Introduction and Safety Information Introduction The Landoll Model 2112 CC is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.
INTRODUCTION AND SAFETY INFORMATION Understanding Safety Decal Safety Statements 1. Examine safety decals and be sure you have the correct safety decals for the implement. You will find various types of safety information on the 2. Keep these signs clean so they can be observed following pages and on the machine signs (decals) readily.
INTRODUCTION AND SAFETY INFORMATION High Pressure Fluid Safety 6. Attach the safety chain to the tractor recommended drawbar support. Provide only enough slack in the 1. Escaping fluid under pressure can be nearly invisible chain for turning. Do not attach the safety chain to an and have enough force to penetrate the skin causing intermediate support.
INTRODUCTION AND SAFETY INFORMATION Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.
10 days of able to follow the suggestions made. Please take time to purchase or lease, in order to be on file at Landoll and understand the proper maintenance schedule and SAFE eligible for Warranty. operation of your equipment.
The sole obligation ofLandoll Company, LLC under this warranty shall be limited to repairing or replacing, at its option, part(s) which shall be identified to Landoll Company, LLC by way of a pre-authorized Landoll Company, LLC e-mail Warranty Claim Form Warranty, expressed or implied, will be denied on any product not properly registered with the Landoll Company, LLC Warranty Department within ten (10) days of the first retail sale.
Page 11
Landoll Company, LLC , loss of anticipated profits, transportation expenses due to repairs, non-operation or increased expense of...
STANDARD SPECIFICATIONS Model Specifications 2112 Coulter Chisel W/Auto Reset Shanks Model Number 2112-9 2112-11 2112-13 2112-15 Working Width 11'-3” 13'-9” 16-10” 18'-9” Transport Width 11'-9” 14'-4” 16'-10” 19'-4” Transport Height Number of Blades Number of Bearings Estimated Weight 15,860 lbs. 16,710 lbs.
STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
Page 15
STANDARD SPECIFICATIONS Table provided for general use. NOTES:...
Page 16
STANDARD SPECIFICATIONS 5-1/2" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATES LOCATION OF OPTIONAL LT TWISTED SHOVELS Figure 2-4: Auto Reset Shank Placement 2112-09 F-1102-0721...
Page 17
STANDARD SPECIFICATIONS 5-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATE LOCATION OF OPTIONAL LT TWISTED SHOVELS Figure 2-5: Auto Reset Shank Placement 2112-11...
Page 18
STANDARD SPECIFICATIONS 5-1/2" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATE LOCATION OF OPTIONAL LT 20-1/2" 20-1/2" TWISTED SHOVELS Figure 2-6: Auto Reset Shank Placement 2112-13 2-10 F-1102-0721...
Page 19
STANDARD SPECIFICATIONS 5-9/16" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL 5-1/2" 5-1/2" RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATE LOCATION OF OPTIONAL LT TWISTED SHOVELS Figure 2-7: Rigid Shank Placement 2112-13 2-11...
Page 20
STANDARD SPECIFICATIONS NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATE LOCATION OF OPTIONAL LT TWISTED SHOVELS 5-1/2" 5-9/16" 5-1/2" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" Figure 2-8: Auto Reset Shank Placement 2112-15 2-12 F-1102-0721...
Page 21
STANDARD SPECIFICATIONS NOTE: RED SHANK MOUNTS INDICATES LOCATION OF OPTIONAL RT TWISTED SHOVELS, BLUE SHANK MOUNTS INDICATE LOCATION OF OPTIONAL LT TWISTED SHOVELS 5-9/16" 5-1/2" 5-1/2" 5-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" 20-1/2" 20-1/2" 5-1/2" 5-1/2" Figure 2-9: Rigid Shank Placement 2112-15 2-13...
Chapter 3 Assembly Instructions It is very important that your new 2112 Coulter Chisel be WARNING properly assembled, adjusted and lubricated before use. Illustrations to assist with the assembly process are Do not attempt to lift heavy parts (such as the provided in “Standard Specifications”...
ASSEMBLY INSTRUCTIONS Center Frame Assembly 5. Attach smv mount, manifold mount to rear tube of center frame with 5/8 x 6 bolts and 5/8 lock nuts. 2112-09-11 6. Install the smv, SIS decal bracket to smv mount with 1/4 x 1 bolts and 1/4 lock nuts. Install the SIS 20mph ...
