Warrior Iii Instrument Cluster - Oil Temperature, Fuel Pressure, And Oil Pressure Gauge; Exhaust Gas Probe Installation; Removal Of Slip Ring End Bearing; Removal Of Drive End Head - Piper CHEROKEE WARRIOR PA-28-151 1995 Maintenance Manual

PIPER CHEROKEE WARRIOR SERVICE MANUAL
Figure
9-1. PA-28-151 and PA-28 -161, Warrior II Fuel System Diagram ...........................................................
9-2. PA-28 -161, Warrior III Fuel System Diagram....................................................................................
9-3. Tolerances, Union Nut and Tubing Nut...............................................................................................
9-4. Resistance Decade Test Box Set Up....................................................................................................
9-5 Warrior III Fuel Quantity Needle Deviation........................................................................................
9-6. Fuel Quantity Transmitter Checking Jig..............................................................................................
9-7. Fabricated Fuel Quantity Transmitter Checking Jig............................................................................
9-8. Locking Fuel Cap.................................................................................................................................
9-9. Fuel Filter Bowl and Screen.................................................................................................................
9-10. Plunger Fuel Pump...............................................................................................................................
9-11. Engine Primer.......................................................................................................................................
10-1. PA-28-151, Warrior and PA-28-161, Warrior II Vacuum Pump.........................................................
10-2. PA-28-161, Warrior III Vacuum Pump................................................................................................
10-3. Warrior I and II Instrument Panel (Typical) ........................................................................................
10-4. Warrior III VFR Instrument Panel (Typical) .......................................................................................
10-5. Warrior II and III Auxiliary Vacuum System Installation...................................................................
10-6. Warrior II and III Auxiliary Vacuum Electrical Schematic.................................................................
10-7. Pitot and Static Air Systems.................................................................................................................
10-8.

Warrior III Instrument Cluster - Oil Temperature, Fuel Pressure, and Oil Pressure Gauge................

10-9. Warrior III Fuel Quantity Gauge..........................................................................................................
10-10.

Exhaust Gas Probe Installation ............................................................................................................

11-1. Exploded View of Prestolite and Electrosystems Alternators .............................................................
11-2. Lamp Bank Load..................................................................................................................................
11-3. Removal of Rectifier............................................................................................................................
11-4.

Removal of Slip Ring End Bearing......................................................................................................

11-5.

Removal of Drive End Head................................................................................................................

11-6. Removal of End Head Bearing.............................................................................................................
11-7.

Testing Rotor for Grounds ...................................................................................................................

11-8. Testing Rotor for Shorts.......................................................................................................................
11-9. Installation of Bearing..........................................................................................................................
11-10. Installation of Rectifier.........................................................................................................................
11-11. Terminal Assembly..............................................................................................................................
11-12. Slip Ring End Bearing Assembly.........................................................................................................
11-13. Testing Alternator ................................................................................................................................
11-14. Brush Installation .................................................................................................................................
11-15. Internal Wiring Diagram......................................................................................................................
11-16. Exploded View of Chrysler Alternator ................................................................................................
11-17. Checking Chrysler Alternator Field Current Draw..............................................................................
11-18.

Testing Chrysler Alternator Field Circuit............................................................................................

11-19. Chrysler Alternator Rectifier End Shield and Stator Assembly...........................................................
11-20. Testing Positive Rectifiers With C-3829 Tester ..................................................................................
11-21. Testing Negative Rectifiers With C-3829 Tester.................................................................................
11-22. Testing Positive Rectifiers With Test Lamp........................................................................................
11-23. Testing Negative Rectifiers With Test Lamp.......................................................................................
11-24.

Rectifier and Heat Sink Assembly Removal........................................................................................

11-25. Rectifier End Shield Assembly............................................................................................................
11-26. Testing Stator .......................................................................................................................................
11-27. Removal of Pulley................................................................................................................................
11-28. Removal of Bearing .............................................................................................................................
Revised: February 28, 1995
LIST OF ILLUSTRATIONS
2A6
Island Enterprises
Aerofiche
Grid No.
2A13
2A14
2A16
2A20
2A20
2A22
2A23
2A24
2B1
2B3
2B5
2B16
2B16
2B17
2B18
2C1
2C2
2C6
2C18
2C20
2C24
2E4
2E5
2E6
2E6
2E7
2E7
2E7
2E7
2E9
2E9
2E10
2E10
2E10
2E11
2E11
2E14
2E16
2E17
2E18
2E19
2E19
2E20
2E20
2E21
2E21
2E22
2E22
2E22