Danfoss VLT AQUA Drive FC 200 Instruction Manual page 106

VLT AQUA Low Harmonic Drive Instruction
Manual
0-23 Display Line 2 Large
Option:
[1615] * Frequency
0-24 Display Line 3 Large
Option:
[1652] * Feedback [Unit]
0-37 Display Text 1
Range:
0* [0 - 0 ]
0-38 Display Text 2
Range:
0* [0 - 0 ]
0-39 Display Text 3
Range:
0* [0 - 0 ]
0-70 Set Date and Time
Range:
2000-01-01 [2000-01-01 00:00]
00:00 –
2099-12-01
23:59 *
Function:
Select a variable for display in line 2.
The options are the same as those listed for par. 0-20
Function:
The options are the same as those listed for par. 0-20
Select a variable for display in line 2.
Function:
In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If it is to be displayed permanently, select Display Text 1 in
Display Line 1.1 Small
par. 0-20
Small , par. 0-23 Display Line 2 Large
the LCP to change a character. Use the
highlighted by the cursor, it can be changed. Use the
character. A character can be inserted by placing the cursor between two characters and pressing
▲ ▼
or .
Function:
In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If to be displayed permanently select Display Text 2 in par. 0-20
Line 1.1 Small Display Line 1.2 Small
, par. 0-21
Line 2 Large or par. 0-24 Display Line 3 Large
◀ ▶
character. Use the and buttons to move the cursor. When a character is highlighted by the
cursor, this character can be changed. A character can be inserted by placing the cursor between
▲
two characters and pressing or
Function:
In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If it is to be displayed permanently, select Display Text 3 in
Display Line 1.1 Small
par. 0-20 ,par. 0-21
par. 0-23 Display Line 2 Large or par. 0-24
LCP to change a character. Use the
highlighted by the cursor, this character can be changed. A character can be inserted by placing the
cursor between two characters and pressing
Function:
Sets the date and time of the internal clock. The format to be used is set in par. 0-71 and 0-72.
NOTE!
This parameter does not display the actual time. This can be read in par. 0-89.
The clock will not begin counting until a setting different from default has been
made.
®
MG.20.T1.22 - VLT is a registered Danfoss trademark
6 How to Program the Low Harmonic Drive
Display Line 1.1 Small
Display Line 1.1 Small
Display Line 1.2 Small
, par. 0-21 , par. 0-22
or par. 0-24 Display Line 3 Large . Use the
◀ ▶
and buttons to move the cursor. When a character is
▲ ▼
or buttons on the LCP to change a
Display Line 1.3 Small
, par. 0-22
▲ ▼
. Use the or buttons on the LCP to change a
▼
.
Display Line 1.2 Small
, par. 0-22
Display Line 3 Large . Use the
◀ ▶
and buttons to move the cursor. When a character is
▲ ▼
or .
.
Display Line 1.3
▲ ▼
or buttons on
6
Display
Display
, par. 0-23
Display Line 1.3 Small
,
▲ ▼
or buttons on the
6-13