1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. 2130
  6. Operator's manual

Landoll 2130 Operator's Manual

Wing coulter chisel
Hide thumbs
Table of Contents

Advertisement

Quick Links

MODEL 2130 WING COULTER CHISEL
OPERATOR'S MANUAL
1900 NORTH STREET
MARYSVILLE, KANSAS 66508
(785) 562-5381
F-488-0809
08/09

Advertisement

Table of Contents
loading

Related Manuals for Landoll 2130

Summary of Contents for Landoll 2130

  • Page 1 MODEL 2130 WING COULTER CHISEL OPERATOR’S MANUAL 1900 NORTH STREET MARYSVILLE, KANSAS 66508 (785) 562-5381 F-488-0809 08/09...
  • Page 3 MODEL 2130 WING COULTER CHISEL OPERATOR’S MANUAL PURCHASED FROM: DATE ADDRESS: PHONE NO.: SERIAL NO.:...
  • Page 4 NOTES:...

  • Page 5: Table Of Contents

    Table of Contents SECTION DESCRIPTION PAGE NO. INTRODUCTION ........1-1 STANDARD SPECIFICATIONS.
  • Page 6 SAFETY PRECAUTIONS THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY OR DEATH. DANGER DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUA- TION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

  • Page 7: Introduction

    INTRODUCTION The Landoll Model 2130 Wing Coulter Chisel is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation. SECTION 1 gives basic instructions on the use of this manual.
  • Page 8 NOTES:...

