While every effort has been taken the accuracy of this document, outside of the enclosure during installation. neither Bosch Security Systems Pty Ltd nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged...
Zone Name ...................17 Walk Test All Zones ..............17 Walk Test A Single Zone ............17 Outputs ................. 18 Output Status................18 Turn Output On/Off ..............18 Output Name ................19 External Siren Test ..............19 Internal Siren Test ...............19 Strobe Test ..................19 Bosch Security Systems 03/10 BLCC100U...
5-5-9 Email Options 7-6-0 Name 7-6-1 Start Stop Dates Periodic Test 5-9-0 Send Test Report System Options 7-7-3 Keypad Hi/Lo Temp 7-7-7 Site Name System Testing 7-9-0 Walk Test All Zones 7-9-1 Battery Test Table 1: Control Panel Menu Tree Bosch Security Systems 03/10 BLCC100U...
Part zones. Zones A ‘Zone’ is a detection device, or group of devices connected to your security system. Zones are identified by the area they monitor, such as a front door, bedroom window or hallway. Bosch Security Systems 03/10 BLCC100U...
A fire alarm is active Flashing The [] key allows you to navigate through No fire alarm menus or to toggle characters when programming telephone numbers. Fire alarm in memory (Turn the area All On and Off to Clear). Bosch Security Systems 03/10 BLCC100U...
4 fast short beeps Tone followed by a 5 second pause (repeat). Key Pressing any key on the keypad sounds one Press short beep, indicating that the key press is Tone accepted. Bosch Security Systems 03/10 BLCC100U...
PIN followed by the [OFF] key. at 6:55pm. Therefore the system will automatically turn All On at 7:00pm. 4. When exit time has expired, the keypad will display the Part On icon. 5. To turn the system off, enter your PIN, then press [OFF]. Bosch Security Systems 03/10 BLCC100U...
[OK], or press [MENU] to exit without saving. The following additional special characters are available scrolling using down arrow keys. 3. Enter your new PIN, and then press [OK]. If an error tone + - @ # $ “ & % * : ( ) / < > = Bosch Security Systems 03/10 BLCC100U...
Press , OK or MENU reader to turn the system or specific areas on and off. 2. Use the [] and [] keys to select the user that you want to add a PIN, then press [OK] to select. Alternatively, you can enter the user number you want Bosch Security Systems 03/10 BLCC100U...
This menu allows a Master user the ability to identify a token which has been programmed into the system. Only tokens that have been assigned to the same area(s) as the Master user cn be identified. Bosch Security Systems 03/10 BLCC100U...
Multiple schedules can be linked to the same timer group. Time Groups User 1 Name Press OK to SAVE There are 8 different timer groups available. 3. Use the [] and [] keys to scroll the cursor left and right Timer Group Example across the user name text. Use the [] and [] keys to 1. To set up a timer group you need to select an unused scroll through the different characters available. To clear timer group number from 1 to 8, in this example we will all text from the cursor position to the right, press the assume timer group number to be 5. [OFF] key. Bosch Security Systems 03/10 BLCC100U...
Armed All On 1. Enter [MENU] + [1] + [4] + [5] and select the user from the list then press [OK]. Ur001 John Smith If the area is turned Part On, the keypad will display: Ur002 Debbie Smith Ur003 User 3 Name Press OK or MENU Main Office A001 Armed Part On 2. Use the up and down arrow keys to highlight the Access Group then press the [ON] key to select or the [OFF] key to deselect. 3. To exit, press [OK]. Bosch Security Systems 03/10 BLCC100U...
Enter programming mode (PIN + MENU) then, 1. Enter [MENU] + [2] + [0] + [5]. A list of different areas will display on the keypad. Area icons will only display if programmed to A001 Reception Area do so by your security installer. A002 Sales Dept Note A003 Administration Dept Press OK or MENU Bosch Security Systems 03/10 BLCC100U...
16 zones. Plus When the optional radio receiver is fitted any available zone may press OFF. be programmed as a wireless zone. Your installer will advise you Press OK or MENU Bosch Security Systems 03/10 BLCC100U...
Inputs > Commands > Zone Chime is ON. Smoke Sensor Reset MENU 3-0-5 To turn OFF, Press OFF. This menu allows you to reset smoke sensors. To Go Back Press OK Enter programming mode (PIN + MENU) then, Bosch Security Systems 03/10 BLCC100U...
This menu allows you to test all zones within an area at the same 3. Open and close the zone that needs to be tested. time. To successfully walk test each zone, you must open and When the zone has been successfully faulted and close each zone. restored, the keypad will display: Enter programming mode (PIN + MENU) then, 1. Press [MENU] + [3] + [9] + [0]. The keypad will display a list of areas that are available to walk test zones. Bosch Security Systems 03/10 BLCC100U...
