Chapter 4 System Connection; General System Diagram; M615/M635 - Mitsubishi Electric MELDAS 600 Series Connection Manual

CHAPTER 4 SYSTEM CONNECTION

4.1 General System Diagram

4.1.1 M615/M635

3-phase 200V 〜 230VAC
S R T
No fuse breaker(NFB)
(Note 1)
External power
supply unit
PD25A
DCOUT
ACIN
NFB
ON/OFF
24VDC(+)
stabilize d
power supply
FG
OT release switch
EMG
RA
FG
MC
NFB
M C
Servo amplifier
MR-J2-□CT
L1
L2
L3
L11
L21
(Note 1) Refer to "Section 4.3.1 (2)" when not using the PD25A power supply.
(Note 2) After connecting the DO output selected by the user and the application software running on Windows has ended, turn
the external power supply unit's power OFF with the DO output.
(Note 3) Connect the F149 cable pin 8 side [HD ISP] connection to the ISP terminal at the side of CF12.
The target units are only FCU6-MU501 to FCU6-MU514. This is not used by the other units.
(Note 4) CF14 is used only for FCU6-MU515/516. This is not used by the other units.
(Note 5) Normally, use the FCUA-R211 cable for the RIO cable.
If the cable length is short due to bridging between units in the same panel, the SH41 cable can be used.
(Note 6) The DCIN (HEATER) connector is not used with FCU6-KB014.
CHAPTER 4 SYSTEM CONNECTION
4.1 General System Diagram
NC keyboard
FCU6-KB004/KB014
K B
MOUSE
(Note 6)
F070
DCIN
24VDC
(HEATR)
F110
DCIN
(PD25A)
CF01
HR292
F171
/293
CF24
F172
ON/OFF
DCOUT
ON
OFF CF11 CF12
2 4 V D C
F050
CF11 CF12
Control unit
FCU6-MU5**
(M615/M635)
F110
CF01 DCIN EMG CF10
F120
F0 7 0
24VDC DCIN
NC axis
amplifier
spindle
MDS-B -SV
/
T3
MDS-B -SP
T2
L11
L21
P E
L+
L-
CN1 B CN1 A
CN4
CN1 B
CN1 A
Remote I/O unit
DX1**/HR357
RIO1 RIO2
DCIN
F070
FCUA-R211
24VDC
(SH41)
RIO3
(Note 5)
CON1
(Note 2)
POS
P-OFF signal
F020/F021/F022
HANDLE
F030/F031
CF21
F030/F031
CF22
Heater power cable
CF25
CF13
HDD unit
F060
F149
(Note 3)
Wire spliting PCB
HD F140
ISP
HD
F250
CF14
CF14
F130
CFD
F090
LCD
F010
CF10
R301
CF31
R301
CF32
R301
CF33
R301
CF34
Base I/O unit
FCU6-DX***
F040/F041
ENC1
SKIP
SV1 SV2 RIO1 RIO2
RIO
AC reactor
B-AL
(Note 5)
FCUA-R211
(SH41)
Converter
L1
L2
L3
DCIN
L11
L21
L+
L-
MC1 (Note 5)
CN4
F 0 7 0
FCUA-R211
(SH41)
17
Machine control relay/contact
R
R
To next remote I/O unit
FCUA-R211
(SH41)
(Note 5)
Terminator
R-TM
Manual pulse generator
(FCUA-HD60)
RS-232-C
device
(Note 4)
PARALLEL
MOUSE2
F D D
Display unit
FCU6-DUN31/DUC32/DUT31
DI
DI
DO
Electric cabinet
DO
Sensor contact
Max. 8 points
Synchronous feed encoder
Machine control relay/contact
Rem ote I/O card
R
QY231
R
J 4
CSH41A CSH41B
FCUA-R211
(SH41)
(Note 5)
24VDC
MC link B
Terminator
R-TM
Machine control relay/contact
Remote I/O unit
DX1**
RIO1RIO2
FCUA-R211
(SH41)
(Note 5)
24VDC
MC link B
To next remote I/O unit
R
R
To next remote I/O unit
Terminator
R-TM