  • Page 9: Standard Specifications

    STANDARD SPECIFICATIONS 2130 SERIES COULTER CHISEL W/ AUTO RESET SHANKS 2130-17 21'-3" 16'-1" 11'-1" (8) 12.5L X 15, 19,888 Farm Highway Service 2130-19 23'-9" 16'-1" 11'-7" 20,830 F Load - 8 Bolt 2130-21 26'-3" 15'-6" 13'-5" 22,950 2130-23 28'-9" 15'-6"...
  • Page 10 LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION).
  • Page 11 LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL...
  • Page 12 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-17 shank-light placement Figure 2-1 Auto Reset Shank and Light Bracket Placement (2130-17)
  • Page 13 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-17_rsb shank-light placement Figure 2-2 Rigid Shear Shank and Light Bracket Placement (2130-17)
  • Page 14 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 4-7/8” 2130-19 shank-light placement Figure 2-3 Auto Reset Shank and Light Bracket Placement (2130-19)
  • Page 15 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5-1/8” 4-1/4” 4-1/4” 5” 5” 5” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 4-7/8” 2130-19_rsb shank-light placement Figure 2-4 Rigid Shear Shank and Light Bracket Placement (2130-19)
  • Page 16 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-21 shank-light placement p1 Figure 2-5 Auto Reset Shank and Light Bracket Placement (2130-21)
  • Page 17 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 2130-21 shank-light placement p2 Figure 2-6 Auto Reset Shank and Light Bracket Placement (2130-21)
  • Page 18 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 2130-21_rsb shank-light placement p1 Figure 2-7 Rigid Shear Shank and Light Bracket Placement (2130-21) 2-10...
  • Page 19 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 2130-21 shank-light placement p2 Figure 2-8 Rigid Shear Shank and Light Bracket Placement (2130-21) 2-11...
  • Page 20 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-23 shank-light placement p1 Figure 2-9 Auto Reset Shank and Light Bracket Placement (2130-23) 2-12...
  • Page 21 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” LT RT 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 4-7/8” 2130-23 shank-light placement p2 Figure 2-10 Auto Reset Shank and Light Bracket Placement (2130-23) 2-13...
  • Page 22 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-23_rsb shank-light placement p1 Figure 2-11 Rigid Shear Shank and Light Bracket Placement (2130-23) 2-14...
  • Page 23 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 4-7/8” 2130-23 shank-light placement p2 Figure 2-12 Rigid Shear Shank and Light Bracket Placement (2130-23) 2-15...
  • Page 24 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5” 5-1/8” 5-1/8” 5-1/8” 4-1/4” 5” 4-3/4” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 4-7/8” 2130-25_rsb shank-light placement p1 Figure 2-13 Rigid Shear Shank and Light Bracket Placement (2130-25) 2-16...
  • Page 25 NOTE: LT AND RT INDICATES THE RECOMMENDED PLACEMENT FOR TWISTED SHOVELS. 5-1/8” 5” 5-1/8” 5-1/8” 4-1/4” 5” 4-3/4” 20-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/8” 5-1/2” 4-7/8” 2130-25 _rsb shank light placement p2 Figure 2-14 Rigid Shear Shank and Light Bracket Placement (2130-25) 2-17...
  • Page 26 82” REEL/GANG BAR ASSEMBLY 82” REEL/GANG BAR ASSEMBLY 114” REEL/GANG BAR ASSEMBLY 12-1/4” 20-1/2” 12-1/4” 19-1/2” 30” 51-1/2” 51-1/2” 30” 19-1/2” 2130-17 91” REEL/GANG BAR ASSEMBLY 91” REEL/GANG BAR ASSEMBLY 114” REEL/GANG BAR ASSEMBLY 21” 21” 11-1/8” 11-1/8” 30” 30” 52” 52”...
  • Page 27 19” 24” 30” 30” 51-1/2” 51-1/2” 30” 30” 24” 16-1/4” 12-1/4” 12-1/4” 16-1/4” 2130-23 19-7/8” 55” REEL/GANG BAR 55” REEL/GANG BAR 114” REEL/GANG BAR ASSEMBLY ASSEMBLY ASSEMBLY 91” REEL/GANG BAR ASSEMBLY 91” REEL/GANG BAR ASSEMBLY 28-1/4” 28-1/4” 30” 30” 51-1/2”...
  • Page 28 NOTE: AUTO RESET SHANK SHOWN. CHOPPER REELS ATTACH TO RIGID SHEAR SHANK MODELS USING SAME DIMENSIONS. 3-1/2 11-1/2 26-1/2 11-1/2 2130-17 38-1/2 3-1/2 12-1/2 25-1/4 12-1/2 2130-19 2130-17 & 19 chopper reel placement Figure 2-17 Tubular Mount Chopper Reel Placement (2130-17 & 2130-19) 2-20...
  • Page 29 NOTE: AUTO RESET SHANK SHOWN. CHOPPER REELS ATTACH TO RIGID SHEAR SHANK MODELS USING SAME DIMENSIONS. 11-1/2 11-1/2 3-1/2 26-1/4 2130-21 3-1/2 11-1/2 11-1/2 3-1/2 39-1/2 39-1/2 26-1/2 2130-23 2130-21-23 chopper reel placement Figure 2-18 Tubular Mount Chopper Reel Placement (2130-21 & 2130-23) 2-21...
  • Page 30 NOTE: RIGID SHEAR SHANK MODEL SHOWN. CHOPPER REELS ATTACH TO AUTO RESET SHANK MODELS USING SAME DIMENSIONS. 5-1/2 5-1/2 3-1/2 3-1/2 12-1/2 12-1/2 19-1/2 2130-25 2130-25 chopper reel placement Figure 2-19 Tubular Mount Chopper Reel Placement (2130-25) 2-22...

  • Page 31: Assembly Instructions

    ASSEMBLY INSTRUCTIONS WARNING It is very important that your new 2130 Wing Coulter Chisel be properly assembled, adjusted and lubricated before use. Illustrations to assist with the DO NOT ATTEMPT TO LIFT HEAVY assembly process are provided in Section 2, PARTS (SUCH AS THE FRAME, COUL- “Standard Specifications”.
  • Page 32 1-8 HEX LOCK NUT 1-1/2 FLANGE BEARING LEVELER TUBE 1-1/4N FLAT WASHER HITCH PIN 1-8 HEX LOCK NUT 1/2 X 2-1/4 GROOVED ALLOY PIN 1-1/4 - 7 HEX NUT 1-1/4 - 7 HEX NUT 1-1/4 SLOTTED LOCK WASHER 1-1/4 SLOTTED LOCK WASHER HITCH RADIUS FRAME...