Page 41
ASSEMBLY INSTRUCTIONS SMV MOUNT, MANIFOLD MOUNT, 5/8 X 6 BOLT, 5/8 LOCK NUT NOTE: REAR 8 PORT MANIFOLD USED ON OPTIONAL HYDRAULIC SMV, REEL ATTACHMENT ONLY SIS DECALBRACKET, 1/4 X 1 BOLT, 1/4 LOCK NUT 8 PORT MANIFOLD, 1/2 X 3-1/2 BOLT, 1/2 LOCK NUT HUB/SPINDLE ASSEMBLY...
ASSEMBLY INSTRUCTIONS Center Frame Assembly 5. Attach smv mount, manifold mount to rear tube of center frame with 5/8 x 6 bolts and 5/8 lock nuts. 2112-13-15 6. Install the smv, SIS decal bracket to smv mount with 1/4 x 1 bolts and 1/4 lock nuts. Install the SIS 20mph ...
Page 43
ASSEMBLY INSTRUCTIONS SMV, SIS DECALBRACKET, NOTE: REAR 8 PORT MANIFOLD 1/4 X 1 BOLT, USED ON OPTIONAL HYDRAULIC 1/4 LOCK NUT REEL ATTACHMENT ONLY 8 PORT MANIFOLD, 1/2 X 3-1/2 BOLT, 1/2 LOCK NUT CENTER FRAME WELDMENT ASSEMBLY RT 2112 FRONT MANIFOLD, 1/2 X 4 BOLT, 1/2 LOCK NUT SMV MOUNT, MANIFOLD...
ASSEMBLY INSTRUCTIONS Center Frame Lift Assembly NOTE 2112-13-15 The valve stems will face outwards. 12. Attach the rear of the depth stop assembly using a WARNING 5/8 x 2-1/2 bolt and 5/8 lock nut. 13. Attach the front of depth stop assembly with slide pad Do not attempt to lift heavy parts (such as the between top side of bracket on rear side of front frame, coulter gangs, wheel lift, and pull hitch)
Page 45
ASSEMBLY INSTRUCTIONS DEPTH STOP ASSY, LIMIT VALVE, SLIDE PAD, DEPTH STOP GUIDE 5/16 X 5-1/2 BOLT, 5/16 LOCK NUT 4 X 16 CYLINDER 5/8 X 2-1/2 BOLT, 5/8 LOCK NUT 4 X 16 STAND BEARING LIFT CAP CYLINDER 3/4 X 2 BOLT, 3/4 LOCK NUT HUB/SPINDLE CENTER LIFT...
ASSEMBLY INSTRUCTIONS Hitch Installation 5. Install the hose holder bracket to the front of the hitch assembly with 3/4 x 2 bolt, 3/4 flat washer and 3/4 1. Attach the hitch assembly to the front of the center lock nut. frame using hitch pins, 1”...
Page 47
ASSEMBLY INSTRUCTIONS HOSE STORAGE PLATE, 1 X 11 BOLT, 1 FLAT WASHERS 1 LOCK NUT WING NUT, HOSE CLAMP LONG, 3/8 NUT, 3/8 X 5 BOLT ALL THREAD HITCH PIN, STOR-A-WAY, 1/2 X 2-1/4 GROOVE PIN, 1/4 X 1 BOLTS, 1”...
ASSEMBLY INSTRUCTIONS Hitch Leveling Installation 3. Connect front of leveler tube weldment to the rear hole of leveler tower using hitch pin, 1 lock nuts and 1. Connect narrow end of the leveler tower to the top 1/2 x 2-1/4 groove pin. hole on rear of the hitch assembly using 1-1/4-7 x 4.
Page 49
ASSEMBLY INSTRUCTIONS LEVELER TUBE WELDMENT HITCH PIN, 1/2 X 2-1/4 GROOVE PIN, 1” LOCK NUT LEVELER TOWER HITCH PIN, 1/2 X 2-1/4 GROOVE PIN, 1” LOCK NUT NOTE: ATTACH LEVER TUBE 1-1/4 X 9-1/2 BOLT, WELDMENT TO MIDDLE SET RADIUS 1-1/4 LOCK WASHER ASSEMBLY OF HOLES IN CENTER LIFT...
ASSEMBLY INSTRUCTIONS Coulter Gang Installation 2. Attach the base end of the 3-3/4 x 8 cylinder to the coulter spring assembly attached to the left center frame weldment using the clevis pins and roll pins DANGER provided with cylinder. 3.
