Ametek 5100 HD User Manual page 108

179
rwf
180 r
181
r
182 rwf
183 rwf
184 rwf
185
r
186 rwf
187 rwf
188 rwf
189 rwf
190
rwf
191 r
192
r
193 rwf
194
rwf
195 rwf
196
rwf
197
rwf
198 rwf
199
rw
200 rw
201 rw
202 rw
203
rw
204
rw
205
rw
206 rw
207 rw
208
rw
209
r
210
r
211
r
212 rw
213
rwf
214 rwf
215
rw
216 rwf
217
rwf
218
rwf
219
rw
6-8 | Model 5100 HD Analyzer
220
rw
char[20] ALYTE2
float ALYTE2CON
float TECTEMP
int16 TECAT
float TECDEVT
float TECDT
float TECHDC
float TECIT
float TECPB
float TECSP
float TECST
float TECHYS
float ELECTEMP
float CELLTEMP
float CELLSP
float CELLDEVT
float NORMTEMP
float NORMPRES
float MAXTEMP
float MINTEMP
uint LOGSAVEINT
char[10] CONCUNIT2
uint ALYTE1RES
uint ALYTE2RES
boolean RELAY1NC
boolean RELAY2NC
boolean RELAY3NC
boolean RELAY4NC
uint16 MENUTO
uint16 PWDTO
uint SYSWARN1
uint SYSWARN2
uint SYSSTWARN
uint16 PTSEED
float MAXTEMP_2
float MINTEMP_2
float REFCONC_2
int16 STATICPT
float STCELLT
float STCELLP
int16 ANAOUT1H
int16 ANAOUT2H
198 10 Analyte 2 Name
208 2 Analyte 2 Concentration
210 2 TEC Temperature Value
212 1 Heater Actuator Type. 0=Reverse,
1=Forward.
213 2 Heater Deviation Tolerance. Ignored if
0. Otherwise high or low limit alarm
are set when value is out bounds of 1
deviation
215 2 Heater Deriviative Time
217 2 Heater Duty Cycle
219 2 Heater Integral Time
221 2 Heater Proportional Band
223 2 Heater Set Point
225 2 TEC Sample Time
227 2 TEC hysterisi
229 2 Electronics Temperature
231 2 Cell RTD1 Filtered value
233 2 Cell Set Point
235 2 Cell Deviation Tolerance. Ignored if 0.
Otherwise high or low limit alarm are
set when value is out bounds of 1
deviation
237 2 Calibration temperature for
concentration compensation.
239 2 Calibration pressure for concentration
compensation
241 2 Max TEC temperature
243 2 Min TEC temperature
245 2 Interval in minutes to save the log
data
247 5 Concentration Unit of Measure for
analyte 2
252 2 Decimal places to use for displaying
analyte 1
254 2 Decimal places to use for displaying
analyte 2
256 1 Normally closed indicator for relay 1.
31
1=Normally closed, 0=Normally open
257 1 Normally closed indicator for relay 2.
1=Normally closed, 0=Normally open
258 1 Normally closed indicator for relay 3.
1=Normally closed, 0=Normally open
259 1 Normally closed indicator for relay 4.
1=Normally closed, 0=Normally open
260 1 Menu timeout. The time that the menu
will navigate to the homescreen after
no activity. 0 is disabled
261 1 Password timeout. The time that a
user logged into the front display
menu will be logged out after no
activity. 0 is disabled
262 2 Temporary cache to miror warnings in
SYSALARM1
264 2 Temporary cache to miror warnings in
SYSALARM2
266 2 system statuc warning
268 1 The seed value for all IIR filters.
269 2 Max TEC temperature 2
271 2 Min TEC temperature 2
273 2 Concentration of Reference call
275 1 Pressure (STCELLP) and temp
(STCELLT) static value usage.
0=neither, 1=use static pressure,
2=use static temperature, 3= use both
276 2 Static cell temperature. Use by
setting STATICPT to 2 or 3
278 2 Static cell pressure. Use by setting
STATICPT to 1 or 3
280 1 Analog output 1, 0 - follow source
during cal, 1 - hold output during cal
281 1 Analog output 2, 0 - follow source
during cal, 1 - hold output during cal
L82