  • Page 33: Wing Coulter Chisel Center Frame Assembly

    3-1 WING COULTER CHISEL CENTER FRAME ASSEMBLY IMPORTANT WARNING READ ALL SAFETY PRECAUTIONS AT THE FRONT OF THE SECTION BEFORE ATTEMPT- DO NOT ATTEMPT TO LIFT HEAVY ING ANY OF THE FOLLOWING PROCE- PARTS ( SUCH AS THE FRAME, DURES. COULTER GANGS, WHEEL LIFT, AND 3-1.1 Place center frame assembly on stands...

  • Page 34: Depth Stop Tube Assembly

    5/8-11 HEX LOCK NUT DEPTH STOP TUBE ASSEMBLY DEPTH STOP MOUNT PLATE 3/8-16 X 1-1/4 HEX HEAD 5/8-11 HEX NUT CAP SCREW 5/8-11 X 3 HEX 5/16-18 X 4 HEX HEAD CAP HEAD CAP SCREW SCREW SHANK LIFT DEPTH STOP PLATE DEPTH STOP...
  • Page 35 3-3 DEPTH STOP TUBE ASSEMBLY 3-3.1 Attach the depth stop mount plate to the 3-3.4 Using 5/16-18 x 4 hex head cap screws shank lift using 3/8-16 x 1-1/4 hex head cap secure the front end of the depth stop tube screws and hex lock nuts.
  • Page 36 5-16 x 2-1/2 SPRING SLOTTED PIN 4 X 30 HYDRAULIC FOLD PIN CYLINDER REAR FOLD ANCHOR FRONT FOLD ANCHOR (USED ON ALL (USED ON 2130-21, MODELS) 2130-23, AND 2130-25 MODELS ONLY) 5/8-11 HEX LOCK NUT U-BOLT 4 X 30 HYDRAULIC CYLINDER...

  • Page 37: Center Frame Tires

    3-5.1 For 17 and 19 shank models, assemble 3-5.4 On the 2130-21, 2130-23, and 2130-25 the fold anchor to the rear cross bar using models, attach the bolt-on hinges to the right and left sides of the center frame using u-bolts and 5/8-11 hex lock nuts (See Figure 3-3).
  • Page 38 RIGHT WING FRAME ASSEMBLY 4 X 16 SLAVE 1 HYDRAULIC CYLINDER 90 ADAPTERS 1/2 X 2-1/4 GROOVED ALLOY PIN HITCH PIN 1-1/2 THRUST WASHER (INSTALL TO FRONT SIDE) 1-8 HEX LOCK NUTS 5/16 X 2-1/2 SPRING SLOTTED PIN FOLD PIN 4 X 30 HYDRAULIC CYLINDER 3/16 HAIR PIN CENTER FRAME ASSEMBLY...

  • Page 39: Wing Frame Installation

    Install 4-1/2 x 16 hydraulic cylinders to POSITION. the cylinder anchor plates of the center 3-6.1 On 2130-17 and 2130-19 models, attach frame assembly using roll pins and clevis right and left wing frame assemblies to the pins supplied with the cylinder.
  • Page 40 CYLINDER 4 X 8 MASTER HYDRAULIC LEFT CENTER CYLINDER COULTER GANG LEFT WING ASSEMBLY COULTER GANG ASSEMBLY SHANK PIN 1-8 HEX LOCK NUT 1/2 X 2-1/4 GROOVED ALLOY PIN 2130 coulter gang assembly op Figure 3-5 Coulter Gang Installation 3-10...

  • Page 41: Coulter Gang Installation

    3-7 COULTER GANG INSTALLATION DANGER 3-7.2 Attach the base end of the 4 x 8 master cylinder to the coulter spring rod assembly attached to the left wing frame weldment us- COULTER BLADES ARE EXTREMELY ing the clevis pins and roll pins which come SHARP.
  • Page 42 CLAMP ASSEMBLY 3/4-10 HEX LOCK NUT 1-1/4 X 2-1/2 X 32 50 SHANK 3/4-10 X 4 HEX HEAD CAP SCREW 2 X 1 X 18 SPIKE 1/2-13 X 3 HEX HEAD CAP SCREW 1/2 HEAVY HEX NUT NOTE: 1/2 X 4 X 26 TWISTED SHOVEL OPTION NOT SHOWN.