Press OK or MENU To Turn OFF,Press OFF. To Go Back Press OK The keypad will display the following when the output is ON and OK: To turn the output off, press [OFF]. Output 1 Name O001 Is ON and Ready 4. Press [OK] to save and exit, or press [MENU] to exit without saving. Press OK or MENU The keypad will display the following when the output is ON and missing: Bosch Security Systems 03/10 BLCC100U...
If the system has been partitioned, the keypad will External Audible display a list of areas. Testing Press any key to A001 Area 1 Name abort A002 Area 2 Name Press OK or MENU A003 Area 3 Name PRESS OK or MENU When the siren test is complete, the keypad will display the following: Bosch Security Systems 03/10 BLCC100U...
If the control panel has been configured to report via Call Forward On/Off domestic format, the keypad will display information for Call Forward is ON, telephone number 1. To turn OFF, Press OFF. To Go Back Press OK Domestic Phone Number 1 631728_ 2. To toggle call forward on, press the [ON] key or press the Press 0-9 OK to SAVE [OFF] key to turn call forward off. Bosch Security Systems 03/10 BLCC100U...
For other countries please substitute the appropriate commands after consultaion with your telephone company. 2. Using the numeric keys, enter all the digits of the call Enter programming mode (PIN + MENU) then, forward off sequence. You can change a single digit by scrolling the cursor left [] and right []. For special characters (eg. , = pause, * 1. *61 (To turn Call Forward On – After Time). or # etc), use the [] and [] keys. 2. Telephone number that you want calls to go to (e.g. 3. Press [OK] to save and exit, or press [MENU] to exit 0416123456). without saving. 3. *5# (End of Call Forward sequence after 5 seconds). Bosch Security Systems 03/10 BLCC100U...
When entering an email address the @ symbol is represented keypad display To Go Back Press OK Note To enter this character press the 1 key repeatedly until the symbol appears in the display. If the test is successful, the keypad will prompt: Bosch Security Systems 03/10 BLCC100U...
This menu allows you to adjust the volume of the keypad’s buzzer. desired backlight is reached. Each keypad will need to have their volume adjusted separately. 3. Press [OK] to save and exit, or press [MENU] to exit Enter programming mode (PIN + MENU) then, without saving. 1. Press [MENU] + [6] + [1] + [0]. The keypad will display: Bosch Security Systems 03/10 BLCC100U...
E001 Mon,01Oct 03:41 S1L2 2. If viewing system trouble conditions, the keypad will Manual Test Report display similar to the following: Press OK or MENU Panel 001 P001 Voltage= 13.9V Temp=36 2. Use the [] and [] keys scroll between history events. Date And Time 3. Press [OK] or [MENU] to exit. Press OK or MENU The third line of the keypad display scrolls between all current system trouble events. Bosch Security Systems 03/10 BLCC100U...
Page 25
The system memory has reset to factory default. You should contact your security company. Service Mode The security installer has entered service mode. Phone In Use The system is using the phone line. Table 7: Control Panel Trouble Messages Bosch Security Systems 03/10 BLCC100U...
Sk002 Schedule 2 Name press [OK]. Sk003 Schedule 3 Name Press OK or MENU The keypad will display the following: 2. Use the [] and [] keys to select the schedule that you Name S001 want to change, then press [OK] to select. Alternatively, you can enter the schedule number, then press [OK]. Schedule 1 Name The keypad will display the following: PRESS OK to SAVE 3. To program the schedule name, use the [] and [] keys to scroll the cursor left and right across the user Bosch Security Systems 03/10 BLCC100U...
At any time you can use the [] and [] keys to scroll through Press OK to SAVE the complete list of available characters. To clear all text from the cursor position to the right, press 3. To program the holiday start date and stop date, use the [OFF] key. the [] and [] keys to scroll the cursor left and right Bosch Security Systems 03/10 BLCC100U...
The battery test can take up to two minutes to complete and the keypad will display the voltage of the battery during the test. Enter programming mode (PIN + MENU) then, 1. Press [MENU] + [7] + [9] + [2]. The keypad will display the battery voltage whilst under test: Bosch Security Systems 03/10 BLCC100U...
Solution16 User Guide Plus I n s t a l l at i on Details INSTALLED BY: DATE PHONE: FAX: EMAIL: SERVICE PHONE: FAX: EMAIL: MONITORED BY: PHONE: FAX: EMAIL: WARRANTY EXPIRES: NOTES: Bosch Security Systems 03/10 BLCC100U...
Page 30
Customer ................ 22 DTMF Quick Arm ..............9 Remote Arming ..............9 Email Address ..............22 RF Keyfob Email Options ..............22 Add 11 Delete .................. 12 Features ................5 Fire Alarm ................6 Schedules Bosch Security Systems 03/10 BLCC100U...
Page 31
Name .................. 12 User PIN .................. 8 Voice Setup ............... 20 Walk Test All Zones ................ 17, 28 Web Email ................20 Zone 24-Hour Zones ................ 5 Bypass Command .............. 15 Chime .................. 16 Non 24-Hour Zones .............. 5 Part 2 Zones ................ 16 Bosch Security Systems 03/10 BLCC100U...