Table of Contents
Advertisement
•
•
The operator must be familiar with the contents of the OPERATION section
The operator must be familiar with the contents of the OPERATION section
before starting the roller.
before starting the roller.
•
•
Ensure that all instructions in the MAINTENANCE section are followed.
Ensure that all instructions in the MAINTENANCE section are followed.
•
•
Only the operator is allowed to be on the roller. Remain seated at all times
Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller.
when operating the roller.
•
•
Never use the roller if it is in need of adjustment or repair.
Never use the roller if it is in need of adjustment or repair.
•
•
Only ascend and descend the roller when it is stationary. Use the intended
Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
machine. Never jump down from the machine.
•
•
Dynapac always recommends mounted ROPS (Roll Over Protective
Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage.
Structure), or a ROPS-approved cab and seat belt usage.
•
•
Drive slowly in sharp bends.
Drive slowly in sharp bends.
•
•
Avoid driving across slopes. Drive straight up or straight down the slope.
Avoid driving across slopes. Drive straight up or straight down the slope.
•
•
Never operate with the drum outside the edge, the substrate might not have
Never operate with the drum outside the edge, the substrate might not have
full bearing strength or the edge is close to a slope. Avoid operating close to
full bearing strength or the edge is close to a slope. Avoid operating close to
edges and ditches and the like as well as on poor ground conditions that
edges and ditches and the like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to support the roller.
jeopardizes the bearing strength and capacity to support the roller.
•
•
Make sure that there are no obstacles in the direction of travel, on the
Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
ground, in front of or behind the roller, or overhead.
•
•
Drive particularly carefully on uneven ground.
Drive particularly carefully on uneven ground.
•
•
Keep the roller clean. Clean any dirt or grease that accumulates on the
Keep the roller clean. Clean any dirt or grease that accumulates on the
footsteps or operator platform to avoid slipping risk. Keep all signs and
footsteps or operator platform to avoid slipping risk. Keep all signs and
decals clean and legible.
decals clean and legible.
•
•
Safety measures before refueling:
Safety measures before refueling:
- Stop the engine
- Stop the engine
- Do not smoke.
- Do not smoke.
- No naked flames in the vicinity of the roller.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle by keeping it in contact to the tank
- Earth the filling equipment nozzle by keeping it in contact to the tank
opening to avoid sparks.
opening to avoid sparks.
•
•
Before repairs or service:
Before repairs or service:
- Chock the drums/wheels.
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade, edge
- Place blocks under overhanging equipment, such as strike-off blade, edge
cutter/compactor and chip spreader.
cutter/compactor and chip spreader.
2023-01-25
Safety - General instructions
Safety - General instructions
(Also read the safety manual)
4812159901_D.pdf
7
Advertisement
Table of Contents
