Xerox Phaser 4600 Service Manual page 363

Table 8 Input Codes 12
Code Display Name Description
12-860 Low Staple Sensor Low Staple Sensor
12-870 Staple Door Switch Staple Door Interlock
12-890 Diverter Home Sensor Exit Gate Sensor
12-895 Jam Cover Sensor Rear Door Sensor
12-900 Diverter Home Sensor Exit Gate Sensor
12-905 Entrance Sensor Mailbox Entrance Sensor
12-910 Bin1 Full Mailbox Tray 1 Stack Full
12-911 Bin1 Empty Mailbox Tray 1 No Paper
12-915 Rear Door Mailbox Rear Door Interlock
12-920 Bin2 Full Mailbox Tray 2 Stack Full
12-921 Bin2 Empty Mailbox Tray 2 No Paper
12-925 Upper Diverter Home Upper Diverter Home Position High/Low
12-930 Bin3 Full Mailbox Tray 3 Stack Full
12-931 Bin3 Empty Mailbox Tray 3 No Paper
12-940 Bin4 Full Mailbox Tray 4 Stack Full
12-941 Bin4 Empty Mailbox Tray 4 No Paper
12-945 Lower Diverter Home Lower Diverter Home Position High/Low
Output Components
When the appropriate code is entered, the component is activated and its status appears on
the Control Panel.
Go to the appropriate table:
• Table 9 Output Codes 04 IOT Motors
• Table 10 Output Codes 06 Laser Unit
• Table 11 Output Codes 08 Feeder motors and clutches
• Table 12 Output Codes 09 Xerographics
• Table 13 Output Codes 10 Fuser drive
• Table 14 Output Codes 12 Finisher/Mailbox drive
Table 9 Output Codes 04
Code Display Name Description
04-100 Main BLDC Motor Run the Main Drive motor
04-120 Main Fan Run the SMPS Fan
04-181 K Dev motor Run the developer motor
04-191 K Dev motor ready Run the developer motor
04-200 Exit Motor Forward Fast Run the Exit Drive Assembly
04-220 Exit Motor Reverse Reverse the Exit Drive
04-230 Duplex Motor Forward Run the Duplex Drive
04-580 Feed BLDC Motor Run the Feed Drive Assembly On/Off
04-590 Feed BLDC Motor Ready Feed Drive Assembly
Lift Motor Check
Revised
Phaser 4600/4620/4622 Printer Service Manual
General Code
High/Low 06-100 LSU Motor Run
High/Low 06-200 LSU LD power
High/Low 06-300 LSU Fan Run
High/Low
06-310 Checking LSU Hsync
High/Low
High/Low
Code
High/Low
High/Low
08-810 T1 Pick-up Clutch
High/Low
08-820 T2 Pick-up Clutch
High/Low
08-830 T3 Pick-up Clutch
High/Low
08-840 T4 Pick-up Clutch
08-850 Registration Clutch
High/Low
08-855 T5 Pick-up Clutch
High/Low
08-856 T6 Pick-up Clutch
High/Low
08-820 T2 Feed Motor Run
High/Low
08-930 T3 Feed Motor Run
08-940 T4 Feed Motor Run
08-950 T5 Feed Motor Run
08-960 T6 Feed Motor Run
Code
09-100 MHV Bias
09-200 Dev Bias
09-300 THV Bias
09-400 THV Bias
09-500 SMPS Fan Run
General
09-600 Toner dispense motor
On/Off
09-950 Erase lamp
On/Off
On/Off
High/Low
Code
On/Off
On/Off 10-100 Fuser Power On Main
On/Off
10-110
On/Off
04/2016
6-31
Table 10 Output Codes 06
Display Name Description
Laser Unit scan motor
Laser diode half power
Right Chassis Fan
Table 11 Output Codes 08
Display Name Description
Tray 1 Feed Clutch
Tray 2 Feed Clutch
Tray 3 Feed Clutch
Tray 4 Feed Clutch
Registration Clutch
Tray 5 Feed Clutch
Tray 6 Feed Clutch
Tray 2 Feed Drive Motor
Tray 3 Feed Drive Motor
Tray 4 Feed Drive Motor
Tray 5 Feed Drive Motor
Tray 6 Feed Drive Motor
Table 12 Output Codes 09
Display Name Description
MHV bias voltage on at nor-
mal drive level.
Developer bias voltage on at
normal drive level.
THV plus bias voltage on at
normal drive level.
THV negative bias voltage on
at normal drive level.
Run SMPS Fan
Run the toner dispense motor
in the Main Drive Assembly
Toggle the Erase lamp
Table 13 Output Codes 10
Display Name Description
Raises Fuser temperature to
180 degree setpoint.
Fuser Power On Side Raises Fuser temperature to
180 degree setpoint.
General
On/Off
On/Off
On/Off
General
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
General
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
General
On/Off
On/Off
6 General Procedures and Information
dC330