Wiring Diagrams; Board Connectors; Terminal Descriptions; Table 12: Board Connector Descriptions - Bosch Solution 16i Installation Manual

Solution 16i
Installation Manual

B O A R D CO N N E C TO R S
T
he following table lists the various sockets, pin headers
and switches located on the panel and their functions.
Connector
This socket allow you to connect a service
Service
Keypad to the panel during installation.
This socket is used to connect the cabinet
Tamper
tamper switch to the panel.
This push button is used to reset the con-
Default trol panel back to factory default and to
enable Direct Link Programming Mode.
Voice
This is used to connect the optional Voice
Module
Command Module (CM101B).
This socket is used to connect the Direct
Direct Link Link Interface (P/N CM900B) or the Flash
Port
Programmer Interface (P/N CM901) to the
panel.
This is a RJ12 6P/4C connector that allows
Telco
you to connect the control panel to the
PSTN telephone line.
Expansion
Used to connect addition modules to the
Port control panel. eg TCP/IP interface.
LAN Term Used to terminate the RS485 LAN.

Table 12: Board Connector Descriptions

T E R M I N A L D E S C R I P T I O N S
Nº Name
Earth wire from this terminal is
1 Earth
connected to the Mains earth.
2 ~ (AC) Connection of the 16-18V AC 50-60 Hz
3 ~ (AC) adapter or internal transformer.
4 BAT (-) Negative and positive connections to
5 BAT (+) the stand-by battery. 12 VDC / 7.2AH
6 +12 V
These terminals are used to power
7 +12 V
detectors and other accessory devices.
8 GND
(750mA Fused)
9 GND
10 LAN + These terminals are used to power LAN
11 LAN - modules and devices. (750 mA Fused)
Connect the LAN A data terminal of any
LAN device (eg. Keypads, expansion
12 LAN A boards) to this terminal. The control
panel supports up to 300 m of 24/0.20
(18 AWG) wire on these terminals.
Connect the LAN B data terminal of any
LAN device (eg. Keypads, expansion
13 LAN B boards) to this terminal. The control
panel supports up to 300 m of 24/0.20
(18 AWG) wire on these terminals.
Common positive terminal for system
14 COMM+ outputs. This terminal is 2.5A PTC Fuse
protected.
3-2

Wiring Diagrams


Description
Description
Nº Name
15 OUT 1 Fully supervised programmable, open
16 OUT 2 collector outputs capable of driving
17 OUT 3 (sink) loads up to 1 amp for sirens,
18 OUT 4 strobes etc.
Programmable Input for RF Receivers,
19 INPUT
Keyswitch and other devices.
20 ZN 1 Zone 1 and 9 sensor loop input (+).
21 GND Common (-) for Zone 1 & 2 sensor loop.
22 ZN 2 Zone 2 and 10 sensor loop input (+).
23 ZN 3 Zone 3 and 11 sensor loop input (+).
24 GND Common (-) for Zone 3 & 4 sensor loop.
25 ZN 4 Zone 4 and 12 sensor loop input (+).
26 ZN 5 Zone 5 and 13 sensor loop input (+).
27 GND Common (-) for Zone 5 & 6 sensor loop.
28 ZN 6 Zone 6 and 14 sensor loop input (+).
29 ZN 7 Zone 7 and 15 sensor loop input (+).
30 GND Common (-) for Zone 7 & 8 sensor loop.
31 ZN 8 Zone 8 and 16 sensor loop input (+).
32 IN These terminals are used to connect the
33 IN telephone line from the street.
34 OUT These terminals are used to connect the
35 OUT premises telephones.

Table 13: Terminal Block Descriptions and Functions

Description
Bosch Security Systems 09/11 BLCC500I