Index - Mitsubishi Electric MELSEC-QD75MH1 User Manual

INDEX

[Number]
1-axis fixed-feed control ................................ 9-44
1-axis linear control (ABS linear 1) ............... 9-27
1-axis linear control (INC linear 1) ................ 9-28
1-axis speed control ...................................... 9-68
2-axis circular interpolation control with sub point
designation (ABS circular sub) ..................... 9-54
2-axis circular interpolation control with sub point
designation (INC circular sub) ...................... 9-57
2-axis circular interpolation control with center
point designation (ABS circular right/ABS
circular left) .................................................... 9-62
2-axis circular interpolation control with center
point designation (INC circular right/INC
circular left) .................................................... 9-65
2-axis fixed-feed control (interpolation)
....................................................................... 9-46
2-axis linear interpolation control (ABS linear 2)
....................................................................... 9-29
2-axis linear interpolation control (INC linear 2)
....................................................................... 9-31
2-axis speed control ...................................... 9-71
3-axis fixed-feed control (interpolation) ........ 9-48
3-axis linear interpolation control (ABS linear 3)
....................................................................... 9-33
3-axis linear interpolation control (INC linear 3)
....................................................................... 9-36
3-axis speed control ...................................... 9-74
4-axis fixed-feed control (interpolation) ........ 9-52
4-axis linear interpolation control (ABS linear 4)
....................................................................... 9-39
4-axis linear interpolation control (INC linear 4)
....................................................................... 9-42
4-axis speed control ...................................... 9-78
[A]
ABS direction in degrees (
Absolute position detection system (
Absolute system ............................................ 9-15
Acceleration time 0 (
Acceleration time 1 (
Acceleration time 2 (
Acceleration time 3 (
Cd.40
)............ 5-168
Pr.103
Pr.9
) ......................... 5-28
Pr.25
) ....................... 5-38
Pr.26
) ....................... 5-38
Pr.27
) ....................... 5-38
Acceleration time No. (
Acceleration/deceleration process selection
Pr.34
(
Acceleration/deceleration processing function
......................................................................12-86
Acceleration/deceleration time change during
speed change, enable/disable selection (
......................................................................5-154
Acceleration/deceleration time change function
......................................................................12-52
Acceleration/deceleration time change program
........................................................................6-45
Actual acceleration/deceleration time ...........5-28
Adaptive tuning mode(
Adaptive vibration suppression control/low pass
filter (
Pr.125
Address (
AFTER mode ...............................................12-70
Allowable circular interpolation error width
Pr.41
(
Analog monitor output 1 (
Analog monitor output 2 (
Analog monitor 1 offset (
Analog monitor 2 offset (
Applicable system ............................................2-6
Applicable wire size .........................................3-3
Arc address (
Auto tuning (
Automatic trapezoidal acceleration/deceleration
processing method ......................................12-87
Axis display LED ..............................................4-3
Axis error No. (
Axis error occurrence (Hour) (
Axis error occurrence (Minute: second) (
......................................................................5-124
Axis error reset (
) 5-62
Axis feed rate (
Axis in which the error occurred (
......................................................................5-124
Axis in which the warning occurred (
......................................................................5-126
Axis monitor data .........................................5-128
Index - 1
Da.3
)......................5-92
) ........................................................5-40
).....................5-68
Pr.119
).................................................5-70
Da.17
) .......................................5-115
) ........................................................5-44
Pr.172
Pr.173
Pr.174
Pr.175
Da.7
) ...................................5-100
).....................................5-62
Pr.108
Md.10
Md.23
,
Cd.5
) ..............................5-150
Md.28
) ..............................5-132
Cd.12
)
) ................5-80
) ................5-82
) .................5-84
) .................5-84
).........5-124, 128
Md.11
) ......5-124
Md.12
)
Md.9
)
Md.14
)