Extron electronics MediaPort 300 User Manual page 64

Command Function
Output format (HDMI Loop out)
Set format
View format
USB streaming format
View streaming format
HDCP mode
Set HDCP mode
View HDCP mode
USB screen saver
Set screen saver mode
View screen saver mode
View screen saver status
Screen saver user custom logo
:
Logo files (<filename>s) should be stored in the folder nortxe-graphics. Files outside of this location require a complete path
NOTE
for the assignment.
Select logo file
View selected logo file
Power save mode
Set power save mode
View power save setting
Audio input format
View detected audio input format
X1)
KEY: = HDMI output format
:
NOTES
• If in DVI mode and a rate greater than 165 MHz is present, the output defaults to 0 (Auto).
Only available when the current resolution is 4K@50/50.94/60 Hz — use half of the TMDS character rate.
†
X1!
= USB streaming format
X1@
= HDCP mode
X1#
= Screen saver mode
X1$
= Window number
X1%
= Power save mode
X1^
= HDMI audio input type
X1&
= USB audio type
MediaPort 300 HDMI and Audio to USB Scaling Bridge • Remote Configuration and Control
SIS Command
Response
(Host to Unit)
(Unit to Host)
E X1) }
2* VTPO Vtpo2*
E } X1)]
2VTPO
E } X1!
1OTYP
Verbose mode 2 or 3:
Otyp1*
E X1@ }
S2* HDCP HdcpS2*
E } X1@]
S2HDCP
E X1# }
M1* SSAV SsavM1*
E } X1#]
M1SSAV
E }
S1SSAV SsavS1*
E }
A1,<filename>LOGO LogoA1,<filename>
E }
A1LOGO <filename>
EX1% }
PSAV Psav
E } X1%]
PSAV
Verbose mode 2 or 3:
Psav
E } X1^ X1&]
40STAT *
Verbose mode 2 or 3:
40Stat
0 = Auto (HDMI RGB full to a CEA sink, or DVI to a non-CEA sink)
1 = DVI (165 MHz max output*)
2 = HDMI RGB full
3 = HDMI RGB limited
5 = HDMI YUV limited
7 = HDMI YUV limited
9
† = HDMI YUV 420 limited (for 4K@50/59.94/60 Hz only)
0 = No active video stream
1 = MJPEG
0 = Disable Authentication
1 = Follow input (default) (10 seconds of HDCP authentication attempts)
2 = Always encrypt output (10 seconds of HDCP authentication attempts)
3 = Follow input (with continuous HDCP authentication attempts)
4 = Always encrypt output (with HDCP authentication attempts)
0 = Extron logo (default)
1 = Black screen or user logo
0 = Active input detected
0 = Full power mode (default)
1 = Low power state (TCP/IP and USB communications remain active)
9 = Automatic read-only state for unit entering over-temperature (cannot be set vis SIS)
0 = None detected
2 = LPCM-2Ch digital
0 = None detected
Additional description
X1)]
X1!]
X1@]
X1#]
X1$]
]
]
X1%]
X1%]
X1^ X1&]
*
2 = YUV2
3 = NV12
2 = Blue screen and on-screen bug
1 = No active input, screen saver active
3 = Multi-Ch digital (PCM3+ or encoded formats)
1 = LPCM-2Ch digital
56