 async mode interactive no peer default ip address no cdp enable ppp authentication chap interface Async1/15 ip address 10.5.112.1 255.255.255.0 no ip directed-broadcast encapsulation ppp Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 242

    Async1/19 ip address 10.5.116.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout AS5400 dialer string 7150100019 dialer-group 1 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 243

    10.5.1.113 255.255.255.255 Async1/16 ip route 10.5.1.114 255.255.255.255 Async1/17 ip route 10.5.1.115 255.255.255.255 Async1/18 ip route 10.5.1.116 255.255.255.255 Async1/19 ip route 10.5.1.117 255.255.255.255 Async1/20 no ip http server Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 244

    InOut transport input all exception core-file coredump exception protocol ftp exception dump 223.255.254.253 ntp clock-period 17179873 ntp server 192.168.10.1 scheduler allocate 4000 200 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 245: Two 8 E1/pri Isdn With Radius (aaa) And Resource Pooling

    0 resource group3 speech dnis group default resource-pool profile discriminator not_allowed call-type speech dnis group not_allowed spe country united-kingdom Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 246

    E1 7/3 pri-group timeslots 1-31 controller E1 7/4 pri-group timeslots 1-31 controller E1 7/5 pri-group timeslots 1-31 controller E1 7/6 pri-group timeslots 1-31 controller E1 7/7 pri-group timeslots 1-31 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 247

    FastEthernet0/0 no ip directed-broadcast encapsulation ppp async mode interactive ppp authentication chap <text omitted> interface Async5/106 ip unnumbered FastEthernet0/0 no ip directed-broadcast encapsulation ppp async mode interactive Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 248

    66666 dialer-list 1 protocol ip permit line con 0 exec-timeout 0 0 transport input none speed 9600 line aux 0 line vty 0 4 login Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 249: Ct3 With Resource Pooling, Aaa, And Modem

    4700 limit base-size 110 limit overflow-size 18 resource 4700 speech resource-pool profile customer 5300 limit base-size 538 limit overflow-size 18 resource 5300 speech dnis group elnino Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 250

    T1 7/0:6 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:7 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 251

    1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:19 framing esf ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis cas-custom 1 controller T1 7/0:20 framing esf Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 252

    192.168.18.100 255.255.255.0 no keepalive duplex auto speed auto hold-queue 4000 out interface FastEthernet0/1 ip address 172.22.35.71 255.255.0.0 shutdown duplex auto speed auto interface Serial0/0 no ip address shutdown Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 253

    000000090200003096F80084 snmp-server community public RW radius-server host 192.168.1.137 auth-port 1645 acct-port 1646 radius-server host 192.168.1.138 auth-port 1645 acct-port 1646 radius-server retransmit 2 radius-server timeout 9 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 254

    0 4 password lab no logging synchronous line 1/00 6/107 autoselect ppp autoselect timeout 10 logging synchronous modem InOut transport input all Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide OL-3418-02 B0...

  • Page 255: I N D E X

    ROM monitor CLI, see command line interface break key (interrupt) clocking Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-1 OL-3418-02 B0...

  • Page 256

    3-20 configuring local AAA security dual compressions 6-20 confreg command dual encodings 6-20 congestion management IP RTP priority 6-17 low-latency queuing (LLQ) 6-17 resource reservation (RSVP) 6-18 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-2 OL-3418-02 B0...

  • Page 257

    ISDN D channels gateway line speed 1-13 configuring 3-23, 4-5 group-async interfaces for VoIP 6-7, 6-8 group-range command IP address 3-24 NFAS backup D channel 3-24, 4-5 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-3 OL-3418-02 B0...

  • Page 258

    6-18 no ip source-route command 3-36 LLQ, see low-latency queuing note symbol, meaning of login banner loopback low-latency queuing (LLQ) 6-17 online copy of guide Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-4 OL-3418-02 B0...

  • Page 259

    R2 signaling show port operational-status command show privilege command See signaling repeat command show process cpu command reset command show process cpu history command Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-5 OL-3418-02 B0...

  • Page 260

    3-27 performance statistics POTS dial-peer configuration commands configuring sample dial peers viewing show version command field descriptions Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-6 OL-3418-02 B0...

  • Page 261

    Series 6-24 upgrading to a new Cisco IOS release 1-10 Configuring Weighted Fair Queuing 6-17 URL locations, Cisco websites Dial Technologies Command Reference 3-13 URLs Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-7 OL-3418-02 B0...

  • Page 262

    VoIP over Frame Relay with Quality of Service (Fragmentation, Traffic Shaping, IP RTP Priority 6-19 Weighted Fair Queueing (WFQ) 6-17 voice-activity detection (VAD) 6-22 voice encoding (codecs) 6-20 voice-fastpath command 6-16 Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide IN-8 OL-3418-02 B0...

This manual also for:

As5400

Comments to this Manuals

Symbols: 0
Latest comments: