Download Print this page

Advertisement

Cisco AS5350XM and Cisco AS5400XM Universal Gateways
INCLUDING LICENSE AND WARRANTY
1
Cisco 90-Day Limited Hardware Warranty Terms
2
Documents, Equipment, and Tools
3
Install Chassis
4
Install Modules
5
Connect Cables
6
Power Up the Universal Gateway
7
Perform Initial Configuration
8
Slot Numbering
9
Obtaining Documentation
10
Documentation Feedback
11
Cisco Product Security Overview
12
Obtaining Technical Assistance
13
Obtaining Additional Publications and Information
Quick Start Guide

Advertisement

   Related Manuals for Cisco AS5400XM

   Summary of Contents for Cisco AS5400XM

  • Page 1

    Cisco AS5350XM and Cisco AS5400XM Universal Gateways INCLUDING LICENSE AND WARRANTY Cisco 90-Day Limited Hardware Warranty Terms Documents, Equipment, and Tools Install Chassis Install Modules Connect Cables Power Up the Universal Gateway Perform Initial Configuration Slot Numbering Obtaining Documentation Documentation Feedback...

  • Page 2: Cisco 90-day Limited Hardware Warranty Terms

    Cisco 90-Day Limited Hardware Warranty Terms There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com.

  • Page 3: User Documentation

    All of the documents described here are available online and on the Documentation DVD. To be sure of obtaining the latest information, you should access the online documentation. The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Note To access online user documentation: From Cisco.com at http://www.cisco.com, choose Technical Support &...

  • Page 4

    You can access these documents at Technical Support & Documentation > Product Support > Cisco IOS Software > Cisco IOS Software Release you are using > Release Notes. Items Included with Cisco AS5350XM and Cisco AS5400XM Universal Gateways • 19-inch (48.26-cm) and 24-inch (60.96-cm) rack-mount kits •...

  • Page 5: Safety Information

    Install Chassis The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Note Safety Information For safety information you need to know before working on your Cisco universal gateway, see the Regulatory Compliance and Safety Information document that accompanied this device.

  • Page 6

    The chassis may be installed with either the front panel or the back panel facing forward. Note Figure 3 Cisco AS5350XM Universal Gateway Bracket Installation—Front Panel Forward (19-Inch Rack) Figure 4 Cisco AS5400XM Universal Gateway Bracket Installation—Front Panel Forward (19-Inch Rack)

  • Page 7

    Installing the Cisco AS5350XM Universal Gateway in a Rack (19-Inch Rack) Figure 6 Installing the Cisco AS5400XM Universal Gateway in a Rack (19-Inch Rack) Desktop Installation For desktop or shelf mounting, use the rubber “feet” shipped on a black adhesive strip with the chassis. They protect the chassis and provide a nonskid surface.

  • Page 8: Chassis Ground Connection

    Cisco AS5350XM Universal Gateway Ground Lug Attachment Ground lug attachment Figure 8 Cisco AS5400XM Universal Gateway Ground Lug Attachment Connect the other end of the ground wire to a suitable grounding point at your site. Step 4 Ground lug attachment...

  • Page 9: Install Modules

    If you are not installing additional carrier cards or feature cards, proceed to the “Connect Cables” section on page 15. For additional information about installing carrier cards and feature cards, see the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide.

  • Page 10

    Figure 10 Install the Carrier Card in the Cisco AS5400XM Universal Gateway Align the captive screws with their holes, and seat the card completely. Step 4 Tighten the two captive screws to secure the carrier card to the chassis. (See Figure 11 and Figure 12.)

  • Page 11

    For configuration details, see the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide. The Cisco AS5350XM and Cisco AS5400XM universal gateways does not support the mixing of T1 and E1 feature Note cards in the same chassis.

  • Page 12

    Figure 15 Installing a Feature Card in a Cisco AS5400XM Universal Gateway Align the captive screws with their holes, and seat the card completely. Step 3 Tighten the screws to secure the feature card to the chassis. (See Figure 16 and Figure 17.)

  • Page 13

    Table 1 LEDs Feature Card T1 or E1 ACTIVITY (ACT) feature card OK/MAINT • Remote Alarm (RA) • Local Alarm (LA) • Loopback (LB) State Description Fast flicker (green) The feature card is up and running. Slow flicker (green) The feature card is not yet fully functional. Green The feature card has passed initial power-up diagnostics tests and is operating normally.

