Display Telephone Line Fail; Report Telephone Line Fail; Alarm On Telephone Line Fail If Armed; Alarm On Telephone Line Fail If Disarmed - Bosch Solution 16plus Installation Manual

Solution 16
plus Installation Manual

i
Software Version 1.02 and higher will now continue to display
Telco Line Fail in alarm memory after the siren outputs time
out. Previous software revisions would no longer display on the
Note
keypad that the Telco line failed once the siren run time expired.

Display Telephone Line Fail

This option sets the panel to display a trouble signal on the keypad
display when the panel detects a teleco line fail condition.

Report Telephone Line Fail

This option sets the panel to send a line fail report when it detects a
telco line fail condition. If configured, the panel is able to report this
signal via an alternative reporting method such as the GSM cellular
network.
If no alternative route exists then the panel will send the signal and
restore when the PSTN line is reconnected.

Alarm On Telephone Line Fail If Armed

This option sets the panel to trigger an alarm when the telco line
fails provided that the area is turned All On or Part On. In a multi-area
system this option is global and will be triggered if only one area in
the system is in the armed state. The alarm will continue to sound
until a valid PIN is entered or the siren timer expires.

Alarm On Telephone Line Fail If Disarmed

This option sets the panel to trigger an alarm when the telco line
fails provided that the area is turned OFF or disarmed. In a multi-area
system this option is global and will be triggered if only one area in
the system is in the disarmed state. The alarm will continue to sound
until a valid PIN is entered or the siren timer expires.

Display 'Phone In Use'

This option allows the keypad to display Phone In Use when the
telephone line has been looped by the control panel for either
incoming or outgoing calls. If this option is disabled, no indication is
provided on the keypad.
i
The dialler status indicator LED located on the main panel will
always show the status of the dialler. See Section 3 - Wiring
Diagrams for more information.
Note
Comms > Properties >

Country

0 = Australia
1 = New Zealand 6 = Portugal
2 = Italy 7 = Hungary
3 = Greece 8 = Czech Republic
4 = Cyprus 9 = Poland
5 = Spain 10 = Bulgaria
This menu automatically sets the dialling parameters including
dial and busy tones etc. for the country the panel is working in.
(*** System Wide Parameter ***)
Press [MENU] + [5] + [2] + [3]. The keypad will display the
1)
currently selected country. The default country is Australia.
2) Use the up and down arrow keys to select the appropriate
country then Press [OK].
9-6
Comms Programming

MENU 5-2-3

0
11 = China
12 = Hong Kong
13 = Malaysia
14 = Brazil
15 = Reserved
Ln001 AUSTRALIA
Ln002 NEW ZEALAND
Ln003 ITALY
Press  OK or MENU
3) Press [OK] to confirm and save and exit or press [MENU] to exit
without saving.
WARNING: Press OK to set
dialler to
AUSTRALIA
i
For correct dialler operation, you must make sure that the correct
country selection is made for your location. If your country is not
listed here please contact your Digiflex distibutor.
Note
Comms > Properties >

Set SMS Password

p a s s w d
This menu sets the SMS password which is required whenever
SMS reporting is selected. The password will typically be defined
by the service provider or Telco carrier who you are using to
route the message.
By default the SMS password is set to suit the Telstra Network
in Australia.
1) Enter [MENU] + 5+2+7. The keypad will display the current SMS
password.
2) Use the arrow and number keys to move and change text.
When the password is complete, press [OK]. At any time you
can press the [OFF] key to clear the text from the current cursor
position to the end of the line.
SMS Pager Password
passwd
Press  OK to SAVE
i
See Alpha Text Programming in Section 4 - Programming
Overview for further detail on entering alpha text.
Note
Comms > Remote Access >

Call Back Number

1
This menu sets the call back telephone number which can be
used to establish a SolutionLink RAS connection to the panel for
remote programming. The remote computers modem should
be connected to this number and Solutionlink should be set to
wait for an incomming call.
The installer or customer can force the panel to dial this number
by entering MENU 5-0-1.
MENU 5-2-7

MENU 5-3-0

Digits
Bosch Security Systems 05/10 BLCC100I
32