Page 51
ASSEMBLY INSTRUCTIONS CYLINDER 4 X 8, DEPTH GAUGE PINS PROVIDED GUIDE, 5/8 X 6-11/16 WITH CYLINDER X 7-1/2 U-BOLT, 1 FLANGE LOCK NUT, DEPTH GAUGE MOUNT, 5/8 X 7-11/16 X 5-1/2 U-BOLT, 1 FLANGE LOCK NUT, DEPTH GAUGE INDICATOR, DEPTH GAUGE DECAL, 1/2 X 5 BOLT, 1/2 LOCK NUT CYLINDER 3-3/4 X 8,...
Page 52
ASSEMBLY INSTRUCTIONS GANG ASSEMBLY GANG ASSEMBLY LH 9 BLADE RH 10 BLADE 2112-09 GANG ASSEMBLY GANG ASSEMBLY LH 11 BLADE RH 12 BLADE 2112-11 GANG ASSEMBLY GANG ASSEMBLY LH 13 BLADE RH 14 BLADE 2112-13 GANG ASSEMBLY GANG ASSEMBLY LH 15 BLADE RH 16 BLADE 2112-15 Figure 3-10: Coulter Gang Placement...
Page 53
ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-15...
Page 54
ASSEMBLY INSTRUCTIONS Auto Reset Shank Installation 2. Install the 2” cast flat point onto shanks with 1/2 x 3-3/4 bolts, 1/2 hd flat washers and 1/2 heavy nuts. 1. Attach each shank to each auto reset clamp 3. Install the 2” cast point onto shanks with 1/2 x 3-1/4 assembly using 3/4 x 4 bolt, lock nut in bottom hole bolts, 1/2 hd flat washers and 1/2 heavy nuts.
Page 55
ASSEMBLY INSTRUCTIONS AUTO RESET CLAMP ASSEMBLY LT AUTO RESET CLAMP ASSEMBLY RT 3/4 X 5 BOLT, 3/4 LOCK NUT 3/4 X 4 BOLT, 3/4 LOCK NUT SHANK 2” CAST FLAT POINT 1/2 X 3-3/4 BOLT, 1/2 HD FLAT WASHER, 1/2 HEAVY NUT 2”...
ASSEMBLY INSTRUCTIONS Rigid Shear Bolt Clamp Shank 2. Install the 2” cast flat point onto shanks with 1/2 x 3-3/4 bolts, 1/2 hd flat washers and 1/2 heavy nuts. Installation 3. Install the 2” cast point onto shanks with 1/2 x 3-1/4 1.
Page 57
ASSEMBLY INSTRUCTIONS 12” OFFSET SHEAR BOLT CLAMP 8” OFFSET 5/8 X 5-1/2 GR. 8 BOLT, SHEAR BOLT CLAMP 5/8 X 3/4 X 1-1/4 BUSHINGS, 5/8 FLAT WASHERS, 5/8 LOCK NUTS 3/4 X 4 BOLT, 3/4 LOCK NUT 1/2 X 3-3/4 BOLT, 1/2 HD FLAT WASHER, 1/2 HEAVY NUT 2”...
ASSEMBLY INSTRUCTIONS Hydraulic Installation See Figures 3-13 through See Figures 3-14 for lift hydraulic installation. See Figures 3-15 through See Figures 3-16 coulter hydraulic installation. 3-20 F-1102-0721...
Page 59
ASSEMBLY INSTRUCTIONS 3/8” X 96” (2112-9-11) 4 X 16 3/8” X 128” (2112-13-15) CYLINDER HOSE 3/8” X 76” (2112-9-11) 4 X 16 3/8” X 110” (2112-13-15) CYLINDER HOSE 90° #8 ADAPTER DETAIL A 3/8” X 108” (2112-9-11) 1/2” X 31” 3/8”...
Page 60
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: RUN HOSES NOTE: RUN HOSES THROUGH ALL HOSE THROUGH ALL HOSE CLAMPS AND LOOPS CLAMPS AND LOOPS Figure 3-14: Lift Hydraulic Layout 3-22 F-1102-0721...
Page 61
ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-23...
