Section 3 - Definitions; Additional Safety Symbol Definitions; Miscellaneous Symbol Definitions - Miller Trailblazer 330 Diesel Owner's Manual

3-1.

Additional Safety Symbol Definitions

�
Some symbols are found only on CE products.
3-2.

Miscellaneous Symbol Definitions

Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner's Manual.
Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner's Manual.
Amperage
Hot muffler and exhaust pipe can cause severe burns.
Voltage
Hot muffler and exhaust pipe can cause severe burns.
Rated No-Load
Voltage (OCV)
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Load Voltage
Rated Welding
Current
Do not spray water on CST units.
Do not spray water on CST units.
Duty Cycle
Negative
Door must be fully open during operation.
Door must be fully open during operation.
Positive
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation
Constant Current
and metal objects away.
and metal objects away.
Constant Voltage
�
Complete Parts List is available at www.MillerWelds.com
SECTION 3 – DEFINITIONS
Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and un
could tip avoid tipping. Be careful when moving unit over uneven surfaces.
Do not stack racks. Lift only with proper equipment and correct procedures.
Moving parts can injure.
Always connect green, Or green with yellow stripe, wire to supply grounding terminal.
Connect black, white, and red wires (L1, L2, L3) to line terminals.
Pinch points can injure.
Recycle.
Become trained and read the instructions before working on machine.
Connect green or green/yellow grounding conductor to ground terminal.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the
machine or heating.
machine or heating.
Warning! Watch Out! There are possible hazards as shown by the
symbols.
Connect green or green/yellow grounding conductor to ground
Connect green or green/yellow grounding conductor to ground
Moving parts can injure.
terminal.
terminal.
Connect input conductors (L1, L2 And L3) to line terminals.
Connect input conductors (L1, L2 And L3) to line terminals.
Never use generator inside a home or garage, even if doors and win-
Never use generator inside a home or garage, even if doors and win-
Never use generator inside a home or garage, even if doors and win-
dows are open. dows are open.
dows are open.
Only use generator outside and far away from windows, doors, and
Only use generator outside and far away from windows, doors, and
Only use generator outside and far away from windows, doors, and
vents.
vents.
vents.
Full
Empty
Engine-Driven Gen-
erator with Rectifier
Direct Current (DC)
Alternating Current
(AC)
Protective Earth Connect input conductors (L1, L2 And L3) to line terminals.
(Ground)
Circuit Breaker
Supplementary
Protector
Single Phase
Alternator
Output
Contactor On/
Electrode Hot
Safe85 2012 06
Safe85 2012 06
Safe1
Safe86 2012 06
Safe86 2012 06
Safe87 2012 07
Safe1
Safe87 2012 07
Safe1
Safe88 2012 07
Safe88 2012 07
Safe1
Do Not Switch Safe89 2017 04
Safe89 2017 04
While Welding
Remote
Safe1
Safe90 2017 04
Safe90 2017 04
Read Operator's
Manual
Safe1
Welding (General)
Safe91 2017 04
Safe91 2017 04
Shielded Metal Arc
Welding (SMAW)
Safe 1
Gas Metal Arc
Safe92 2017 04
Safe92 2017 04
Welding (GMAW)
Gas Tungsten Arc
Welding (GTAW) /
Tungsten Inert Gas
(TIG) Welding
Safe93 2012 08
Safe93 2012 08
Touch Start (GTAW)
keep hands
keep hands
Temperature
Safe95 2012 05
Safe95 2012 05
OM-291102 Page 15
Safe
Safe
Safe