  • Page 14

    Table 1 LEDs (continued) Feature Card CT3 feature ACTIVITY (ACT) card OK/MAINT M13 Alarm (MA) Remote Alarm (RA) Local Alarm (LA) T3 EN/DIS Low signal (LOS) Network Loop (LOOP) Universal ACTIVITY (ACT) port and OK/MAINT dial-only feature card State Description Fast flicker The feature card is up and running.

  • Page 15: Connect Cables

    OK/MAINT 1. To display information about an M13 alarm, use the show controllers t3 user EXEC command. Connect Cables The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Note System Management and Power Connections The connections described here provide electrical power and management access.

  • Page 16

    You can use the auxiliary port to connect a terminal or a modem for remote access to the universal gateway. To connect a terminal (an ASCII terminal or a PC running terminal emulation software) to the console port on a Cisco AS5350XM or Cisco AS5400XM universal gateway, follow this procedure. Step 1 Connect the terminal to the console port by using an RJ-45 rollover cable and an RJ-45-to-DB-25 or RJ-45-to-DB-9 adapter.

  • Page 17

    Figure 19 Connecting the Cisco AS5400XM Universal Gateway to a Console Terminal Console port (RJ-45) RJ-45-to-RJ-45 rollover cable Configure your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity, and 1 stop bit. To Step 2 configure the console port, see the Guide .

  • Page 18: Connect To An Ethernet Network

    Figure 20 Connecting the Cisco AS5350XM Universal Gateway to an Ethernet Hub GE1 10/100/1000BASE-T port Ethernet hub Straight-through Ethernet cable Figure 21 Connecting the Cisco AS5400XM Universal Gateway to an Ethernet Hub GE1 10/100/1000BASE-T port Ethernet hub Straight-through Ethernet cable...

  • Page 19

    Statement 87 You can connect the Cisco AS5350XM and Cisco AS5400XM universal gateways to a WAN in the following ways: • Connect each T1/PRI port to an RJ-45 jack with a straight-through RJ-45-to-RJ-45 cable. (See Figure 22, Figure 23, and Figure 24.)

  • Page 20

    RJ-45-to-RJ-45 cable Note For other T1 cabling options, see the card installation guide for the Cisco AS5350XM and Cisco AS5400XM universal gateways. You can access this document at Technical Support & Documentation > Product Support > Universal Gateways and Access Servers > Cisco AS5300 or Cisco AS5400 Series Universal Gateways > Install and Upgrade Guides.

  • Page 21

    Statement 90 Figure 25 Connecting a 2-Port or 4-Port Feature Card on the Cisco AS5350XM Universal Gateway to an RJ-45 Jack Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software RJ-45 jack E1 cable...

  • Page 22

    Connecting an 8-Port Feature Card on the Cisco AS5350XM Universal Gateway to an RJ-45 Jack T1/E1 8 PRI connector E1 cable Figure 27 Connecting an 8-Port Feature Card on the Cisco AS5400XM Universal Gateway to an RJ-45 Jack T1/E1 8 PRI connector E1 cable RJ-45 jack...

  • Page 23

    Connecting a Channelized T3 Feature Card on the Cisco AS5350XM Universal Gateway to a T3 CSU/DSU T3 cables Figure 29 Connecting a Channelized T3 Feature Card on the Cisco AS5400XM Universal Gateway to a T3 CSU/DSU T3 DFC T3 cables...

  • Page 24

    (DB-26) Serial transition cable EIA/TIA-232, EIA/TIA-449, EIA/TIA-530A, EIA/TIA-530, V.35, or X.21 connector Figure 31 Connecting a Serial Port on the Cisco AS5400XM Universal Gateway to a CSU/DSU Synchronous serial port (DB-26) Serial transition cable EIA/TIA-232, EIA/TIA-449, EIA/TIA-530A, EIA/TIA-530, V.35, or X.21 connector...

  • Page 25

    • Use a coaxial cable to connect a timing signal generator (TSG) to the building integrated timing supply (BITS) port. The BITS port is used for external clocking. (See Figure 32.) Figure 32 Connecting the Cisco AS5350XM and Cisco AS5400XM Universal Gateways to a TSG BITS port connector •...