Page 62
ASSEMBLY INSTRUCTIONS 4 X 8 3/8” X 36” (2112-09-11) CYLINDER 3/8” X 54 (2112-13-15) 90° #8 1/16” HOSE RESTRICTOR ADAPTER (NOTE: LOCATION ROD END THIS CYLINDER ONLY) 3/8” X 116” (2112-09-11) 90° #8 3/8” X 128 (2112-13-15) ADAPTER HOSE DETAIL A 3/8”...
Page 63
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: ROUTE HOSES NOTE: ROUTE HOSES LIKE THIS WAY LIKE THIS WAY FOR MODELS 2112-13-15 FOR MODELS 2112-13-15 NOTE: LOCATION OF 1/16” NOTE: ROUTE HOSES RESTRICTOR LIKE THIS WAY FITTING FOR MODELS 2112-09-11 Figure 3-16: Coulter Gang Hydraulic Layout...
Page 64
ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-26 F-1102-0721...
ASSEMBLY INSTRUCTIONS LED Light Installation IMPORTANT Make sure lights are positioned for maximum NOTE visibility from the rear See Figures 3-19. Refer to See Figure 3-19 for light bracket and wiring 5. Install the rear harness to the rear tube of frame harnesses placement.
Page 67
ASSEMBLY INSTRUCTIONS TAIL LIGHT MOUNT, RED AG LAMP, NOTE: REAR HARNESS MOUNT BRACKET, REFLECTOR MOUNT, THROUGH LIGHT BRACKET 1/2 X 10 BOLTS, 1/4 X 1-1/2 BOLTS, ASSEMBLY TUBE LH 1/2 FLAT WASHERS, 34” HARNESS LOCK NUTS 1/2 LOCK NUTS EXTENSIONS AG FLASHER CONTROL MODULE, LIGHT BRACKET ASSEMBLY RH,...
Page 68
ASSEMBLY INSTRUCTIONS MAIN LIGHT HARNESS, 7-PIN CONNECTOR NOTE: SECURE LIGHT TO TRACTOR HARNESSES WITH TIES STRAPS AS NEDDED MAIN LIGHT TO KEEP CLEAR OF ANY HARNESS MOVING PARTS NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE LOOPS ALONG HYDRAULIC HOSES MAIN LIGHT HARNESS NOTE: AG FLASHER MODULE MOUNTS...
Page 69
ASSEMBLY INSTRUCTIONS NOTE: SECURE LIGHT HARNESSES WITH TIE STRAPS AS NEDDED MAIN LIGHT HARNESS, TO KEEP CLEAR OF ANY 7-PIN CONNECTOR MOVING PARTS TO TRACTOR MAIN LIGHT HARNESS NOTE: RUN LIGHT HARNESSES NOTE: AG FLASHER THROUGH ALL MODULE MOUNTS HOSE LOOPS UNDER RH TAIL ALONG HYDRAULIC LIGHT MOUNT...
ASSEMBLY INSTRUCTIONS 3BCT/Chopper Reel Installation (Option) NOTE Refer to See Figures 2-14 through See Figures 2-23 for Standard 3BCT/Chopper Reel Placement. Refer to See Figures 2-24 through See Figures 2-33 for Hydraulic 3BCT/Chopper Reel Placement. 1. Model 2111-11, attach the harrow extension LT and RT to plates on end of frame with 3/4 x 7 bolts, 3/4 x 2-1/2 bolts and 3/4 lock nuts See Figures...
Page 71
ASSEMBLY INSTRUCTIONS NOTE: MODEL 2112-09 HARROW ADJ WRENCH, QUICK HITCH PIN HYD COMBO ARM SHORT WRENCH MOUNT, 1 X 7-1/2 BOLT, 1 LOCK NUT HARROW EXTENSION LT RT, HOSE CLAMP, 3/4 X 7 BOLTS, 3/8 X 1-1/2 BOLT, 3/4 X 2-1/2 BOLTS, 3/8 FLAT WASHER, 3/4 LOCK NUT, 3/8 LOCK NUT...
Page 72
ASSEMBLY INSTRUCTIONS FRONT OF MACHINE 45° #8 O-RING-TUBE 45° #8 O-RING-TUBE ADAPTER ADAPTER TO TRACTOR NOTE: ATTACHMENT HOSES 3/4 O-RING CONNECT TO BOTTOM SET ADAPTER OF PORTS OF MANIFOLD RED HOSE WRAP 3/8 X 196 DETAIL A HOSE FRONT VIEW REAR VIEW 1/4 X 73 3/8 X 267...