  • Page 43: Auto Reset Shank And Shovel Installation

    3-8 AUTO RESET SHANK AND SHOVEL INSTALLATION b. Connect 1/2 x 4 x 26 twisted shovels to 3-8.1 Install 2 x 1 x 18 spikes or 1/2 x 4 x 26 each shank using 1/2-13 x 3 plow bolts, flat twisted shovels onto shanks as follows: washers, and heavy hex nuts.
  • Page 44 SHEAR BOLT CLAMP 12” OFFSET SHEAR BOLT CLAMP 5/8-11 HEX LOCK NUT 3/4-10 HEX LOCK NUT 1-1/4 X 2-1/2 X 32 50 SHANK 5/8-11 X 5 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW 2 X 1 X 18 SPIKE 1/2-13 X 3 HEX HEAD CAP SCREW...

  • Page 45: Rigid Shear Shank And Shovel Installation

    5/8 X 3/4 X 1-1/4 CONNEX BUSHINGS SHOWN washer (in bottom hole only), split lock wash- IN THE DRAWING ARE INSTALLED AT THE ers, and hex nuts. See Figures 2-1 - 2-14 LANDOLL CORPORATION. for recommended locations of right hand and left hand shovels. IMPORTANT...
  • Page 46 8 PORT MANIFOLD (USED ON ALL MODELS) 1/2-13 X 3-1/2 HEX HEAD CAP SCREW 8 PORT MANIFOLD (USED ON 2130-21, 2130-23, AND 2130-25 MODELS ONLY) 16 PORT MANIFOLD (USED ON ALL MODELS) hydraulic manifold placement Figure 3-8 Hydraulic Manifold Placement...

  • Page 47: Hydraulic Installation

    Install plugs in any remaining open screws and hex lock nuts (See Figure 3-8). manifold or valve ports. 3-10.3 On 2130-21, 2130-23, and 2130-25 3-10.10 Install hose wraps around system models, install second 8 port manifold to the hoses per hose identification decal near...
  • Page 48 3/8 X 96 HOSE ASSEMBLY 90 ADAPTER 3-1/4 X 8 REPHASE HYDRAULIC CYLINDER 3/8 X 276 HOSE ASSEMBLY SLAVE 3 90 ADAPTER 90 ELBOW W/ RESTRICTOR 2130 17-19 coulters op Figure 3-10 Coulter Lift Hydraulic Installation (2130-17 & 2130-19) 3-18...
  • Page 49 3/8 X 120 HOSE ASSEMBLY 90 ADAPTER 3-1/4 X 8 REPHASE HYDRAULIC CYLINDER 3/8 X 6 HOSE ASSEMBLY SLAVE 3 90 ADAPTER 90 ELBOW W/ RESTRICTOR 2130 21-25 coulters op Figure 3-11 Coulter Lift Hydraulic Installation (2130-21, 2130-23, & 2130-25) 3-19...
  • Page 50 MASTER DECAL 90 ADAPTER 4 X 16 REPHASE HYDRAULIC 3/8 X 120 HOSE CYLINDER ASSEMBLY SLAVE 90 ADAPTER SLAVE DECAL FRONT ADAPTER OF MACHINE PLUG PORTS B,G,H,K,L,&M 2130 17-19 lift op Figure 3-12 Wheel Lift Hydraulic Installation (2130-17 & 2130-19) 3-20...
  • Page 51 90 ADAPTER 4 X 16 REPHASE HYDRAULIC 3/8 X 146 HOSE CYLINDER ASSEMBLY SLAVE 90 ADAPTER SLAVE DECAL FRONT ADAPTER OF MACHINE PLUG PORTS B,G,H,K,L,&M 2130 21-25 lift op Figure 3-13 Wheel Lift Hydraulic Installation (2130-21, 2130-23, & 2130-25) 3-21...
  • Page 52 3/8 X 24 HOSE FOLD PIN ASSEMBLY 1-1/4N FLAT WASHER 90 ELBOW W/ RESTRICTOR 5/16 X 2-1/2 SPRING SLOTTED PIN FRONT OF MACHINE PLUG PORTS E & F 2130 17-19 fold hyd Figure 3-14 Fold Hydraulic Installation (2130-17 & 2130-19) 3-22...
  • Page 53 3/8 X 24 HOSE 90 ELBOW W/ ASSEMBLY RESTRICTOR FOLD PIN 4 X 30 HYDRAULIC 1-1/4N FLAT CYLINDER WASHER 5/16 X 2-1/2 SPRING SLOTTED PIN FRONT OF MACHINE 2130 21-25 fold hyd Figure 3-15 Fold Hydraulic Installation (2130-21, 2130-23, & 2130-25) 3-23...
  • Page 54 MAIN WARNING LIGHT HARNESS REAR WARNING LIGHT HARNESS ORANGE STRIPE YELLOW REFLECTOR LH LIGHT BRACKET (FRONT OF BRACKET) 1/2-13 X 8-1/2 HEX #8-32 X 1/2 SLOT HEAD CAP SCREW PAN HEAD SCREW 1/4-20 X 1-1/4 HEX ENHANCED HEAD CAP SCREW LIGHTING MODULE 1/4-20 HEX LOCK...