  • Page 26

    Connecting an Alarm Device to the Cisco AS5350XM Universal Gateway To alarm device Figure 34 Connecting an Alarm Device to the Cisco AS5400XM Universal Gateway Cable ties Step 4 Attach two cable ties to the chassis, and connect the wires to the cable ties.

  • Page 27: Connect Ac Power

    Connect AC Power To connect AC power, follow these steps: Step 1 Connect the black power cable to the receptacle on the power supply at the back of the universal gateway. (See Figure 35, Figure 36, and Figure 37.) Figure 35 Connecting the AC Power Cable to the Cisco AS5350XM Universal Gateway Single Power Supply If you are using the Cisco AS5350XM redundant power supply, use the special power cable that came with your Note...

  • Page 28: Connect Dc Power

    Figure 37 Connecting the AC Power Cables to the Cisco AS5400XM Universal Gateway Connect the other end of the power cable to the electrical outlet. Step 2 If your universal gateway has a redundant power supply installed, repeat Step 1 and Step 2 for the second power supply.

  • Page 29

    Note the orientation of the DC power supply. The power supply cord should have three wires: 48 VDC Return, Step 2 –48 VDC, and a safety ground (green wire). (See Figure 38, Figure 39, and Figure 40.) Warning The illustration shows the DC power supply terminal block. Wire the DC power supply using the appropriate lugs at the wiring end, or with no lugs, as illustrated.

  • Page 30

    DC connector A - A + B - B + Source A - NEG Source A - RTN Source B - NEG Figure 40 Cisco AS5400XM Universal Gateway DC Power Supply Connections Mounting screws Terminal block IN OK LEDs IN OK...

  • Page 31: Power Up The Universal Gateway

    Power up the universal gateway. The internal power supply fan should power up. Step 8 Power Up the Universal Gateway The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Note Checklist for Power Up You are ready to power up the Cisco universal gateway if the following steps have been completed: •...

  • Page 32

    It takes a few minutes for the messages to stop. A Cisco AS5350XM or Cisco AS5400XM universal gateway with the maximum number of packet voice data Note modules, version 2 (PVDM2) modules installed can take up to six minutes to boot from power-on to system ready.

  • Page 33: Perform Initial Configuration

    Configuration Guide for your Cisco IOS software release. Perform Initial Configuration The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways. Note At this point you can continue, using the setup command facility, or you can configure the universal gateway manually using the command-line interface (CLI).

  • Page 34

    When the following message appears, enter no to configure all interfaces: Step 2 Note that, if you enter yes, your system will not be configured correctly. Note Basic management setup configures only enough connectivity for management of the system. Extended setup will ask you to configure each interface on the system.

  • Page 35

    Configure Vines? [no]: Configure XNS? [no]: Configure Apollo? [no]: Configure bridging? [no]: Async lines accept incoming modems calls. If you will have users dialing in via modems, configure these lines. Configure Async lines? [yes]: Async line speed [115200]: Will you be using the modems for inbound dialing? [yes]: Would you like to put all async interfaces in a group and configure them all at one time ? [yes]: Allow dial-in users to choose a static IP address? [no]:...

  • Page 36

    Step 13 Enter yes to configure the Gigabit Ethernet 0/0 interface to connect the gateway to a LAN, and then respond to the remaining questions to configure the Fast Ethernet port: Do you want to configure GigabitEthernet0/0 Configure IP on this interface? [no]: yes IP address for this interface: 172.22.50.10 Subnet mask for this interface [255.255.0.0] : 255.255.255.128 Class B network is 172.22.0.0, 25 subnet bits;...

  • Page 37

    Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Step 6 Change the name of the gateway to a meaningful name: Router(config)# hostname Gateway Gateway(config)# Step 7 Create a secret password. This password provides access to privileged EXEC mode. Substitute your enable secret password for guessme.

  • Page 38: Configuring Local Aaa Security

    AAA (called triple A) is the Cisco IOS security model used on all Cisco devices. AAA provides the primary framework through which you set up access control on the Cisco AS5350XM or Cisco AS5400XM universal gateway. The same authentication method is used on all interfaces. AAA is set up to use the local database configured on the gateway.

