Kyocera KM-3035 Operation Manual page 110

Section 5 OTHER CONVENIENT FUNCTIONS
2 Select how you want the copy sets to be finished by touching
the "Staple mode" key, the "Saddle Stitch" ["Center Staple" ]
key or the "Punch mode" key, as appropriate.
Follow the instructions on the right side of the touch panel
and verify the direction in which the originals were set.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Finished
Offset
Off
On
Metric specifications
Ready to Job build.
Set original. Press Start key.
Finished
Group
Group
Off
None
1 set
1 set
IMPORTANT!
If the designation for the direction that the originals are set is not
correct, copying may be accomplished incorrectly.
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
5 Making copies at an enlarged or reduced magnification ratio
This procedure selects the magnification ratio of the finished copies.
1 With the content of the "Basic" tab displayed, touch the
"Reduce/Enlarge" key. The "Reduce/Enlarge" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1 sided
11x8 1 / "
2
Select
Original
paper type
Offset AMS
Reduce
Finished
/Enlarge
Basic Quality
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build -Step 1
1-sided
Select
Original
paper
type
Group AMS
Reduce/
Finished
Enlarge
Basic Quality
5-64
Back
Staple Punch Check direction
Check direction of
No cover No cover
original top side.
Staple Punch
mode mode
None
Saddle
Stitch
Rear
Back
Staple Punch Check direction
Check direction of original.
Staple Punch
Mode Mode
None
Center
Staple
Back Edge
1 sided copy
1 sided/
2 sided
1 sided copy-Left
Back Edge
Finished page #:0
Orig. set
direction
Edit
1-sided Copy
1-sided/
2-sided
1-sided Copy-Left
Back Edge
Finished page #: 0
Orig. set
direction
Edit
2 Select the desired magnification ratio.
If you want to have the copy magnification ratio selected
automatically, touch the "AMS" key.
If you want to manually set the magnification ratio, touch the
"# keys" ["#-Keys"] key and then enter the desired ratio with
the keypad, or touch the "+" key or the "-" key to change the
displayed magnification ratio to the desired setting in 1%
Set
increments.
You can also select the magnification ratio by touching the
Close
preset zoom ratio keys at the right that corresponds to the
desired ratio.
Inch specifications
Ready to Job build.
Left top
corner
Place originals then press Start key.
Reduce/Enlarge
Set
Standard
Zoom
XY Zoom
Close
Metric specifications
Ready to Job build.
Left top
corner
Set original. Press Start key.
Reduce/Enlarge
Standard
Zoom
XY Zoom
Metric specifications (Asia Pacific)
Ready to Job build.
Set original. Press Start key.
Reduce/Enlarge
Standard
Zoom
XY Zoom
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
Set
End
Insert
page
Set
End
Insert
blank page
Back
(25 400)
154 %
100 %
AMS
5 1 / x8 1 / "R8 1 / x14"
2 2 2
129 %
100 %
8 1 / x11" R11x17"
2
121 %
400 %
8 1 / x14" R8 1 / x17"
2 2
78 %
200 %
# keys
8 1 / x14" R8 1 / x11"
5 1 / x8 1 / "R11x17"
2 2
2 2
Back
(25~400)
141% A 4➔A3
100 %
AMS
A 5➔A4
100% 127%
Folio➔A3
400% 106%
11x15"➔A3
200% 90%
#-Keys
A 5➔A 3 Folio➔A4
Back
(25~400)
141% A 4➔A 3
100 %
AMS
B 5➔B 4
A 4➔B 4
100% 122%
A 5➔B 5
400% 115% B 4➔A 3
B 5➔A 4
200% 86%
A 3➔B 4
#-Keys
A 5➔A 3 A 4➔B 5
Set
Close
77 %
11x17" R8 1 / x14"
2
64 %
11x17" R8 1 / x11"
2
50 %
11x17" R5 1 / x8 1 / "
2 2
25 %
Set
Close
75%
11x15"➔A 4
70% A3➔A4
A4➔A5
50%
25%
Set
Close
81%
B 4➔A 4
B 5➔A 5
70% A 3➔A 4
B 4➔B 5
50%
25%