Page 73
ASSEMBLY INSTRUCTIONS NOTE: USED ON NOTE: USED ON 45° #8 O-RING-TUBE FRONT OF MACHINE MODELS 2112-13/15 MODELS 2112-11 ADAPTER #8 O-RING TO TRACTOR TO #6 TUBE ADAPTER 45° #8 RED HOSE O-RING-TUBE WRAP ADAPTER 3/8 X 196 DETAIL A HOSE FRONT VIEW REAR VIEW REAR VIEW...
Page 74
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH MIDDLE PORTS OF FRONT MANIFOLD ASSEMBLY THEN ON HITCH HOSE LOOPS AND CLAMPS TO TRACTOR NOTE: RUN HOSES NOTE: RUN HOSES THROUGH SLOTTED THROUGH ALL HOSE NOTE: LOCATION OF HOLES OF ARMS CLAMPS AND LOOPS WRENCH MOUNT TO CYLINDER FITTINGS Figure 3-26: 3BCT/Chopper Hydraulic Layout 2112-09...
Page 75
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: LOCATION OF WRENCH NOTE: RUN HOSES MOUNT THROUGH SLOTTED NOTE: RUN HOSES THROUGH HOLES OF ARMS MIDDLE PORTS OF FRONT TO CYLINDER FITTINGS MANIFOLD ASSEMBLY THEN ON HITCH HOSE LOOPS AND CLAMPS TO TRACTOR Figure 3-27: 3BCT/Chopper Hydraulic Layout 2112-11-13-15 3-37...
ASSEMBLY INSTRUCTIONS Chopper Reel Installation 6. On hydraulic Chopper Reel option, install the 8 port manifold to manifold mount with 1/2 x 3-1/2 bolts, 1/2 (Option) lock nuts as shown See Figures 3-28. NOTE Refer to See Figures 2-34 through See Figures 2-43 for Standard Chopper Reel Placement.
Page 77
ASSEMBLY INSTRUCTIONS HOSE CLAMP, HOSE MOUNT PLATE, 3/8 X 1-1/2 BOLT, 1/2 X 8-1/2 BOLT, 3/8 FLAT WASHER, 1/2 FLAT WASHER 3/8 LOCK NUT 1/2 LOCK NUT HARROW EXTENSION LT RT, CHOPPER 3/4 X 7 BOLTS, ARM LONG 3/4 X 2-1/2 BOLTS, 3/4 LOCK NUT, NOTE: HOSE MOUNT ASSEMBLY USED ON 2112-09-11...
Page 78
ASSEMBLY INSTRUCTIONS FRONT OF MACHINE 45° #8 O-RING-TUBE 45° #8 O-RING-TUBE ADAPTER ADAPTER TO TRACTOR NOTE: ATTACHMENT HOSES 3/4 O-RING CONNECT TO BOTTOM SET ADAPTER OF PORTS OF MANIFOLD RED HOSE WRAP 3/8 X 196 DETAIL A HOSE FRONT VIEW REAR VIEW 1/4 X 51 3/8 X 267...
Page 79
ASSEMBLY INSTRUCTIONS NOTE: USED ON NOTE: USED ON 45° #8 O-RING-TUBE FRONT OF MACHINE MODELS 2112-13/15 MODELS 2112-11 ADAPTER #8 O-RING TO TRACTOR TO #6 TUBE ADAPTER 45° #8 RED HOSE O-RING-TUBE WRAP ADAPTER 3/8 X 196 DETAIL A HOSE FRONT VIEW REAR VIEW REAR VIEW...
Page 80
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH MIDDLE PORTS OF FRONT MANIFOLD ASSEMBLY THEN ON HITCH HOSE LOOPS AND CLAMPS TO TRACTOR NOTE: RUN HOSES NOTE: RUN HOSES THROUGH SLOTTED THROUGH ALL HOSE HOLES OF ARMS CLAMPS AND LOOPS TO CYLINDER FITTINGS Figure 3-32: Chopper Hydraulic Layout 2112-09 3-42 F-1102-0721...
Page 81
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS NOTE: RUN HOSES THROUGH SLOTTED NOTE: RUN HOSES THROUGH HOLES OF ARMS MIDDLE PORTS OF FRONT TO CYLINDER FITTINGS MANIFOLD ASSEMBLY THEN ON HITCH HOSE LOOPS AND CLAMPS TO TRACTOR Figure 3-33: Chopper Hydraulic Layout 2112-11-13-15 3-43...