  • Page 39

    After you have configured AAA security, all access will require a username and password. Make sure that your Caution login name and password are working before you exit or reboot. If you are unable to get back into your universal gateway, see the password recovery instructions at the following URL: http://www.cisco.com/warp/public/474/pswdrec_as5300.shtml Gateway# login...

  • Page 40: Configuring The Asynchronous Group Interface

    In this example: • Interface loopback 0—Identifies the universal gateway with a unique and stable IP address. One unique IP address from a common block of addresses is assigned to each device in the IP network. This technique makes security-filtering easy for the Network Operations Center (NOC).

  • Page 41

    Define the slot/port group range of the interface. The range that you specify depends on the number of asynchronous Step 4 interfaces you have on your gateway. If your gateway has 108 asynchronous interfaces, you can specify group-range 1/1 1/107. Gateway(config-if)# group-range slot/port slot/port Building configuration...

  • Page 42

    Configuring a T1 or E1 Feature Card This section shows how to configure a T1 or E1 feature card. On a Cisco AS5350XM or Cisco AS5400XM universal gateway, you can allocate the available channels for channelized T1 and E1 in the following ways: •...

  • Page 43

    Define the line code. Step 5 • For the CT1 controller, use binary 8 zero substitution (B8ZS): Gateway(config-controller)# linecode b8zs • For the CE1 controller, use high-density bipolar 3 (HDB3): Gateway(config-controller)# linecode hdb3 Return to privileged EXEC mode: Step 6 Gateway(config-controller)# Ctrl-Z Gateway# To save the gateway configuration, save it to NVRAM.

  • Page 44

    Use the enable command and password to enter privileged EXEC mode. You are in privileged EXEC mode when the Step 1 prompt changes to Gateway# Gateway> enable Password: password Gateway# Enter global configuration mode. You are in global configuration mode when the prompt changes to Step 2 Gateway# configure terminal Enter configuration commands, one per line.

  • Page 45: Configuring Isdn Pri

    0 C-bit Coding Violation, 0 P-bit Err Secs 0 P-bit Severely Err Secs, 0 Severely Err Framing Secs 0 Unavailable Secs, 0 Line Errored Secs 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs Total Data (last 32 15 minute intervals): 0 Line Code Violations, 0 P-bit Coding Violation, 0 C-bit Coding Violation, 0 P-bit Err Secs, 0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,...

  • Page 46

    Slot 0 is reserved for the motherboard. The feature card slots are numbered sequentially from 1 to 3 for the Cisco AS5350XM universal gateway and from 1 to 7 for the Cisco AS5400XM universal gateway. Port numbering is from 0 to 7, depending on the WAN feature card installed.

  • Page 47

    For CE1 ISDN PRI—If you do not specify the time slots, the specified controller is configured for 30 B channels Note and 1 D channel. B channel numbers range from 1 to 31; channel 16 is the D channel for E1. Corresponding serial interface numbers range from 0 to 30.

  • Page 48

    0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 Your Cisco AS5350XM or Cisco AS5400XM universal gateway supports a total of 248 ISDN channels per ingress Note feature card.

  • Page 49: Configuring The D Channels For Isdn Signaling

    framing esf channel-group 20 timeslots 1-24 speed 64 controller T1 1/0:12 framing esf channel-group 20 timeslots 1-24 speed 64 controller T1 1/0:13 framing esf channel-group 20 timeslots 1-24 speed 64 controller T1 1/0:14 framing esf channel-group 20 timeslots 1-24 speed 64 controller T1 1/0:15 framing esf channel-group 20 timeslots 1-24 speed 64...

  • Page 50

    Figure 41 Relationship of ISDN PRI Components for T1 Channel Time slot type number (data channel) (data channel) (data channel) (data channel) • • • • • • • • • • (data channel) (data channel) (data channel) (signaling channel) Note When you configure your CT1 controller for a Non-Facility Associated Signaling (NFAS) backup D channel, a serial interface is automatically created only when your primary D channel fails.

  • Page 51

    Return to privileged EXEC mode: Step 6 Gateway(config-if)# ctrl-z Gateway# To save the gateway configuration, save it to NVRAM. See the “Saving Configuration Changes” section on page 60. Verifying D Channel Configuration To verify your D channel configuration, enter the show interface serial command and make sure that the line protocol is up and that you are using the correct IP interface.

