Regency Fireplace Products City Series Manual

Regency Fireplace Products City Series Manual

Direct vent gas fireplace
Hide thumbs Also See for City Series:

Advertisement

Quick Links

City Series CB50E Direct Vent Gas Fireplace
MODEL
Fuel Type
Minimum Supply Pressure
Manifold Pressure - High
Manifold Pressure - Low
Orifice Size -Altitude 0-4500 ft
Minimum Input
Altitude 0-4500 ft. (0-1372m)
Maximum Input
Altitude 0-4500 ft. (0-1372m)
Vent Sizing
CSA P.4.1.
NOTE: This model comes with a 5" inner and 8" outer collar (127 mm x 203 mm) which must be reduced to 4" inner x 6-5/8" outer
(102 mm x 168 mm) in all applications when used as a power vent system. See power vent manual for details.
Dimensions - Bay Install
Note: Height Dimension is taken with leveling legs fully inserted and may vary depending on the height of the leveling legs, when
unscrewed or extended.
Dimensions will appear as (inches)" / (metric) mm throughout this manual. The inches are rounded to the nearest 1/16" when con-
verted, when greater accuracy is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.
CB50E-NG
Natural Gas
5" W.C. (1.25 kPa)
3.8" W.C. (0.94 kPa)
10.5" W.C. (2.62 kPa)
1.1" W.C. (0.27 kPa)
2.9" W.C. (0.72 kPa)
# 36 DMS
19,000 Btu/h
(5.56 kW)
35,000 Btu/h
(10.25 kW)
5" Inner / 8" Outer
57.49%
11
48
"
11
16
1236mm
288mm
8"
5"
203mm
127mm
11
5
48
"
11
"
16
16
1236mm
288mm
8"
5"
203mm
127mm
1
61
"
16
1551mm
1
61
"
16
60"
1551mm
1524mm
60"
1524mm
CB50E-LP
Propane
11" W.C. (2.73 kPa)
# 52 DMS
17,000 Btu/h
(4.98 kW)
33,000 Btu/h
(9.66 kW)
5" Inner / 8" Outer
60.55%
5
"
16
20
532mm
20
519mm
City Series CB50E Direct Vent Gas Fireplace |
15
20
"
16
532mm
7
20
"
16
15
519mm
"
16
7
"
16
5
7
16
"
4
"
8
16
423mm
112mm
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the City Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Regency Fireplace Products City Series

  • Page 1 Note: These units are non-load bearing. ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS. City Series CB50E Direct Vent Gas Fireplace |...
  • Page 2: Gas Connection - Bottom Of Unit

    Gas Connection - Bottom of Unit FRONT OF UNIT GAS VALVE 8 " OPENING AT UNIT BASE BACK OF UNIT Gas Connection - Side of Unit | City Series CB50E Direct Vent Gas Fireplace...
  • Page 3 Electrical Connection - Bottom of Unit Electrical Connection - Side of Unit City Series CB50E Direct Vent Gas Fireplace |...
  • Page 4 Note: These units are non-load bearing. ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS. | City Series CB50E Direct Vent Gas Fireplace...
  • Page 5 Fire hazard is an extreme risk if these clearances (air space) to combustible materials are not adhered to. It is of greatest importance that this fireplace and vent system be installed only in accordance with these instructions. City Series CB50E Direct Vent Gas Fireplace |...
  • Page 6 Floor to ceiling with top opening Full framing with vents in front/2 sides or top opening opening Full framing with low vents in front or 2 sides Full framing with vents in front or 2 sides | City Series CB50E Direct Vent Gas Fireplace...
  • Page 7 (air space) to combustible materials are not adhered to. It is of greatest importance that this fireplace and vent Top View system be installed only in accordance with these instructions. Alcove City Series CB50E Direct Vent Gas Fireplace |...
  • Page 8: Mantel Clearances

    To Bottom of Top of Fireplace Fireplace Opening Opening 18" (457 mm) Mantel Leg Clearances (Non Glass Side When Installed as a Left/Right Corner) Combustible mantel leg clearances as per diagram: MANTEL LEG 0" | City Series CB50E Direct Vent Gas Fireplace...
  • Page 9 The framing depth will need to change based on the thickness of the material (example: 20-7/16 framing depth + 1/2 drywall = 20-15/16") Max 2 x 6 City Series CB50E Direct Vent Gas Fireplace |...
  • Page 10 Example B : 71 1/4" framing width + 1/2" drywall = 71 3/4". Example C : 20-7/16" framing depth + 1/2" drywall = 20-15/16". Max 2 x 6 | City Series CB50E Direct Vent Gas Fireplace...
  • Page 11 Example B : 71 1/4" framing width + 1/2" drywall = 71 3/4". Example C : 20-7/16" framing depth + 1/2" drywall = 20-15/16". Max 2 x 6 City Series CB50E Direct Vent Gas Fireplace |...
  • Page 12: Recessed Install

    See Mantel clearance in manual Screws must not MAX DEPTH 36" (914 MM) penetrate unit more HEARTH than 1/2". Adhere to "No Screw" zones painted on unit Glue can be used as an alternative | City Series CB50E Direct Vent Gas Fireplace...
  • Page 13 Note: The TV mounting bracket cannot be secured directly to the appliance. It must be secured to framing. The TV depicted in the picture may need to be higher depending on the style of TV mounting bracket used. City Series CB50E Direct Vent Gas Fireplace |...
  • Page 14 5. Flex system can only be used up to a maximum Vent Guard - if required* continuous vent length of up to 10 feet. If longer runs (Part #946-604/P) are required, rigid pipe must be used. 5" (127 mm) 8" (203 mm) | City Series CB50E Direct Vent Gas Fireplace...
  • Page 15 1-3/8"(35mm) french Vinyl Siding and fasten with the 3 screws. Wall Thimble Screws Fourrures en bois Diagram 2 City Series CB50E Direct Vent Gas Fireplace |...
  • Page 16 Firestops are required at each floor level and whenever passing through a wall. • A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes. | City Series CB50E Direct Vent Gas Fireplace...
  • Page 17: Horizontal Terminations

