Table of Contents
Advertisement
Quick Links
Installation Instructions
PE8800 & 12-PE8800 Series
Rim Exit Device for 16, 28, 63, & 66 Functions
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
A8296A 2/23
Advertisement
Table of Contents
Related Manuals for Assa Abloy SARGENT PE8800 Series
Summary of Contents for Assa Abloy SARGENT PE8800 Series
- Page 1 Installation Instructions PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions WARNING WARNING This product can expose you to Attention Installer: Improper lead which is known to the state of installation may result in damage California to cause cancer and birth to the product and void the factory defects or other reproductive harm.
-
Page 2: Screw Chart
PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Screw Chart TOTAL QTY SCREW WHERE USED SUPPLIED (4) CHASSIS CORNER MOUNTING HOLES (METAL DOOR) #10-24 X 3/4" FLAT HEAD MACHINE SCREW (4) CHASSIS CORNER MOUNTING HOLES (WOOD DOOR) #10 X 1-1/4"... -
Page 3: Tools Needed
PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Tools Needed Support Block (Provided) Rail Cutting Guide (Provided) Before installation: 1. Install mullion, if used. 2. Fit and hang door. 3. Check the box’s label for the size of the exit device. 4. -
Page 4: Exploded View
PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Exploded View Mounting Plate End Cap Rail Assembly Rim Cylinder “Lock Down Key” To operate: Depress pushrail; insert hex key, and turn counter clockwise. Attention: Not available with 12- (Fire Rated) Exit Collar... - Page 5 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Single Door (12 - Fire Rated Exit Device) Prepare Door Door 2-1/4” Vertical reference 649 Strike line (℄ of chassis) Single Door (Non-Fire Rated) Door “A”...
- Page 6 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Extend rail horizontal centerline Align chassis template with reference lines. Tape to door surface. Mark all holes and openings. Drill and tap (4) #10-24 chassis mounting holes, Align trim template to outside of door.
-
Page 7: Install Strike
PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install Strike Drill thru-holes for trim mounting screws. Cut out Extend rail horizontal centerline to frame. openings for lever spindle and cylinder, if used (this side only) Align strike on centerline, flush against door face, Drill and tap (2) #10-24 tapped holes. - Page 8 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install Chassis Attach chassis with (4) #10-24 flat head machine Attach strike with (2) #10-24 oval head screws. DO NOT FULLY TIGHTEN. chine screws and lock washers. A8296A 2/23 1-800-727-5477 •...
- Page 9 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Rail cutting guide If the rail doesn’t need to be cut, continue to page 10, step 12. If the rail must be cut, follow these steps on page 8 and 9: Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.
- Page 10 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Rail cutting guide, continued. Cut line C. Ensure plastic insert support is installed under the D. Wrap the rail and insert in masking tape, as cut line.
- Page 11 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install Rail Assembly Depress chassis lift arm. Slide rail assembly Ensure rail carrier tabs are aligned onto chassis. with chassis. Tighten chassis mounting screws. Insert the end cap bracket into the rail assembly.
- Page 12 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Ensure mounting rail bracket is against Level the rail and mark mounting holes, the rail without a gap. using the bracket as a guide. Attach mounting bracket with (2) #10-24 round Drill and tap end cap bracket holes #10-24 head machine screws.
- Page 13 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Loosen outer screws. Adjust strike for proper Mark inner mounting screw hole locations. position. Re-tighten screws. Check exit device for proper oper ation. Lock down strike with (2) #10-24 round head Drill and tap (2) #10-24 holes.
- Page 14 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install P700 Exit Trim 16 Function Insert trim. Ensure lever spindle aligns with Secure trim with (2) 1/4 - 20 flat head machine bell housing hub and rim cylinder tailpiece screws through chassis.
- Page 15 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install 800 Series Thumbpiece Trim Rim Cylinder 16, 28, 63 & 66 Functions Mount rim cylinder with (2) screws through chassis. 28, 63 & 66 Function 25 Install Chassis Cylinder (PE8816 &...
- Page 16 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Insert mortise cylinder through blocking ring into cylinder support. Tighten set screw with 5/64” wrench. A8296A 2/23 1-800-727-5477 • www.sargentlock.com Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
-
Page 17: Install Covers
PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions Install Covers Attach chassis cover and end cap using (6) #8-32 Check for proper operation. machine screws. A8296A 2/23 1-800-727-5477 • www.sargentlock.com Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. - Page 18 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions A8296A 2/23 1-800-727-5477 • www.sargentlock.com Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
- Page 19 PE8800 & 12-PE8800 Series Rim Exit Device for 16, 28, 63, & 66 Functions Installation Instructions A8296A 2/23 1-800-727-5477 • www.sargentlock.com Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
- Page 20 1-800-727-5477 • www.sargentlock.com Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents. A8296A 2/23...