Ametek 5100 HD User Manual page 117

139 rw uint16 ANAOUT1OR
140
rw uint16 ANAOUT1F
141 r float ANAOUT2
142
rw float ANAOUT2O
143 rw uint16 ANAOUT2P
144
rw float ANAOUT2S
145
rw int16 ANAOUT2T
146 rw uint16 ANAOUT2OR
147
rw uint16 ANAOUT2F
148 r uint16 RELAY1
149
rw uint16 RELAY1D
150 rw uint16 RELAY1F
151 rw uint16 RELAY1S
152 rw float RELAY1V
153
r uint16 RELAY2
154 rw uint16 RELAY2D
155
rw uint16 RELAY2F
156 rw uint16 RELAY2S
157
rw float RELAY2V
158 r uint16 RELAY3
159 rw uint16 RELAY3D
160 rw uint16 RELAY3F
161 rw uint16 RELAY3S
162
rw float RELAY3V
163 r uint16 RELAY4
164
rw uint16 RELAY4D
165 rw uint16 RELAY4F
166
rw uint16 RELAY4S
167 rw float RELAY4V
0 = 3.78 - 20.5, 1 = 0-20.5, high or low
values can also be set by fault value, See
Fault option (ANAOUT1F)
133 1 Current Output 1 Over range Enable.
0=disabled, 1=enabled
134 1 Current Output 1 Fault Option. 0=No fault,
1=Low fault, 2=High fault.
If high fault (2):
High end of range becomes 22 mA
Output ratio becomes 1
If low fault (1) AND in 4-20 mode
(ANAOUT1T = 0):
Low end of range becomes 3 mA
Output ratio becomes 0.
135 2 Current Output 2 -
137 2 Current Output 2 Offset -
139 1 Current Output 2 Parameter-
140 2 Current Output 2 Span -
142 1 Current Output 2 Output Type. 0=4-20 mode,
1=0-20 mode.
If overange enable (ANAOUT2OR = 1)
0 = 3.78 - 20.5, 1 = 0-20.5, high or low
values can also be set by fault value, See
Fault option (ANAOUT2F) -
143 1 Current Output 2 Over range Enable.
0=disabled, 1=enabled
144 1 Current Output 2 Fault Option. 0=No fault,
1=Low fault, 2=High fault.
If high fault (2):
High end of range becomes 22 mA
Output ratio becomes 1
If low fault (1) AND in 4-20 mode
(ANAOUT2T = 0):
Low end of range becomes 3 mA
Output ratio becomes 0.
145 1 Relay 1. 0=OPEN, 1=CLOSED
146 1 Relay 1 Delay. Holds the relay output for this
set amount of time.
147 1 Relay 1 Function. 0=Disabled,
1=Concentration, 3=Data Valid, 4=System
alarm
148 1 Relay 1 Source. The source parameter
number used to evaluated the relay function.
149 2 Relay 1 Value. The value used to evaluate
the relay function.
151 1 Relay 2. 0=OPEN, 1=CLOSED
152 1 Relay 2 Delay. Holds the relay output for this
set amount of time.
153 1 Relay 2 Function. 0=Disabled,
1=Concentration, 3=Data Valid, 4=System
41
alarm
154 1 Relay 2 Source. The source parameter
number used to evaluated the relay function.
155 2 Relay 2 Value. The value used to evaluate
the relay function.
157 1 Relay 3. 0=OPEN, 1=CLOSED
158 1 Relay 3 Delay. Holds the relay output for this
set amount of time.
159 1 Relay 3 Function. 0=Disabled,
1=Concentration, 3=Data Valid, 4=System
alarm
160 1 Relay 3 Source. The source parameter
number used to evaluated the relay function.
161 2 Relay 3 Value. The value used to evaluate
the relay function.
163 1 Relay 4. 0=OPEN, 1=CLOSED
164 1 Relay 4 Delay. Holds the relay output for this
set amount of time.
165 1 Relay 4 Function. 0=Disabled,
1=Concentration, 3=Data Valid, 4=System
alarm
166 1 Relay 4 Source. The source parameter
number used to evaluated the relay function.
167 2 Relay 4 Value. The value used to evaluate
the relay function.
|
Maintenance 6-17