Dalsa Linea Lite GigE Series User Manual page 84

Output Line Source
Off
Software Controlled
Pulse on: Start of Frame
Pulse on: Start of Line
Pulse on: Start of Exposure
Pulse on: Rejected Trigger
Pulse on: End of Exposure
Pulse on: Valid Line Trigger
Pulse on: Invalid Line
Trigger
Pulse on: End of Timer 1
Pulse on: End of Counter 1
Pulse on: Input 1 Signal
Pulse on: Input 2 Signal
Output Line Pulse Signal
Activation
Rising Edge
Falling Edge
Any Edge
Output Line Pulse Delay
Output Line Pulse Duration
Output Line Value
Active
Inactive
Line Status All
Output Line Software
Com mand
82 • Operational Reference
outputLineSource
SoftwareControlled
PulseOnStartofFrame
PulseOnStartofLine
PulseOnStartofExposure
PulseOnInvalidTrigger
PulseOnEndofExposure
PulseOnValidLineTrigger
PulseOnInvalidLineTrigger
PulseOnTimer1End
PulseOnCounter1End
PulseOnInput1
PulseOnInput2
outputLinePulseActivation
RisingEdge
FallingEdge
AnyEdge
outputLinePulseDelay
outputLinePulseDuration
outputLineValue
Active
Inactive
LineStatusAll
outputLineSoftwareCmd
Selects which internal signal or event driven pulse or
software control state to output on the selected line. Note,
the Line Mode feature m ust be set to Output. The List of
supported output line sources is product-specific. The
Event Control section provides details and timing diagrams
for the supported trigger m odes.
Off Line output is Open
The Output Line Value feature changes the state of the
output
Generate a pulse on the start of the Frame Active event
Generate a pulse on the start of the Line Active
Generate a pulse on the Exposure Start event. This option
is typically used to trigger a strobe light.
Generate a pulse on the Invalid Trigger event.
Generate a pulse on the Exposure End event. This option
is typically used to trigger a strobe light.
Generate a pulse on the LineTrigger event.
Generate a pulse on the Invalid LineTrigger event.
Generate a pulse on the TimerEnd 1 event.
Generate a pulse on the CounterEnd 1 event.
Generate a pulse on the Input signal 1 event
Generate a pulse on the Input signal 2 event
Specifies the input line activation mode to trigger the
Output Line pulse.
Specifies that the trigger is considered valid on the rising
edge of the source signal.
Specifies that the trigger is considered valid on the falling
edge of the source signal.
Specifies that the trigger is considered valid on the falling
or rising edge of the source signal.
Sets the delay (in µs) before the output line pulse signal.
Applicable for the Output Line Source
LineMode feature m ust be set to output.
Sets the width (duration) of the output line pulse in
m icroseconds.
Sets the output state of the selected Line if the
outputLineSoftwareLatchControl = OFF.
Source must be Software Controlled. If the
outputLineSoftwareLatchControl = Latch , the state of the
pin will change with the
command.
Sets the Output circuit to close
Sets the Output circuit to open
Returns the current status of all available line signals, at
tim e of polling, in a single bit field. The order is Line 1, 2,
3, ... (RO)
Writing a value of 1 in the bit field applies the Latch value
of the outputLineSoftwareLatchControl and/or executes
the PulseOnSoftwareCmd for any output line programmed
for software control. The feature outputLineSoftwareCmd
can take any binary value and each bit set to 1
corresponds to a Icommand for an Output.
Bit-0 is Line 3,
Bit-1 is Line 4,
Bit-2 is Line 5,
Bit-3 is Line 6
This is applicable to Output Line Source
Software Cm d (for Pulse m ode) or OutputLineSource =
Software Controlled and OutputLineSoftwareLatchControl
= Latch (for static states).
feature. Note, the
Output Line
Output Line Software Command
= Pulse On: where
Linea Lite GigE Series Camera
Beginner
DFNC
Beginner
DFNC
Beginner
DFNC
Beginner
DFNC
Beginner
DFNC
Expert
Expert
DFNC