    Metal Products Ameri Vent Direct Vent, Security Secure Vent , ICC Excel, Selkirk Direct-Temp. AstroCap is a proprietary trademark ® of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. City Series CB50E Direct Vent Gas Fireplace |...
  • Page 18 Diagram 4 not covered under warranty. *As specified in CSA B149 Installation Code. Local codes or Horizontal runs of vent must be supported regulations may require different clearances. | City Series CB50E Direct Vent Gas Fireplace...
  • Page 19: Horizontal Venting With Two (2)

    Restrictor Set 0 - Factory Setting 6' Min. 5' Max. 11' Min. 8' Max. required. 7' Min. 6' Max. 12' Min. 9' Max. Restrictor Set 0 - Factory Setting City Series CB50E Direct Vent Gas Fireplace |...
  • Page 20: Vertical Terminations

    , ICC Excel, Olympia Ventis DV, Selkirk Direct-Temp. AstroCap is a proprietary trademark ® of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. | City Series CB50E Direct Vent Gas Fireplace...
  • Page 21 If no offsets are used, the maximum Set 4: 1-1/2" (38 mm) run is per the chart on this page. open Set 3: 2-3/8" (60 mm) open Min. length of pipe between elbows: 12" (305 mm) City Series CB50E Direct Vent Gas Fireplace |...
  • Page 22 Please note min. 1 foot between 6' Min. 7' Max 9' Min. elbows is 7' Min. 8' Max 10' Min. required. Lengths do not include elbow indicated Restrictor Set 0 - Factory Setting | City Series CB50E Direct Vent Gas Fireplace...
  • Page 23: Vertical Termination

    4 screws/nails. If more than one is required, these can be purchased separately. The ceiling firestop/firestop spacer may be cut down to size if this shield is too high for the application. 11" Ceiling firestop Diagram 2 920-385 Page 1 04.29.21 City Series CB50E Direct Vent Gas Fireplace |...
  • Page 24: Installation

    Note: Any closets or storage spaces which the vent passes through must be enclosed. Diagram 3a Diagram 3a Diagram 3a 920-328 09.18.20 City Series ACB60E | 61 920-328 09.18.20 City Series ACB60E | 61 920-385 Page 2 04.29.21 | City Series CB50E Direct Vent Gas Fireplace...
  • Page 25 (0.91 m) to avoid excessive stress and sagging of the vent pipe. Wall straps are provided (3 in total) for this purpose. All round/plumbers strapping may also be used if further supports are required. City Series CB50E Direct Vent Gas Fireplace |...
  • Page 26 Diagram 1a The ceiling firestop/firestop spacer may be cut Diagram 1a Ceiling firestop down to size if it is too high for the application. Diagram 1a | City Series CB50E Direct Vent Gas Fireplace 920-328 920-337 10.05.20 10.05.20 920-338 10.05.20...
  • Page 27 * Clearance in accordance with local installation codes and the requirements of the gas supplier 3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly 3 feet (91cm) above - if within 10 feet (3m) horizontally City Series CB50E Direct Vent Gas Fireplace |...
  • Page 28 VDV-UAA04 Ceiling Support 4DT-CS 4DSP 4DFSP SV4SD TM4-RDS VDV-SCR04 Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TM4-SDS VDV-CSS04 Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM TM-SWS VDV-WS04 *Not available at Regency | City Series CB50E Direct Vent Gas Fireplace...
  • Page 29 Metal-Fab Sure Seal: www.mtlfab.com 24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com 36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com 48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm) Olympia Ventic DV: www.olympiachimney.com City Series CB50E Direct Vent Gas Fireplace |...
  • Page 30: Vent Restrictor Position

    Part # of the Power Vent System manual is 920-544. Minimum Vent Clearances to Combustibles Horizontal Top 3" (76mm) Horizontal Side 2 " (51mm) Horizontal Bottom 2" (51mm) Power Vent System Vertical Vent 2" (51mm) Manual | City Series CB50E Direct Vent Gas Fireplace...
  • Page 31 Vent Restrictor Position No vent restrictor required. No vent restrictor required. Set 0 Set 0 Fully open Fully open Factory Set Factory Set 3 1 8 " City Series CB50E Direct Vent Gas Fireplace | 920-210b 09.22.20 3 1 8 "...
  • Page 32 • • Minimum 4' (1.2 m) from the unit prior to terminating. Minimum 4' (1.2 m) from the unit prior to terminating. Vent Restrictor Position No vent restrictor required. Set 0 Fully open Factory Set | City Series CB50E Direct Vent Gas Fireplace 3 1 8 "...
  • Page 33 THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN W nit to inline PV Min. 2' (0,61 m) from inline PV to termination cap Min. 4' (1.22 m) from top of unit to inline PV City Series CB50E Direct Vent Gas Fireplace | 920-210b 09.22.20...

This manual is also suitable for:

Cb50e seriesCb50e-ngCb50e-lp

Table of Contents