  • Page 55: Light Installation

    3-11 LIGHT INSTALLATION IMPORTANT Note: See Figures 2-1 - 2-14 for light bracket placement. If no dimension is given for a OUTER LIGHT BRACKETS NEED TO BE SLID bracket, it should be located against frame REARWARD AS FAR AS POSSIBLE. SEE FIG- member as shown in drawing.

  • Page 56: Final Assembly

    3-12 FINAL ASSEMBLY 3-12.1 Attach a tractor to the implement and 3-12.4 Connect lights to the tractor and verify charge the lift system hydraulics as de- operation. scribed is Section 4-4. 3-12.5 Check tires for proper inflation 3-12.2 Install the 2 x 16 transport lockouts on 3-12.6 Level the Wing Coulter Chisel from front both 4-1/2 x 16 master cylinders on the cen-...

  • Page 57: Offset Shank Mount Installation (Option)

    3-13 OFFSET SHANK MOUNT INSTALLATION (OPTION) If back row of shanks continually plug with res- idue, offset shank mounts are available for the back row of shanks. Contact the Landoll Corpora- 3/4-10 HEX LOCK NUT tion Service department for more information.
  • Page 58 7-3/4” REAR TOW HITCH - SHORT ARM 11-3/4” REAR TOW HITCH - LONG ARM 2130 rear tow hitch placement Figure 3-19 Rear Tow Hitch Placement (Option) 3-28...

  • Page 59: Rear Tow Hitch Installation (Option)

    5/8-11 X 9-1/2 HEX HEAD CAP SCREW GR5 REAR HITCH ARM REAR TOW HITCH ASSEMBLY REAR HITCH ARM W/ HOSE LOOPS 5/8-11 HEX LOCK NUT GRB 3/4-10 HEX LOCK NUT GRB REAR HITCH CLAMP PLATE 3/4-10 X 2-1/2 HEX HEAD CAP SCREW m148332 op Figure 3-20 Rear Tow Hitch Installation (Option) 3-14 REAR TOW HITCH INSTALLATION (OPTION)

  • Page 60: U-Bolt Mount Chopper Reel Installation (Option)

    5/8-11 X 6-11/16 X 5-1/2 U-BOLT REAR BAR OF FRAME OR WING ASSEMBLY 5/8-11 HEX LOCK NUT LONG REEL ARM ASSEMBLY 5/8-11 HEX LOCK NUT 5/8-11 X 3-11/16 X 4-5/8 U-BOLT SHORT REEL ARM ASSEMBLY REEL/GANG BAR ASSEMBLY chopper reel assy op Figure 3-21 U-Bolt Mount Chopper Reel Installation (Option) 3-15 U-BOLT MOUNT CHOPPER REEL INSTALLATION (OPTION) 3-15.1...

  • Page 61: Tubular Mount Chopper Reel Installation (Option)

    3/4-10 X 12 HEX HEAD CAP SCREW REAR BAR OF FRAME SUPPORT OR WING ASSEMBLY PLATE CHOPPER REEL ARM ASSEMBLY SUPPORT PLATE 3/4-10 HEX LOCK NUT 5/8-11 HEX LOCK NUT GANG BAR MOUNT PLATE REEL/GANG BAR ASSEMBLY 5/8-11 X 5 HEX HEAD CAP SCREW ar and rsb chopper reel assy op...
  • Page 62 NOTES: 3-32...