Page 82
ASSEMBLY INSTRUCTIONS Rear Tow Hitch Installation 7. Mount 3/4 o-ring couplers, couplers mount, to back side of hyd hitch mount, using 3/8 x 1 bolts, 3/8 lock A rear tow hitch assembly is available for use on the rear nuts. Slide coupler dust plugs over front side of 3/4 of the Coulter Chisel.
Page 83
ASSEMBLY INSTRUCTIONS FRONT CLAMP PLATE 5/8 X 4-11/16 X 10-3/4 U-BOLT, 5/8 LOCK NUT 3/4 X 6-1/2 BOLT, 3/4 LOCK NUT HITCH TUBE WELDMENT 3/4 X 10 BOLT, TOW HITCH 3/4 LOCK NUT CLAMP PLATE 3/4 X 9-1/2 BOLT, 3/4 LOCK NUT HITCH MOUNT WELDMENT HITCH PLATE...
Page 84
ASSEMBLY INSTRUCTIONS FRONT BLACK HOSE WRAP HOSE ASSEMBLY COUPLER UNION HARNESS FITTING 34” EXT HITCH TUBE WELDMENT WING LOCK PIN, HARNESS 1/4 X 3 ROLL PIN, 96” EXT 3/16 DIA HAIR PIN DETAIL B PLASTIC TIE STRAP REAR HITCH WELDMENT, 3/4 X 2-1/2 BOLT, 3/4 LOCK NUT REAR JACK STAND,...
Page 85
ASSEMBLY INSTRUCTIONS NOTE: ROUTE HOSES THROUGH BLACK PLASTIC ALL HOSE LOOPS AND CLAMPS HOSE WRAP TIE STRAP ON CENTER FRAME AND HITCH ALONG LIFT AND FOLD HOSES TO TRACTOR COUPLER NOTE: ATTACH THE 4 PIN CONNECTOR OF TANDEM HARNESS ADAPTER HARNESS TO 34”...
ASSEMBLY INSTRUCTIONS 6. Inspect the final implement assembly, and verify that all bolts have been tightened, cotter pins spread, and that there are no leaking hydraulic connections. POUNDS 4 FOOT PULL CAUTION Tighten all 1-3/4” nuts to 1,250 foot-pounds of torque (See Figure 3-37)
Chapter 4 Operation and Maintenance DANGER DANGER Never allow anyone to ride on the 2112 coulter Always lock the tractor drawbar in the center chisel at any time. Allowing a person to ride on position when transporting the unit. Failure to do the machine can inflict serious personal injury or so can result in serious injury or death and cause death to that person.
OPERATION AND MAINTENANCE Tractor Preparation Attaching to the Tractor The 2112 Coulter Chisel is designed to be pulled by 1. Align the tractor drawbar with the machine. Raise or tractor equipped with a double lip or clevis type hitch. If lower the Coulter Chisel ring hitch, as needed, using your tractor is not equipped as such, you need to the swivel jack.
OPERATION AND MAINTENANCE Hydraulic Lift System 2 X 16 TRANSPORT LOCKOUT, L-PIN, WARNING 1/8” HAIRPIN, INSTALLED POSITION 2 X 16 TRANSPORT Escaping hydraulic fluid can cause serious LOCKOUT, L-PIN, personnel injury. Relieve system pressure before 1/8” HAIRPIN, repairing, adjusting, or disconnecting. wear STORED POSITION proper hand and eye protection when searching for leaks.
OPERATION AND MAINTENANCE Hydraulic Coulter Gang Lift General Operation System 1. The horsepower requirements are typically 20-25 horsepower per shank. This will vary widely due to The rephasing coulter gang lift system must be purged of speed, depth, moisture, residue and types of soils. air before beginning field operation.
OPERATION AND MAINTENANCE Field Operation Leveling (Front-to-Rear) 1. Raise the unit to take the weight off of the transport 1. The leveling feature on the 2112 Coulter Chisel is locks. Remove the transport locks from the lift used to keep the machine mostly level when raising cylinders (on both left and right sides).
OPERATION AND MAINTENANCE Variable Ratio Adjustment 1. To change the variable ratio adjustment, lower the implement to the ground and relieve the load on the The leveler is equipped with a variable ratio adjustment. lift system. Connect the leveler tube assembly to the middle hole in 2.
OPERATION AND MAINTENANCE Coulter Blades Depth Stop Adjustment 1. The 2112 Coulter Chisel is equipped with 22" coulter The operating depth of the 2112 Coulter Chisel is blades. controlled by a single-point depth stop. The stop is located at the center front of the machine. 2.
Seal kits are available from your b. Attach the safety chain to the tractor drawbar Landoll dealer. See Figure 4-6. Provide only enough slack in the 3. Check all hydraulic hoses weekly. Look for binding or chain for turning.
Page 95
OPERATION AND MAINTENANCE 4. Check that tires are of proper size, load rating, and inflated to manufacture specifications before 2 X 16 TRANSPORT transporting. Check wheel lug bolts to insure LOCKOUT, L-PIN, tightness. 1/8” HAIRPIN 5. Know the transport heights and widths of the unit before transporting.
OPERATION AND MAINTENANCE Wheel Bearing Maintenance – Wheel Bearing Maintenance -- Non Triple-Lip Triple-Lip Wheel bearing maintenance should be performed at the Transport tires use a self-contained seal with multiple beginning of every season of use. Check the wheel lips. The seal fits tight on both the spindle and wheel hub. bearings periodically for excessive end play.
OPERATION AND MAINTENANCE Lubrication Maintenance 3. Coulter gang bearings are equipped with triple-lip seals that will let grease pass and not harm the seal. Table 4-1 specifies the lubrication points and Regular lubrication will maintain a full grease cavity intervals on the 2112 Coulter Chisel. Proper and help purge any contaminants.
Page 98
OPERATION AND MAINTENANCE Figure 4-10: Lubrication Schedule LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Radius Rod Coulter Gang Bearings 1 each Walking Tandem Hubs 4 each Wheel Hubs 1 each Table 4-1: Lubrication Table 4-12 F-1102-0721...
Page 99
OPERATION AND MAINTENANCE Table provided for general use. NOTES: 4-13...
Electrocution can occur without aligned holes of harrow arm assemblies. direct contact. 6. Reels are set to 21-1/2” from Landoll. To adjust the standard reel height, loosen the locking hex nut 3. The coil tine harrow should run level with the coulter...
Page 101
OPERATION AND MAINTENANCE MORE LESS AGGRESSIVE AGGRESSIVE JAM NUT ANGLE HARROW HEIGHT ADJUSTMENT ADJUSTMENT HOLES SPRING PLATE ASSEMBLY 21-1/2 HARROW ARM ASSEMBLY REEL ASSEMBLY 1 X 7-5/16 PIN, 3/16 DIA HAIR PIN HARROW ADJUSTMENT 1/2 X 1-1/4 RD HEAD SQ NECK SCREW HARROW HEIGHT ADJUSTMENT...
OPERATION AND MAINTENANCE Chopper Reel Adjustments 3. Reels are set to 21-1/2” from Landoll. To adjust the reel height, loosen the locking hex nut against the 1. The optional chopper reel attachment consists of a threaded spring end See Figures 4-12.
Page 103
OPERATION AND MAINTENANCE SPRING JAM NUT ASSEMBLY 21-1/2" REEL ASSEMBLY REEL ASSEMBLY Figure 4-12: Chopper Reel Adjustments 4-17...
OPERATION AND MAINTENANCE Storage 2. Store the unit in a shed or under a tarpaulin to protect it from the weather. The ground tools and tires should 1. The service life of the 2112 Coulter Chisel will be rest on boards, or some other object, to keep them extended by proper off-season storage practices.
Chapter 5 Troubleshooting Guide PROBLEM PROBABLE CAUSE SOLUTION UNIT NOT PULLING EVEN Coulter gangs uneven depth Adjust depth/rephase coulter gang (See “Hydraulic Coulter cylinders Gang Lift System” on page 4-6.) (See “Leveling UNEVEN DEPTH Unit not level when under power in the field Level unit front to rear (Front-to-Rear)”...
Page 106
TROUBLESHOOTING GUIDE Table provided for general use. NOTES: F-1102-0721...
Page 107
Document Control Revision Log: Date Form # Improvement(s): Description and Comments 05/13/2021 F-1102 New Manual 06/22/2021 F-1102-0621 Initial Release 07/28/2021 F-1102-0721 Updated tire/wheel assembly...
Page 108
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 2112 Coulter Chisel Operator’s Manual Re-Order Part Number F-1102-0721 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...