Table of Contents
Advertisement
ASSEMBLY INSTRUCTIONS
3BCT/Chopper Reel Installation
(Option)
NOTE
Refer to
See Figures 2-14
for Standard 3BCT/Chopper Reel Placement.
Refer to
See Figures 2-24
for Hydraulic 3BCT/Chopper Reel Placement.
1. Model 2111-11, attach the harrow extension LT and
RT to plates on end of frame with 3/4 x 7 bolts, 3/4 x
2-1/2 bolts and 3/4 lock nuts
2. Attach the combo harrow mount arm long
assemblies on rear of center frame, RT side, and
short arm assemblies, LT side, to plates on rear of
center frame,with 3/4 x 2-1/2 bolts, 3/4 flat washers,
3/4 lock nuts
See Figures
3. Remove the 5/8 x 3-11/16 x 6-3/8 u-bolts, 5/8 flange
lock nuts, harrow stiffner plates from harrow
adjustment tubes.
4. Attach the harrow tine assemblies, secure with the
u-bolts, harrow stiffner plates, nuts that were just
removed as shown
See Figures
5. Remove the 3/4 x 5-1/2bolts, 3/4 lock nuts, gangbar
mount plates from harrow mount arms.
6. Attach the reel assemblies, secure with the gangbar
mount plates, 3/4 x 5-1/2bolts, 3/4 lock nuts, that
were just removed as shown
7. Model 2112-09, remove the 1 x 7-1/2 bolts and 1 lock
nuts. Attach the wrench mount with 1 x 7-1/2 bolt and
1" lock nut to the combo harrow mount arm.
Figures 3-19
or
See Figures 3-20
location of the wrench mount.
8. Models 2112-11-13-15 attach the wrench mount with
the 1/2 x 8-1/2 bolts, 1/2 flat washer, 1/2 lock nuts to
the combo harrow mount arm
See Figures 3-26
for proper location of the wrench
mount.
9. On hydraulic 3BCT/Chopper Reel option, install the
hose mount plate with the 1/2 x 8-1/2 bolt, 1/2 flat
washer, 1/2 lock nut, the hose clamp attaches with
3/8 x 1-1/2 bolt, 3/8 flat washer, 3/8 lock nut
Figures
3-23.
See Figures 3-27
of the wrench mount.
10. On hydraulic 3BDT/Chopper Reel option, install the 8
port manifold to manifold mount with 1/2 x 3-1/2
bolts, 1/2 lock nuts as shown
3-32
through
See Figures 2-23
through
See Figures 2-33
See Figures
3-23.
3-23.
3-23.
See Figures
3-23.
See
for proper
See Figures
3-23.
See
for proper location
See Figures
3-21.
8 PORT MANIFOLD,
1/2 X 3-1/2 BOLT,
1/2 LOCK NUT
Figure 3-21: 8 Port Manifold Installation
11. On hydraulic 3BDT/Chopper Reel option, attach
hoses down through the slotted holes of combo
harrow mount arm to cylinders as shown
Figures
3-22. Route hoses from base end of cylinder
to top set of holes of 8 port manifold, rod end to
bottom holes of manifold.
SLOTTED HOLES
ROD END
CYLINDER
Figure 3-22: Hose to Cylinder Installation
12. On hydraulic 3BCT/Chopper Reel option,
Figures 3-24
through
hydraulic installation.
MANIFOLD MOUNT
BRACKET
See
6"
BASE END
CYLINDER
See
See Figures 3-27
for proper
F-1102-0721
Advertisement
Table of Contents