  • Page 52: Spe Firmware

    SPE firmware is automatically downloaded to universal port or dial-only feature cards from the Cisco AS5350XM or Cisco AS5400XM universal gateway when you boot the system for the first time or when you insert a universal port or dial-only feature card while the system is operating. When you insert feature cards while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.

  • Page 53

    The modem speed 115200 bps and hardware flow control are the default settings for integrated modems. Note To configure the lines and ports to allow users to dial in to your network, follow these steps: Use the enable command and password to enter privileged EXEC mode. You are in privileged EXEC mode when the Step 1 prompt changes to Gateway#...

  • Page 54

    SPE settings: ============== Country code configuration: default T1 (u Law) Polling interval: 8 secs. History log events: 50(per port) Port legends: ============ Port state: (s)shutdown (t)test (r)recovery (d)download (b)busiedout (p)busyout pending, (B)bad (a)active call Call type: (m)modem (d)digital (f)fax-relay (v)voice (_)not in use System resources summary: ====================== Total ports: 108, in use ports: 0, disabled ports: 0, free ports: 108...

  • Page 55

    • DSPware is bundled into the Cisco IOS image, but the DSPware is also supported as a standalone firmware image that can be loaded on the DSP (independent of the Cisco AS5350XM or Cisco AS5400XM universal gateway image). • Software-configurable G.168-compliant echo cancellation for tail circuits up to 64 milliseconds.

  • Page 56

    4.4.5 Configure Clocking The time-division multiplexing (TDM) bus on a Cisco AS5350XM or Cisco AS5400XM universal gateway backplane can receive an input clock from one of four basic sources on the universal gateway: • A T1 or E1 feature card •...

  • Page 57: External Clock

    External Clock The TDM bus can be synchronized with an external clock source that can be used as an additional network reference. If no clocks are configured, the system uses a primary clock through a software-controlled default algorithm. If you want the external T1/E1 clock (through the BITS interface) as the primary clock source, you must configure it using the dial-tdm-clock priority CLI command;...

  • Page 58

    In the following example, a trunk clock from an 8 PRI CT1 feature card is set at priority 2 and uses slot 4 and ds1 port (controller) 6: Gateway(config)# dial-tdm-clock priority 2 4/6 Gateway(config)# exit In the following example, a trunk clock from a CT3 feature card is set at priority 2 and uses slot 1, ds3 port 0, and ds1 port 19: Gateway(config)# dial-tdm-clock priority 2 1/0:19 Gateway(config)# exit In the following example, the free-running clock is set at priority 3:...

  • Page 59

    Trunk cards controllers clock health information ------------------------------------------------ 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 Slot Port Type 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 G G G G G G G G G G G G G G G G G G G G G G G G G G G G CLOCK CHANGE HISTORY --------------------------...

  • Page 60: Voice Over Ip

    Source Slot Port DS3-Port Trunk Trunk Trunk cards controllers clock health information Slot Type 7 6 5 4 3 2 1 0 B B B B G G G G CLOCK CHANGE HISTORY CLOCK Event External Change in CLI configuration Gateway# The most common cause of clock slip problems is an improperly set dial-tdm-clock priority parameter.

  • Page 61: Where To Go Next

    For additional specialized configuration procedures, see the appropriate Cisco IOS software configuration documentation on the Documentation DVD and on Cisco.com. For detailed configuration information specific to the Cisco AS5350XM and Cisco AS5400XM Universal Gateway: Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide.

  • Page 62: Obtaining Documentation

    Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/techsupport...

  • Page 63: Ordering Documentation

    Cisco.com. You can submit comments about Cisco documentation by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.

  • Page 64: Obtaining Technical Assistance

    Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT: •...

  • Page 65: Obtaining Additional Publications And Information

    For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com • Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources.

  • Page 66

    You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj • Networking products offered by Cisco Systems, as well as customer support services, can be obtained at this URL: http://www.cisco.com/en/US/products/index.html • Networking Professionals Connection is an interactive website for networking professionals to share questions, suggestions, and information about networking products and technologies with Cisco experts and other networking professionals.

  • Page 68

    Slovakia • Slovenia • South Africa • Spain • Sweden • Switzerland • Taiwan • Thailand • Turkey • Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar,...

This manual also for:

As5350xm

Comments to this Manuals

Symbols: 0
Latest comments: