Table of Contents
Advertisement
EDIT DATA DUMPING TO/LOADING FROM AN EXTERNAL DEVICE
The edit data entered in the EDL memory can be transmitted to an external source via the RS-232C connector. For instance,
operation and control can be exercised in a wide range of systems as shown below by uploading data to a computer or down-
loading data from a computer.
1) Off-line editing is possible, and edit data can be used by an on-line system.
2) Edit data can be stored on a hard disk or floppy disk.
3) The edit data can be checked on the computer CRT screen or in printout form.
AJ-LT85
<Note>
EDL dumping and loading operations cannot be performed while the CONTROL switch is at the REMOTE or EXT VTR setting.
Steps taken for dumping
V T R 1
POWER
EDIT MODE
REC
CONTROL
PREROLL
AUDIO
SPEAKER/
AUDIO
OFF
ON
INHIBIT
REMOTE
SYNCHRO
MONITOR
HEADPHONES
SWAP
CF
CH1
V1
SWAP
REC
7
-
-
-
-
-
-
-
-
ON
-
V
A1
LOCAL-
5
-
ON
-
-
MIX
-
V1•2
-
-
NORM
-
ASMBL
REC
-
OFF
-
3
-
OFF
-
-
CH2
-
V2
-
-
MIX
-
DIAG
1ST EDIT
DUMP
VTR1 VTR2
VTR1 VTR2
VTR1 VTR2
EXT VTR
RESET
CH1
CH2
LAST
PLAY
STILL
REW
FF
SPLIT
EDIT
STOP
BS
FS
CLEAR
STB OFF
TRACK
EVENT
VTR1
GO TO
IN
OUT
IN
OUT
RECALL
PB
AUDIO LEVEL
ENTRY / SHIFT
PREVIEW
AUTO
ALL STOP
EDIT
REVIEW
MULTI
! Set up the computer or other external unit to receive the data.
@ Press the DUMP (SHIFT + A1) button. The A1 button lamp now flashes, and the event number sent is displayed in the
counter area. The format set in the EDL FORMAT set-up item is selected as the output format.
# The operation is completed when all the edit data in the EDL memory has been transferred. To stop the transfer at any time,
press the ALL STOP button.
Steps taken for loading
V T R 1
POWER
AUDIO
SPEAKER/
AUDIO
EDIT MODE
REC
CONTROL
PREROLL
OFF
ON
MONITOR
HEADPHONES
SWAP
INHIBIT
REMOTE
SYNCHRO
REC
7
-
CF
-
-
CH1
-
V1
-
-
SWAP
-
-
ON
-
ASMBL
V
A1
LOCAL-
5
-
ON
-
-
MIX
-
V1•2
-
-
NORM
-
REC
-
OFF
-
3
-
OFF
-
-
CH2
-
V2
-
-
MIX
-
DIAG
VTR1 VTR2
1ST EDIT
DUMP
EXT VTR
VTR1 VTR2
VTR1 VTR2
RESET
CH1
CH2
LAST
PLAY
STILL
REW
FF
SPLIT
EDIT
STOP
STB OFF
TRACK
EVENT
BS
FS
CLEAR
VTR1
GO TO
IN
OUT
IN
OUT
RECALL
PB
AUDIO LEVEL
ENTRY / SHIFT
PREVIEW
AUTO
ALL STOP
EDIT
REVIEW
MULTI
! Press the LOAD (SHIFT + A2) button. The A2 button lamp now flashes.
@ The data is sent from the computer or other external unit. The format in which the data is sent must be the format which was
set for set-up menu item No.208 (EDL FORMAT). The event number being received is displayed in the counter area.
# The operation is completed when the computer stops transmitting the data or when the EDL memory is full. To stop the
transfer at any time, press the ALL STOP button.
<Notes>
1. External device settings are required for dumping or loading data.
2. Unless the data is either the corrected or edited EDL data or in a format which is supported by this unit, not only will it be
impossible for the data to be received but the unit may malfunction as well. For this reason, users without a detailed knowl-
edge of personal computers or EDL data should refrain from conducting these operations.
DUMP
RS-232C
LOAD
V T R 2
OPERATION MODE
VTR2 AUDIO
EDIT
INPUT SELECT
INT
VTR1
EXT
EXT
REC
EDIT
A2
TC
CH1
CH2
SEPARATE
REC
LOAD
EDL
STORE
MENU
RESET
CH1
CH2
COUNTER
CTL
PLAY
STILL
FF
TC
REW
UB
STOP
STB OFF
VTR2
PB
AUDIO LEVEL
V T R 2
OPERATION MODE
VTR2 AUDIO
EDIT
INPUT SELECT
INT
VTR1
EXT
EXT
REC
EDIT
A2
TC
SEPARATE
CH1
CH2
REC
LOAD
EDL
STORE
MENU
RESET
CH1
CH2
COUNTER
CTL
PLAY
STILL
TC
REW
FF
UB
STOP
STB OFF
VTR2
PB
AUDIO LEVEL
Computer
54
Store
Use
Hard disk or
floppy disk
Advertisement
Table of Contents
