Siemens SIPROCESS GA700 Operating Manual page 7

6.14.1.1 [2.20.02] Heaters OXYMAT 7 ............................................................................................... 190
6.14.1.2 [2.20.02] Heaters ULTRAMAT 7 ........................................................................................... 190
6.14.1.3 [2.20.02] Heaters CALOMAT 7 ............................................................................................. 190
6.14.2 [2.20.03] Factory calibrations ................................................................................................ 190
6.14.2.1 Overview ............................................................................................................................... 190
6.14.2.2 Note on setting ...................................................................................................................... 191
6.14.2.3 [2.20.03] Factory calibrations OXYMAT 7 ............................................................................ 191
6.14.2.4 [2.20.03] Factory calibrations ULTRAMAT 7 ........................................................................ 193
6.14.2.5 [2.20.03] Factory calibrations CALOMAT 7 .......................................................................... 195
6.14.3 [2.20.04] Calibrate pressure sensor ...................................................................................... 196
6.14.3.1 Overview ............................................................................................................................... 196
6.14.3.2 [2.20.04] Calibrate pressure sensor OXYMAT 7 .................................................................. 197
6.14.3.3 [2.20.04] Calibrate pressure sensor ULTRAMAT 7 .............................................................. 198
6.14.3.4 [2.20.04] Calibrate pressure sensor CALOMAT 7 ................................................................ 198
6.14.4 [2.20.06] Reference gas pump OXYMAT 7 .......................................................................... 199
6.14.5 [2.20.10] Name/unit ............................................................................................................... 200
6.14.6 [2.20.11] Physical measuring range ..................................................................................... 201
6.14.7 [2.20.12] Switch message system off/on .............................................................................. 202
6.15 [3.01] Maintenance & Diagnostics > Current messages ...................................................... 203
6.15.1 Displaying current messages ................................................................................................ 203
6.15.2 Filtering current messages ................................................................................................... 204
6.15.3 Reading current messages ................................................................................................... 205
6.16 [3.02] Maintenance & Diagnostics > Messages to be acknowledged .................................. 206
6.16.1 Displaying messages to be acknowledged ........................................................................... 206
6.16.2 Acknowledge message ......................................................................................................... 207
6.16.3 Acknowledge all messages .................................................................................................. 208
6.17 [3.03] Maintenance & Diagnostics > Logbook ...................................................................... 209
6.17.1 Overview of logbook ............................................................................................................. 209
6.17.2 [3.03.1] Display logbook ....................................................................................................... 212
6.17.3 [3.03.1] Filter logbook entries ............................................................................................... 213
6.17.4 [3.03.2] Delete logbook ......................................................................................................... 214
6.18 [3.04] Maintenance & Diagnostics > Measured value status ................................................ 214
6.19 [3.05] Maintenance & Diagnostics > Diagnostics values ...................................................... 215
6.19.1 [3.05.1] Measured signal diagnostics ................................................................................... 215
6.19.1.1 Measured signal .................................................................................................................... 215
6.19.1.2 Heating controller .................................................................................................................. 217
6.19.2 [3.05.2] Predictive self-diagnostics ULTRAMAT 7 ................................................................ 218
6.19.3 [3.05.3] Electric parameters .................................................................................................. 219
6.19.4 [3.05.4] Inputs/outputs .......................................................................................................... 221
6.19.4.1 [1] Analog inputs ................................................................................................................... 221
6.19.4.2 [2] Analog outputs ................................................................................................................. 221
6.19.4.3 [3] Digital inputs .................................................................................................................... 222
6.19.4.4 [4] Digital outputs .................................................................................................................. 222
6.19.5 [3.05.5] Communications ...................................................................................................... 223
6.19.5.1 MODBUS TCP node ............................................................................................................. 223
6.19.5.2 MODBUS TCP digital inputs ................................................................................................. 224
6.19.6 [3.05.6] Operating hours counter .......................................................................................... 224
6.20 [3.06] Maintenance & Diagnostics > Drift values .................................................................. 225
6.20.1 Editing zero point drift values ................................................................................................ 225
Operating with the Local User Interface
Operating Manual, 06/2017, A5E31930478-05
Table of contents
7