Intermec JG2010 User Manual page 542

JANUS 2010 Hand-Held Computer User's Manual (4MB)
code39
nugget
DOS NLS support, 8-3
editing a configuration file, 5-13
IC.EXE, using, 5-7
J2010 scanner port as COM2, 6-8
networking, preparing for, 6-12
overview, 5-3
PC cards
overview, 4-14
recording the configuration, 5-16 to 5-26
resetting the Type I PC card drive, 4-7
Scanner Devices (SS) parameter, 10-31
sending commands from a host, 5-12
serial communications parameters, 6-14
summary of methods, 5-6
Z, IRL command, using, 5-12
Connected icon, 2-30
connecting the reader to a device, 6-21
connector end, PC card, illustrated, 4-9, 4-11
contrast, adjusting, 2-27, 12-46
control characters
bar code labels to scan, C-17
full ASCII, list of, C-16
in IC.EXE fields, 5-8
Control mode
adjusting the display, 2-27, B-7, B-12
backlight on and off, 11-4
conventional memory, See also memory
absorbed by loaded software, 10-22
maintained when reader is off, 9-5
saving, 9-7, 9-11
ways to free memory, 3-38, 4-22
conventional memory, described, A-15
conventions for this manual, xxiii
copying files
ATA cards, 4-17
drive C, 8-3
drive C or D, 3-24
flash cards, 4-21
SRAM cards, 4-24
CrossBar network
illustrated, 6-4
Multi-Drop protocol, 6-10, 6-13
using BFT, 6-38
Crosstalk communications application, 9-11
Ctrl key
enabling or disabling functions, 12-70
icon, 2-7, 2-29
using, 2-7
Ctrl P, defining for command override, 11-6
CTS/RTS, set by flow control, 12-56
current configuration, defined, 5-4
cursor
arrow keys, 2-11, 2-25
moving the viewport to, 2-27, 11-20
moving through menus with bar codes, C-23
I-8
helconital
moving to the viewport, 11-20
viewport automatically follows, 2-25
cursor keypad, using, 2-11
Cursor to Viewport reader command, 11-20
D
D drive, See drive D
Data Bits command, 12-42
data files
clearing for IRL, 7-11
storing on drives, 2-44
Data icon, 2-30
date, setting, 1-10
DCM, using with BFT, 6-41
Decode Security command, 12-43
default configuration
CONFIG.SYS loads Interlnk, 10-23
restoring, 5-16
settings, 5-16 to 5-26, A-6 to A-9
deleting files
ATA cards, 4-17
drive C, 3-19, 8-3
flash cards, 4-21
IRL data files, 7-11, 11-9
SRAM cards, 4-24
troubleshooting for flash cards, 10-20
device drivers
HIMEM.SYS, A-16
I/O cards, configuring, 4-22
INTERLNK.EXE, D-3, D-4
list of, 4-27
SRAMDISK.SYS, 3-33, A-16
troubleshooting for flash cards, 10-20
diacritical marks, typing, 8-12
dimensions of the reader, A-3
Direct Hardware Wedge
configuring, 3-41
defined, 3-4, 3-38
enabling, 3-42
Disk Write icon
illustrated, 2-31, 4-24
removing PC cards, 4-13
SRAM cards, low battery, 4-24
display
backlight on and off, 11-4
backlight timeout, configuring, 12-44
buffered for IRL, 12-47
characteristics, configuring, 12-48
contrast, adjusting, 12-46
DOS prompt, adjusting from, 2-27
Graphics mode, described, 2-23