Ametek 5100 HD User Manual page 106

121 rw
122
r
123 r
124 rwf
125 r
126 r
127 r
128 r
129
r
130 r
131
r
132 r
133
r
134 r
135
rw
136 rw
137 rw
138
rw
139 rw
140
rw
141
r
142 rw
143
rw
144 rw
145
rw
146 rw
147 rw
148 r
149 rw
150 rw
6-6 | Model 5100 HD Analyzer
151 rw
char[10] TEMPUNIT
uint DATAVALID
int16 DMODE
int16 COMPPT
uint SYSALARM1
uint SYSALARM2
uint USERALARM
uint CONCALARM
int16 SYSSTATUS
int16 SYSSTATE
uint TOTUPTIME
uint UPTIME
float CELLTEMPD
float ANAOUT1
float ANAOUT1O
uint16 ANAOUT1P
float ANAOUT1S
int16 ANAOUT1T
uint16 ANAOUT1OR
uint16 ANAOUT1F
float ANAOUT2
float ANAOUT2O
uint16 ANAOUT2P
float ANAOUT2S
int16 ANAOUT2T
uint16 ANAOUT2OR
uint16 ANAOUT2F
uint16 RELAY1
uint16 RELAY1D
uint16 RELAY1F
uint16 RELAY1S
oz/in2, torr, atm
100 5 Temp Unit of Measure, case
sensistive. Valid strings include
degreeC, degreeF, degreeK
105 2 Data Valid. 0=Not Valid, 1=Valid
107 1 0=Line-lock mode, 1=Sample,
2=Calib
108 1 Pressure and temp compensation.
0=none, 1=pressure, 2=temperature,
3=both
109 2 Bit-mapped system alarms
111 2 Bit-mapped system alarms
113 2 Bit-mapped system alarms
115 2 Bit mapped concentration alarms
117 1 System Status. 0=Everything ok, Not
0=something is wrong
118 1 System State. 100=Not Ready,
201=Measure Run, 502=Idle,
600=diag
119 2 Total uptime in seconds
121 2 Uptime in seconds
123 2 Cell temp for display
125 2 Current Output 1
127 2 Current Output 1 Offset
129 1 Current Output 1 Parameter
130 2 Current Output 1 Span
132 1 Current Output 1 Output Type. 0=4-
20 mode, 1=0-20 mode.
If overange enable (ANAOUT1OR =
1)
low values can also be set by fault
value, See Fault option (ANAOUT1F)
133 1 Current Output 1 Over range Enable.
0=disabled, 1=enabled
134 1 Current Output 1 Fault Option. 0=No
fault, 1=Low fault, 2=High fault.
If high fault (2):
If low fault (1) AND in 4-20 mode
(ANAOUT1T = 0):
135 2 Current Output 2 -
137 2 Current Output 2 Offset -
139 1 Current Output 2 Parameter-
29
140 2 Current Output 2 Span -
142 1 Current Output 2 Output Type. 0=4-
20 mode, 1=0-20 mode.
If overange enable (ANAOUT2OR =
1)
low values can also be set by fault
value, See Fault option (ANAOUT2F)
-
143 1 Current Output 2 Over range Enable.
0=disabled, 1=enabled
144 1 Current Output 2 Fault Option. 0=No
fault, 1=Low fault, 2=High fault.
If high fault (2):
If low fault (1) AND in 4-20 mode
(ANAOUT2T = 0):
145 1 Relay 1. 0=OPEN, 1=CLOSED
146 1 Relay 1 Delay. Holds the relay output
for this set amount of time.
147 1 Relay 1 Function. 0=Disabled,
1=Concentration, 3=Data Valid,
4=System alarm
148 1 Relay 1 Source. The source
parameter number used to evaluated
the relay function.
0 = 3.78 - 20.5, 1 = 0-20.5, high or
High end of range becomes 22 mA
Output ratio becomes 1
Low end of range becomes 3 mA
Output ratio becomes 0.
0 = 3.78 - 20.5, 1 = 0-20.5, high or
High end of range becomes 22 mA
Output ratio becomes 1
Low end of range becomes 3 mA
Output ratio becomes 0.