Table of Contents
Advertisement
Revision
Date
A/B
05/01/2009
C
9/25/2009
D
10/15/10
E
2/28/11
F
11/27/11
G
12/12/12
H
3/14/13
I
4/25/13
J
10/28/2013
K
11/7/2014
L
11/17/15
M
3/09/16
N
2/10/17
O
5/22/17
P
9/22/17
Q
1/15/18
R
8/15/18
ML0021
Changes
Update Bitronics Name, Logo, cover page
Updates per New Firmware release: Updated frequency accuracy
specification in 1.3 &, 7.3; Updated standards in 1.4.2; Updated P40
Transducer input module poll rate specification in 10.3, 10.8.3, &
Figure 21. Increased waveform recorder limit in 5.4.1 from 999 to
2000 cycles (or from 16.7 to 33.3 seconds at 60Hz). Added several
paragraphs to address processing limits associated with generating
long length waveform recorder COMTRADE files and
recommendations to alleviate loss of data in long WR files.
Removed paragraph entitled "5.4.2c Using the Disturbance
Recorder for Fault Distance" and in 4.13 removed the reference to
5.4.2c.
Moved Network Time Synchronization from Section 5.8 to 5.8.5.
Moved SNTP from section 5.8.1 to 5.8.6. Rewrote section 5.8
through 5.8.7 to summarize Time sync methods. Added the ability
for a DNP slave to solicit a request for time sync from the DNP
master in order to periodically set the DNP time. Added SNTP Time
Sync, DNP Time Sync and Best Clock to 4.14 List of Available
Measurements.
Updates per new firmware release: Modifications to add section
5.13.6 for SMS control characters, modifications in fault analysis
section 6.14 including adding Peak Fault Measurement, updated
Measurement table in 6.15
Updates per new firmware release: inserted new section 5.4.5
covering IEEE long file naming convention, 5.3.8 Periodic Triggering
and updated signal input and accuracy and revenue accuracy
sections for dual peak range current options.
Updates per new firmware release: Note regarding reallocation of
memory for recording and change to length of pre- and post-trigger
time in DR in section 5.4
Added/corrected burden information on signal input modules S11,
S14, and S17 on pages 2 - 4 and in section 7.3. Updated standards
in section 1.4.2 Environment. Added information for new H12 host
module and H12E1 and H12E3 Host/Ethernet options in sections 2,
3, and 8. Modified input range spec for digital I/O in low input range.
Updated for change to lithium battery to capacitor backup.
Updated firmware version table in support of IEC 61850 deadband
release
Revised Section 1.4.3. UL/IEC 61010-1 ed. 2 is replaced by UL/IEC
61010-1 (ed.3) and IEC 6101-2-030 (ed.1).
Updated Signal input requirements based on UL project evaluation
to standards IEC61010-1 (ed.3) & IEC61010-2-030 (ed.1).
Overcurrent protection specified for VTs. Current measurement
inputs are intended for connections to isolated grounded secondary
CT circuits to comply to UL/IEC 61010-1. Revised associated sub-
sections 1.3, 7.3, 7.4, 7.5, 7.6, and added 7.5.1. New DoC.
Added current input information for S1C split-core option
Added support for P33 eight output module
Maintenance Upgrade, new firmware version
Updated manual for new DoC, changes to 1.4.2, revised 9.3 for
isolation specification on I/O channel to channel from 2000 Vac to
1500 Vdc. Added section 5.4.8 for SER recording.
Updated firmware version, corrected error in section 1.4.2
Added current input information for S2C split-core option
Updated manual for new DoC. Changes made in 1.4.2 as follows:
Added RoHS compliance; Indicated restrictions regarding CE mark
for modules S1C, S2C, P33, P10, P11, P12, and H11.
Added RS-232/RS-485 connections for D650 Display
August 15, 2018
164
Copyright 2018 Bitronics, LLC
By
E. DeMicco
R. Fisher
E. DeMicco
E. DeMicco
E. DeMicco
E. DeMicco
E. DeMicco
E. DeMicco
R.Fisher,
E. DeMicco
E. DeMicco
E. DeMicco
E. DeMicco
E.DeMicco,
R.Fisher
E. DeMicco
E. DeMicco
E. DeMicco
E. DeMicco
Advertisement
Table of Contents
Troubleshooting
