Bosch Solution 16plus Installation Manual page 100

Solution 16
plus Installation Manual

System > Commands >
Service Mode
This command allows the installer to put the panel into service
mode before performing system maintenance or upgrades.
When in service mode, the following functions are disabled. By
default, service mode will automatically terminate after 2 hours
if not terminated sooner by the installer.
™ Zone Tamper
™ Alarm Outputs
™ Dialler
™ Panel Tamper
1) Press [MENU] + [7] + [0] + [8]. The keypad will display the
current service mode status.
Service Mode
Service Mode is OFF,
To turn ON, Press ON.
Press OK or MENU
To turn service mode on, press [ON], or press [OFF] to turn
2)
service mode off.
3) Press [OK] or [MENU] to exit when finished.
i
Service mode will automatically exit after 2 hours if set to do so in
MENU 7-7-4 — Installer Options.
Note
SYSTEM CLO CK
System > Clock >
Set Date & Time
This menu allows you to set or adjust the panels internal clock.
1) Press [MENU] + [7] + [1] + [0]. The keypad will display the
current date and time.
Set Date And Time
01-Jan-2004 04:37am
Press  OK to SAVE
2) Use the left, right, up and down arrow keys to set the day,
month, year, hour and minute. Use left and right keys to scroll
the cursor left and right to between the month, day, year, hour
and minute.
3) When the time is set correctly press [OK] to save and exit or
press [MENU] to exit without saving.
11-4
System Programming

MENU 7-0-8

-
MENU 7-1-0
 
System > Clock >
Summertime On
- -
At 2:00am Month
This menu allows you to program when day light savings start
during the year. This will allow the panel to automatically adjust
it's built in clock accordingly. In Australia, daylight savings moves
forward one hour at 2:00 am on the last Sunday of October.
To program Summertime On, you will need to set the month of
the year (Jan to Dec), the week of the month (1 to 5) and the day
of the week (Sun to Sat) that daylight savings starts.
(*** System Wide Parameter ***)
1) Press [MENU] + [7] + [1] + [1]. The keypad will display the
current Summertime on.
Summertime On
Month Week Day
--- ---
Press  OK to SAVE
Use the up and down arrow keys to toggle the month, week
2)
and year. Use the left and right keys to move the cursor
between the month, week and year.
When finished press [OK] to save and exit or press [MENU] to
3)
exit without saving.
System > Clock >
Summertime Off
- -
At 3:00am Month
This menu allows you to program when day light savings end
during the year. This will allow the panel to automatically adjust
it's built in clock accordingly. In Australia, daylight savings
moves backwards one hour at 3:00 am on the last Sunday of
March.
To program Summertime Off, you will need to program the
month of the year (Jan to Dec), the week of the month (1 to 5)
and the day of the week (Sun to Sat) that daylight saving ends.
(*** System Wide Parameter ***)
1) Press [MENU] + [7] + [1] + [2]. The keypad will display the
current Summertime off.
Summertime Off
Month Week Day
--- ---
Press  OK to SAVE
2) Use the up and down arrow keys to toggle the month, week
and year. Use the left and right keys to move the cursor
between the month, week and year.
3) When finished press [OK] to save and exit or press [MENU] to
exit without saving.
MENU 7-1-1

- - - - -
Week
---
MENU 7-1-2

- - - - -
Week
---
Bosch Security Systems 05/10 BLCC100I
- -
Day
- -
Day