System Wiring Examples Electrolynx Qc12 Hinge - Assa Abloy Corbin Russwin PED5000 D Series Installation Instructions Manual

Premium Delayed Egress
PED4000 D, PED5000 D Series Exit Device
Installation Instructions
12

System Wiring Examples ElectroLynx QC12 Hinge

10 System Wiring Examples (continued)
10 System Wiring Examples (continued)
DEED system with Fail Safe Electrified Exit Trim (ET) and ElectroLynx QC12 Hinge
Delayed Egress System with Fail Safe Electrofied Exit Trim (ET) and ElectroLynx QC12 Hinge.
DEED system with Fail Safe Electrified Exit Trim (ET) and ElectroLynx QC12 Hinge
During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and Fail Safe ET, and allows immediate
egress and ingress.
During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and Fail Safe ET, and allows immediate
For External Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
egress and ingress.
allows egress for a time period programmable at the keypad. A valid code entry at the Outside keypad or valid card presentation at
For External Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
Outside card reader removes power from the Fail Safe ET and allows ingress for a time period programmable at the keypad.
allows egress for a time period programmable at the keypad. A valid code entry at the Outside keypad or valid card presentation at
Outside card reader removes power from the Fail Safe ET and allows ingress for a time period programmable at the keypad.
120VAC (L,N,G)
120VAC (L,N,G)
To closed Fire
Alarm Contact
To closed Fire
Alarm Contact
When fire alarm is
activated, contact opens,
When fire alarm is
disconnects 24VDC to
activated, contact opens,
DEED, allowing
disconnects 24VDC to
immediate egress
DEED, allowing
immediate egress
Closeup of end bracket
(with metal tab for P5 Installation)
Connect P5 to this metal
tab on end bracket
QC12 Hinge
QC12 Hinge Pigtail
or
QC12 Hinge Pigtail
15' Frame Harness
or
15' Frame Harness
For installation assistance contact Corbin Russwin
1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part without
the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
(-)
Securitron
(-) +24VDC
BPS
Securitron
+24VDC
24VDC
BPS
1AMP
24VDC
Power Supply
1AMP
Connect Green wire to Earth
Power Supply
Ground (EGND) within BPS Power
Connect Green wire to Earth
Supply or Local Building Ground
Note: Power Supply Ground (EGND) within BPS Power
Supply or Local Building Ground
24VDC, 2A minimum
Note: Power Supply
per DEED
24VDC, 2A minimum
per DEED
1 2 3
4 5 6
NO
1 2 3
7 8 9
4 5 6
NO
4291 * 0 #
7 8 9
(Inside)
4291
* 0 #
Keypad
(Inside)
C
Or
Keypad
Inside Card
C
Or
Reader Relay
Inside Card
(by others)
Reader Relay
(by others)
QC12 Hinge
Premium Delayed Egress
Exit Device (DEED)
Premium Delayed Egress
Exit Device (DEED)
Door Harness
3" Typical
Door Harness
3" Typical
ElectroLynx pluggable
8-pin and 4-pin
ElectroLynx pluggable
connectors
8-pin and 4-pin
connectors
8, Yellow (RAR NC)
8, Yellow (RAR NC)
Note: Wiring to remaining wires is as required
Note: Wiring to remaining wires is as required
(-)
(+)
C
(-)
(+)
C 4, Tan (SEC NO)
4, Tan (SEC NO)
1 2 3
4 5 6
1 2 3
7 8 9
4 5 6
* 0 #
4292
7 8 9
(Outside)
* 0 #
4292
Keypad
(Outside)
Or
Keypad
Outside Card
Or
Reader Relay
(-)
Outside Card
(by others)
Reader Relay
(-)
(by others)
(ET+) Red, 2
(ET-) Black, 1
(ET+) Red, 2
5-pin
(ET-) Black, 1
connector
5-pin
connector
Premium 775 (or 773) Fail Safe
Electrified Exit Trim (ET)
Premium 775 (or 773) Fail Safe
Electrified Exit Trim (ET)
From outside of door, route ET wire through
chassis into the opposite side of the LBM wiring,
From outside of door, route ET wire through
then plug ET 5-pin connector into mating rail
chassis into the opposite side of the LBM wiring,
harness 5-pin connector. Ensure wires are tucked
then plug ET 5-pin connector into mating rail
in, to avoid pinching wires by push bar or chassis
harness 5-pin connector. Ensure wires are tucked
mechanism.
in, to avoid pinching wires by push bar or chassis
mechanism.
Note: Fail Secure ET
requires different wiring, as
Note: Fail Secure ET
shown on next page
requires different wiring, as
shown on next page
30
Connect
to QC12
Connect
to QC12
Hinge
QC12 Hinge Pigtail
or
QC12 Hinge Pigtail
15' Frame Harness
or
15' Frame Harness
Wiring Notes:
1. Rail harness, door harness, electric hinge
Wiring Notes:
and pigtail/frame harness connector
1. Rail harness, door harness, electric hinge
terminations and wire colors all match.
and pigtail/frame harness connector
2. Wiring to remaining hinge pigtail wires is as
terminations and wire colors all match.
required. Tape or cap off ends of unused pigtail
2. Wiring to remaining hinge pigtail wires is as
wires (not shown) to ensure that they don 't short
required. Tape or cap off ends of unused pigtail
to anything.
wires (not shown) to ensure that they don 't short
3. A fire alarm tie-in is required on fire rated
to anything.
openings.
3. A fire alarm tie-in is required on fire rated
4. Rail DPS bypass dip switch 8 must be set
openings.
ON, which is default setting.
4. Rail DPS bypass dip switch 8 must be set
5. As another option, instead of wiring to the
ON, which is default setting.
External Inhibit (EI) input Orange wire pin 5,
5. As another option, instead of wiring to the
you could move wire to the Remote Reset (RR)
External Inhibit (EI) input Orange wire pin 5,
input, White wire pin 3.
you could move wire to the Remote Reset (RR)
input, White wire pin 3.
Note that when using RR it will add 5, 10,
20, or 40sec (depending DEED reset delay
Note that when using RR it will add 5, 10,
dip switch setting) to the keypads/card
20, or 40sec (depending DEED reset delay
RR also can be
readers time setting.
dip switch setting) to the keypads/card
used to rearm DEED from alarm
RR also can be
readers time setting.
condition.
used to rearm DEED from alarm
condition.
Hinge
FM574 01/23