Bosch Solution 16plus Installation Manual page 46

Solution 16
plus Installation Manual

Areas > Commands >
Turn All Areas On
This command allows you to turn on all areas that your PIN has
been assigned to at the same time. An alternative method for
arming all areas is to enter your PIN then press and hold the
[ON] key for 2 seconds.
1) Enter [MENU] + [2] + [0] + [2]. The keypad will display the exit
time bar to prompt you to exit all areas. You should leave all
areas now.
2) When exit time has expired, the keypad will display that all
areas are turned All On (Armed).
Area 1 Name
EXIT NOW
i
The Display Area Icons option is programmable per keypad. If
this option has not been selected then Area icons 1 to 4 will not
be displayed. See Menu 6-1-4 — Display Area Icons.
Note
Areas > Commands >
Turn All Areas Off
This command allows you to turn off all areas that your PIN has
been assigned to at the same time. This command cannot be
accessed from a keypad that is in the armed state.
1) Enter [MENU] + [2] + [0] + [3] to disarm all areas.
2) An alternative method for disarming all areas is to enter your
PIN then press an hold the [OFF] key for 2 seconds.
Areas > Commands >
Move To Area
Each keypad on the system can operate any area, however you
can only operate the area which is currently being displayed.
The Move to Area command allows you to change the current
keypad view from one area to another.
An alternative method for changing the current area being
displayed is to enter your PIN and then press the left or right
arrow keys. Keep pressing the arrow key until the desired area is
displayed. Only areas which have been assigned to the PIN will
be available for view.
If you move to another area the keypad will automatically revert
back to its assigned home area after 2 minutes. See Menu 6-1-3,
Home Area.
Enter [MENU] + [2] + [0] + [4] and select the area from the list
1)
and press [OK] to move to the selected area.
6-2
Area Programming

- -
MENU 2-0-2
  
- -
MENU 2-0-3
  
-
MENU 2-0-4
 
A001 Security System
A002 Area 2 Name
A003 Area 3 Name
Press  OK or MENU
i
Turn off option Menu 6-1-4, Pin To change Area and use the [←]
and [→] keys to move through all areas on the system without
the need to enter your pin.
Note
Areas > Commands >
Chime On/Off
Chime mode allows you to monitor a zone (or group of zones)
by sounding the keypad buzzer or activating a programmable
output. This can be useful when you need to monitor the front
or back entrance to a premises while in the disarmed state.
To select which zones will be monitored for chime see Menu
3-0-3 — Set Chime Zones.
1) To turn chime mode On or Off enter [MENU] + [2] + [0] + [5]
and select the area from the list then press [OK].
Security System A001
Chime is OFF
To turn ON, Press ON
To Go Back Press OK
i
The Chime Tone will only be heard on keypads programmed to
sound the chime tone. See Menu 6-1-5 — Chime Tone. Software
Revision 1.02 and higher now resets any outputs that are
Note
programmed to follow chime zones when a user turns off chime
mode.
Areas > Commands >
Chime Mode
The Chime Mode option allows you to program how chime
zones will operate on an area by area basis. In latching mode a
valid PIN will need to be entered to reset the chime alarm.
It is now possible to stop the chime alarm if the door is left open
for a long period of time or to only trigger the chime alarm if the
door is left open for a period of time
Available options include;
Chime Always
Chime For 000 Seconds
Chime After 000 Seconds
Chime Latching
To set the required chime mode enter [MENU] + [2] + [0] + [6]
1)
and select the area from the list then press [OK].
A001 Security System
A002 Area 2 Name
A003 Area 3 Name
Press  OK or MENU
- - -
MENU 2-0-5
   
-
MENU 2-0-6
 
Bosch Security Systems 05/10 BLCC100I