Xerox Phaser 4600 Service Manual page 88

12-906-00, 12-907-00 Jam in Mailbox Entrance RAP
12-906-00 Media did not reach the mailbox Entrance Sensor on time. Media remains in the
IOT exit.
12-907-00 Media did not clear the Mailbox entrance sensor on time.
12-908-00 Media is blocking the Mailbox Entrance Sensor.
BSD-Reference:
WD 18
Initial Actions
• Check the Mailbox entrance sensor actuator.
• Check for obstructions blocking the media path.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: Remove the Mailbox Rear Door
the entrance sensor and actuator.
Check the condition of the Mailbox feed rollers. The feed rollers are clean and rotate freely.
Y N
Clean or repair the affected feed rollers.
code 12-905 to test the Mailbox entrance sensor. The sensor signal changes
Select dC330
(high/low).
Y N
Remove the Mailbox, GP 14 to check the condition of the Mailbox option connector,
entrance sensor and harness. The sensor is connected and the harness undamaged.
Y N
Replace the sensor or repair the harness.
Replace the Mailbox Control Board,
Select dC330 code 12-120 to test the Mailbox Transport Motor,
rotates.
Y N
Check the Transport Motor connection and harness
necessary.
Replace these components in order until the error is corrected.
1. IOT Upper Option Harness, PL 10.30 Item 24
2. MCU Board, PL 3.10 Item 3
2 Status Indicator RAPS
12-906-00, 12-907-00, 12-910-00, 12-920-00, 12-930-00,
WARNING
(REP 11.4) and base plate (PL 11.10 Item
REP 11.5.
1. The
PL 11.20 Item
(REP 11.14). Repair or reconnect as
12-910-00, 12-920-00, 12-930-00, 12-940-00 Mailbox Bin Full
12-910-00 Mailbox Bin 1 is full.
12-920-00 Mailbox Bin 2 is full.
12-930-00 Mailbox Bin 3 is full.
12-940-00 Mailbox Bin 4 is full.
BSD-Reference:
WD 18
Initial Actions
• Check the stack full actuator of the affected output tray.
• Reseat the Mailbox on the IOT.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
7) to access
NOTE: Bins (output trays) are numbered 1 through 4, 4 being the top tray.
Check the condition of the stack full actuator. The actuator moves freely and is undam-
aged.
Y N
Clean or repair the affected actuator.
Select dC330 code 12-910 (1), 12-920 (2), 12-930 (3), or 12-940 (4) to test the stack sensor of
the affected output tray. The sensor signal changes (high/low).
Y N
Remove the Mailbox,
harness. The connector and harness are undamaged.
Y N
Repair the harness.
Remove the Mailbox right cover and reseat P/J5 on the Mailbox Control Board. The
motor error message is displayed.
Y N
Reassembly and perform
Replace the Mailbox Control Board,
Replace these components in order until the error is corrected.
1. IOT Upper Option Harness,
2. MCU Board, PL 3.10 Item 3
04/2016
2-64
WARNING
GP 14 to check the condition of the Mailbox option connector and
SCP 6 Final Actions.
REP 11.5.
PL 10.30 Item 24
Phaser 4600/4620/4622 Printer Service Manual
Revised