Version Numbers Of Compatible Programming Tools; Assignment Of Input/Output Numbers; Assignment Of Input Numbers - Mitsubishi MELSEC-F FX3U Series User Manual

FX /FX Series PLC User's Manual - Positioning Control Edition
3U 3UC
Built-in Positioning Function
1.4

Version Numbers of Compatible Programming Tools

The Built-in positioning function depends on the version of the FX
optimum version number to create programs.
1) FX PLC
3U
Version
number of FX
PLC
Ver.2.00 or later
*1. Depending on the version of GX Developer, the model selection may be set to FX
2) FX PLC
3UC
Version number
of FX
3UC
Ver.1.00 or later
Ver.1.30 or later
Ver.2.00 or later
*1. Depending on the version of GX Developer, the model selection may be set to FX
1.5

Assignment of Input/Output Numbers

1.5.1

Assignment of Input Numbers

Assign the input numbers of the FX
Application
Stop command
Zero return
command
Near-point
signal
(DOG)
Zero-phase
signal
ABS read
B - 8
→ For details on version numbers of compatible PLCs, refer to Section 1.3.
Model
3U
(Software model)
GX Developer
SW D5C-GPPW-J
SW D5C-GPPW-E
Model
PLC (Software model)
GX Developer
SW D5C-GPPW-J
SW D5C-GPPW-E
/FX
3U
Input number
All input Connect the line to any input.
points If the line-connected input is turned on, turn off the positioning instruction signal.
All input Connect the line to any input.
points If the line-connected input is turned on, turn on DSZR or ZRN instruction signal.
Connect the line to the input of the near-point signal (DOG) specified by DSZR or
ZRN instruction.
→ For details on the near-point signal of DSZR instruction, refer to Section
All input
Point:
points
• To use DSZR instruction:
If X000 to X017 of the main unit are set for the near-point signal (DOG), the
near-point signal (DOG) will be monitored at 1ms intervals.
• To use ZRN instruction:
If X000 to X007 of the main unit are set for the near-point signal (DOG), the
interruption function will be used for processing of the near-point signal (DOG).
Connect the line to the input (X000 - X007) specified for the zero-phase signal (this
X000 to 007
input is specified by DSZR instruction).
Connect the line if it is necessary to use the absolute position detection system.
All input
Connect the line to the input specified by the ABS instruction.
points
Use 3 consecutive input points for this function.
1.4 Version Numbers of Compatible Programming Tools
3U
Version number of
compatible GX Developer
Ver. 8.23Z or later
Version number of
compatible GX Developer
Ver.8. 1 3P or later
Ver.8. 1 8U or later
Ver.8.23Z or later
PLC as follows:
3UC
Remarks
→ For details on the near-point signal of ZRN instruction, refer to
/FX PLC. Select a PLC having
3UC
Remarks
• Supports FX PLCs (Ver.2.00 or later).
3U
Model selection: FX3U(C)
3UC
Remarks
• Supports FX PLCs (Ver.1.00 or later).
3UC
Model selection: FX
3UC
• Supports FX PLCs (Ver.1.30 or later).
3UC
Model selection: FX
3UC
• Supports FX PLCs (Ver.2.00 or later).
3UC
Model selection: FX3U(C)
3UC
1 Outline
*1
.
*1
.
6.2.
Section 6.3.