Cisco AS5400XM Installing Manual
Hide thumbs
Also See for AS5400XM:
- Installation manual (104 pages) ,
- Quick start manual (69 pages) ,
- Regulatory compliance and safety information manual (68 pages)
Advertisement
Quick Links
Installing the Cisco AS5400XM Universal
Gateway
This chapter guides you through the installation of the Cisco AS5400XM universal gateway and includes
the following sections:
•
•
•
•
•
•
•
Warning
Only trained and qualified personnel should be allowed to install or replace this equipment.
Statement 49
Warning
This equipment is intended to be grounded. Ensure that the host is connected to earth ground during
normal use. Statement 39
Incorrect connection of this or connected equipment to a general purpose outlet could result in a
Warning
hazardous situation. Statement 87
Setting Up the Chassis
You can set the chassis on a desktop or install it in a rack. Use the procedure in this section that best
meets the needs of your network:
•
•
OL-6418-02
Setting Up the Chassis, page 3-1
Connecting to the Network, page 3-5
Connecting to the BITS Port, page 3-10
Connecting to the Alarm Port, page 3-11
Supplying Power, page 3-12
Where to Go Next, page 3-15
Setting the Chassis on a Desktop
Rack-Mounting the Chassis
C H A P T E R
Cisco AS5400XM Universal Gateway Chassis Installation Guide
3
3-1
Advertisement
Related Manuals for Cisco AS5400XM
Summary of Contents for Cisco AS5400XM
-
Page 1: Table Of Contents
C H A P T E R Installing the Cisco AS5400XM Universal Gateway This chapter guides you through the installation of the Cisco AS5400XM universal gateway and includes the following sections: Setting Up the Chassis, page 3-1 • Connecting to the Network, page 3-5 •... -
Page 2: Setting Up The Chassis
Attach the rubber feet as shown in Figure 3-1. Rubber feet are included in the accessory kit that shipped with your Cisco AS5400XM universal gateway. Figure 3-1 Attaching the Rubber Feet Universal gateway chassis bottom Cisco AS5400XM Universal Gateway Chassis Installation Guide OL-6418-02... - Page 3 Setting Up the Chassis Rack-Mounting the Chassis This section describes how to rack-mount the chassis. The Cisco AS5400XM universal gateway arrives with 19-inch (48.26-cm) rack-mount brackets and larger brackets for use with a 23- (58.42-cm) or 24-inch (60.96-cm) rack. (See Figure 3-2.)
- Page 4 To install the chassis, follow these steps: Step 1 Attach the brackets as follows with the standard brackets on the side panels of the Cisco AS5400XM universal gateway and either the front panel forward or the rear panel forward, as shown in...
-
Page 5: Connecting To The Network
Statement 1001 Caution If the Cisco AS5400XM universal gateway is configured with fewer than seven DFCs, make sure that a blank slot cover is installed over each open slot to ensure proper airflow. The Cisco AS5400XM universal gateway arrives with all carrier cards and DFCs already installed, Note unless you order a card separately as a spare. -
Page 6: Connecting To A Wan
To comply with the intra-building lightning surge requirements of GR-1089-CORE, Issue III, October Caution 2002, you must use a shielded cable when connecting to either of the Cisco AS5400XM universal gateway Ethernet ports. The cable must consist of shielded cable terminated by shielded connectors on both ends, with the cable shield material tied to both connectors. - Page 7 To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Warning You can connect the Cisco AS5400XM universal gateway to a WAN in the following ways: Use a breakout cable and straight-through RJ-45-to-RJ-45 cable for CT1 connections. (See •...
- Page 8 EIA/TIA-530, V.35, or X.21 connector For cable and port pinouts for specific dial feature cards, see Appendix C, “Cabling Note Specifications,” in the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide. Cisco AS5400XM Universal Gateway Chassis Installation Guide OL-6418-02...
-
Page 9: Connecting The Console Terminal And Modem
Connecting the Console Terminal and Modem Use the console terminal for local administrative access to the Cisco AS5400XM universal gateway. You can only connect a terminal to the console port. You can use the auxiliary port to connect a terminal or a modem for remote access. -
Page 10: Connecting To The Bits Port
Configure your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity, and Step 2 2 stop bits. To configure the console port, see the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide. Connecting a Modem to the Auxiliary Port To connect a modem to the auxiliary port, follow these steps: Connect a modem to the auxiliary port using an RJ-45 rollover cable with an RJ-45-to-DB-25 adapter. -
Page 11: Connecting To The Alarm Port
Connect the alarm port only to a safety extra-low voltage (SELV) source using 22 AWG, or thicker, copper wire. SELV ratings are maximum 30 volts AC (RMS), maximum 60 volts DC, and maximum 50 VA power. The alarm port is rated for 2.0-amp maximum current. Cisco AS5400XM Universal Gateway Chassis Installation Guide 3-11 OL-6418-02... -
Page 12: Supplying Power
Cisco AS5400XM universal gateway. A single-point ground is recommended at the power distribution rack. The grounding architecture for the Cisco AS5400XM universal gateway is isolated DC return (DC-I). Note Do not touch the power supply when the power cord is connected. For systems with a power switch,... - Page 13 Step 4 The internal power supply fan should power up. Wiring the DC Power Supply If you ordered the Cisco AS5400XM universal gateway with a DC power supply, follow the procedure in this section to wire the terminal block. Note The grounding architecture for the Cisco AS5400XM universal gateway is isolated DC return (DC-I).
- Page 14 Figure 3-15 DC Power Supply Connections Mounting screw Mounting screw Strain-relief clamps IN OK DC OK LEDs Terminal block On/off switch IN OK DC OK LEDs Terminal block Mounting screw Strain-relief clamps Cisco AS5400XM Universal Gateway Chassis Installation Guide 3-14 OL-6418-02...
-
Page 15: Where To Go Next
The internal power supply fan should power up. Where to Go Next When you power up the Cisco AS5400XM universal gateway for the first time, messages begin to appear on your console screen. See the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide for configuration instructions. - Page 16 Chapter 3 Installing the Cisco AS5400XM Universal Gateway Where to Go Next Cisco AS5400XM Universal Gateway Chassis Installation Guide 3-16 OL-6418-02...