Section 11 - Troubleshooting; Front Panel Display Code Information - Miller Trailblazer 330 Diesel Owner's Manual

SECTION 11 – TROUBLESHOOTING

11-1. Front Panel Display Code Information

LCD Message
Engine Oil Pressure Error -
Have Unit Serviced
Engine Overheat Error - Let
Engine Cool
Engine Temp Sensor Error -
Have Unit Serviced
Engine Battery Error - Check
Battery
Engine Overrun Error - Have
Unit Serviced
Engine Sensor Supply Error -
Have Unit Serviced
Engine Actuator Error - Have
Unit Serviced
Engine Speed Sense Error -
Have Unit Serviced
Engine Starter Error - Have
Unit Serviced
Engine Alternator Error -
Have Unit Serviced
Engine Charging Error -
Have Unit Serviced
Engine CAN Bus Error -
Have Unit Serviced
Engine Thermal Foldback -
LET ENGINE COOL
Engine Low Fuel Shutdown -
Refill Fuel
Engine Check Error - Have
Unit Serviced
Boost Connector Error -
Have Power Module
Serviced
Boost DC Bus Out of Range
- Have Unit Serviced
Boost DC Bus High Error -
Have Power Module
Serviced
Boost DC Bus Low Error -
Have Power Module
Serviced
Boost Initial Check Error -
Have Power Module
Serviced
Boost Current Sensor Error -
Have Power Module
Serviced
Boost Over Current Error -
Have Power Module
Serviced
Inverter Primary CT Error -
Have Power Module
Serviced
OM-291102 Page 68
Help Code Problem
ERR PF00 Despite RPM, oil pressure
switch is ON.
ERR PT00 Engine water temperature
greater than or equal to 239°
F (115°C).
ERR PT01 Voltage of coolant tempera-
ture sensor is out of range.
ERR PB00 ECU recognition of battery
voltage is above 18 volts.
ERR PE00 Engine speed is greater than
4140 RPM.
ERR PN00 Engine Sensor voltage low.
ERR PK00 Engine actuator current de-
tected out of range.
ERR PR00 Engine speed is 0 RPM after
Start signal into ECU.
ERR PE01 Starter running time is above
12 seconds.
ERR PE03 Alternator L terminal has volt-
age while 0 RPM (After Key
On).
ERR PB01 Alternator L terminal is 0 volts
while engine is running.
ERR PC00 CAN bus OFF.
ALRT PT03 Thermal foldback starts at
221°F (105°C) and increases
by 10% per degree until out-
put is shut off at 239°F (115°
C)
ERR PF01 Fuel level is low.
ERR PE02 Check Engine Error.
ERR EE00 Inverter Control board does
not have connector RC2
plugged in.
ERR EE01 DC bus voltage too high or
low for 10 seconds.
ERR EV00 Inverter Control board bus
voltage exceeded 480V dur-
ing operation.
ERR EU00 Inverter Control board bus
voltage went below 160V
while engine was running.
ERR EB00 Bus voltage detected below
360V after soft start.
ERR EN00 Inverter Control board current
sensor is not wired correctly
or high boost current
detected.
ERR EG00 Inverter Control board de-
tected boost current over
100A.
ERR HG00 Transformer primary current
exceeded trip level.
Always check unit before applying power. See Pre-Power Checks.
Possible Cause
Indicates malfunction of oil
pressure switch
High engine demand.
Indicates malfunction of en-
gine temp sensor.
Bad battery.
Indicates malfunction of en-
gine ECU.
Indicates malfunction of en-
gine sensor.
Indicates malfunction of en-
gine actuator.
Indicates malfunction of
speed sense signal.
Indicates malfunction of en-
gine starter.
Indicates malfunction of
alternator.
Indicates malfunction of
alternator.
Indicates malfunction of CAN
communication with engine
ECU.
High engine demand.
Fuel level is low.
Indicates malfunction of
engine.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Indicates malfunction in pri-
mary power circuit of unit.
Potential Solution
Contact a Factory Authorized
Service Agent.
Wait for unit to cool.
Contact a Factory Authorized
Service Agent.
Check battery.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Wait for unit to cool.
Refill fuel.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.
Contact a Factory Authorized
Service Agent.