Table of Contents
Advertisement
installation
installation
installation
installation
installation
Extended View Panel Installation
EXTENDED VIEW PANEL INSTALLATION
Extended View Panel Installation
Extended View Panel Installation
Extended View Panel Installation
EXTENDED VIEW PANEL INSTALLATION
1. Construct the sealed rear enclosure to specified width shown below
Extended View Panel Installation
EXTENDED VIEW PANEL INSTALLATION
EXTENDED VIEW PANEL INSTALLATION
EXTENDED VIEW PANEL INSTALLATION
and desired height (see unit manual for detailed framing instructions).
1. Construct the sealed rear enclosure to specified width shown below
1. Construct the sealed rear enclosure to specified width shown below
1. Construct the sealed rear enclosure to specified width shown below
and desired height (see unit manual for detailed framing instructions).
1. Construct the sealed rear enclosure to specified width shown below
and desired height (see unit manual for detailed framing instructions).
and desired height (see unit manual for detailed framing instructions).
and desired height (see unit manual for detailed framing instructions).
2. Locate mounting holes in locations shown below and remove nailing
2. Locate mounting holes in locations shown below and remove nailing
strips (if already installed).
strips (if already installed).
2. Locate mounting holes in locations shown below and remove nailing
strips (if already installed).
2. Locate mounting holes in locations shown below and remove nailing
2. Locate mounting holes in locations shown below and remove nailing
strips (if already installed).
strips (if already installed).
Mounting
holes
Mounting
holes
Mounting
Mounting
holes
holes
3. Attach left and right base panels using 2 screws on each side. Re-
3. Attach left and right base panels using 2 screws on each side. Re-
move drywall finishing edge from right and left side of window open-
move drywall finishing edge from right and left side of window open-
ing using supplied right-angle screwdriver.
3. Attach left and right base panels using 2 screws on each side.
ing using supplied right-angle screwdriver.
3. Attach left and right base panels using 2 screws on each side. Re-
3. Attach left and right base panels using 2 screws on each side. Re-
Remove plasterboard finishing edge from right and left sides of
move drywall finishing edge from right and left side of window open-
move drywall finishing edge from right and left side of window open-
window opening using supplied right-angle screwdriver.
ing using supplied right-angle screwdriver.
ing using supplied right-angle screwdriver.
Attach base panels
Attach base panels
Attach base panels
919-809
919-809
919-809
| City Series ACV60E
68
919-809
Enclosure width:
CV40E - 46-3/4"
Enclosure width:
CV60E - 65-11/16"
Enclosure width:
Enclosure width:
1668 mm
CV40E - 46-3/4"
CV72E - 78"
CV40E - 46-3/4"
Enclosure width:
CV60E - 65-11/16"
CV60E - 65-11/16"
CV40E - 46-3/4"
CV72E - 78"
CV60E - 65-11/16"
CV72E - 78"
CV72E - 78"
Attach base panels
ACV60E CITY SERIES
4. Move unit into framed opening at desired height and level unit on all
sides. Connect gas and electrical (see manual).
4. Move unit into framed opening at desired height and level unit on all
4. Move unit into framed opening at desired height and level unit on all
4. Move unit into framed opening at desired height and level unit on
sides. Connect gas and electrical (see manual).
4. Move unit into framed opening at desired height and level unit on all
sides. Connect gas and electrical (see manual).
all sides. Connect gas and electrical (see manual).
sides. Connect gas and electrical (see manual).
5. Install a second stud as shown. The distance from first to second
stud should be 8-1/2".
5. Install a second stud as shown. The distance from first to second
5. Install a second stud as shown. The distance from first to second
stud should be 8-1/2".
5. Install a second stud as shown. The distance from first to second
stud should be 8-1/2".
5. Install a second stud as shown. The distance from first to second
stud should be 8-1/2".
stud should be 216 mm.
Install second stud--8.5" out from first stud
Install second stud--8.5" out from first stud
Install second stud--8.5" out from first stud
Install second stud--8.5" out from first stud
6. Secure base panels in place with 5 screws on each side.
Install second stud--216 mm out from first stud
6. Secure base panels in place with 5 screws on each side.
6. Secure base panels in place with 5 screws on each side.
6. Secure base panels in place with 5 screws on each side.
6. Secure base panels in place with 5 screws on each side.
Secure base panels
Secure base panels
Secure base panels
Secure base panels
Secure base panels
1
1
1
1
CITY SERIES
CITY SERIES
CITY SERIES
CITY SERIES
8-1/2"
8-1/2"
8-1/2"
8-1/2"
8-1/2"
8.5" from stud center to
stud center
8.5" from stud center to
stud center
8.5" from stud center to
8.5" from stud center to
stud center
stud center
216 mm from stud center
to stud center
07.05.17
07.05.17
07.05.17
07.05.17
Advertisement
Table of Contents