  • Page 63: Operation And Maintenance

    DANGER DANGER NEVER ALLOW ANYONE TO RIDE ON ALWAYS LOCK THE TRACTOR DRAW- THE 2130 WING COULTER CHISEL AT BAR IN THE CENTER POSITION WHEN ANY TIME. ALLOWING A PERSON TO TRANSPORTING THE UNIT. FAILURE RIDE ON THE MACHINE CAN INFLICT...

  • Page 64: Tractor Preparation

    4-1 TRACTOR PREPARATION The Landoll 2130 Wing Coulter Chisel is de- 4-1.1 Inflate the rear tractor tires equally and signed to be pulled by tractor equipped with a dou- add ballast according to the tractor opera- ble lip or clevis type hitch. If your tractor is not tor’s manual.
  • Page 65 This will keep all cylinders in time and frame sections level when operating. 2 X 16 TRANSPORT 2 X 16 TRANSPORT LOCKOUT LOCKOUT L PIN L PIN 1/8 HAIR PIN 2130-translockoff 2130-translockon Figure 4-2 Installed Transport Locks Figure 4-3 Stored Transport Locks...

  • Page 66: Hydraulic Fold System

    4-5 HYDRAULIC FOLD SYSTEM 4-5.1 2130 Wing Coulter Chisel 4-5.3 To charge the system, carefully hitch equipped with a hydraulic fold system to the coulter chisel to the tractor. Unpin the raise and lower the wing frames for narrow end(s) of the fold cylinders, and position transport.
  • Page 67 4-5.5 To fold/unfold the 2130 Wing Coulter WING STABILIZER Chisel, find a level area large enough to ac- BRACKET commodate the implement when it is fully un- folded. The tractor should be stopped and not moving with the unit fully raised.

  • Page 68: Hydraulic Coulter Gang Lift System

    4-6 HYDRAULIC COULTER GANG LIFT SYSTEM IMPORTANT The rephasing coulter gang lift system must be purged of air before beginning field operation. To WHEN INITIALLY FILLING THE CYLINDERS insure that all air is purged from the system, the WITH OIL OR AFTER EXTENDED PERIODS gang cylinders are mounted in a vertical position OF STORAGE, HOLD THE TRACTOR VALVE with the base end of each cylinder mounted on the...

  • Page 69: Field Operation

    (See Figure 4-5). 4-9 LEVELING (FRONT-TO-REAR) 4-9.1 The leveling feature on the 2130 Wing ADJUSTMENT Coulter Chisel is used to keep the machine WRENCHES level when raising the unit from a working position to a transport position.

  • Page 70: Leveling (Side To Side)

    4-10 LEVELING (SIDE TO SIDE) 4-10.1 Leveling the 2130 Wing Coulter Chisel side-to-side involves leveling the wing frame to the center frame. The unit should be level side-to-side when operating in the field. 4-10.2 To level the unit, verify that all tires are properly inflated.
  • Page 71 4-10.3 An adjusting wrench is provided to 4 X 16 HYDRAULIC BASE END make this adjustment. It may be necessary CYLINDER ADJUSTMENT to lower the wing to the ground and relieve weight on the cylinder anchor to make this adjustment. If required, fully raise the imple- ment, lower to just above the ground, and re-verify measurements.

  • Page 72: Variable Ratio Adjustment

    4-11 VARIABLE RATIO ADJUSTMENT The leveler is also equipped with a variable ra- tio adjustment. This is located at the rear of the LEVELER TUBE hitch. Connect the leveler tower to the top holes in the hitch for normal operations. The lower holes on LEVELER TOWER the hitch are for a reduced leveler ratio.

  • Page 73: Coulter Blades

    4-12 COULTER BLADES DANGER 4-12.1 The 2130 Wing Coulter Chisel is equipped with 22" coulter blades. COULTER BLADES ARE EXTREMELY 4-12.2 The 22” diameter blades are flat with a SHARP. EXERCISE EXTREME CARE thickness of 4 ga (.256”) and are standard WHEN WORKING ON OR NEAR COUL- for the 2130 Wing Coulter Chisel.

  • Page 74: Depth Stop Adjustment (Manual)

    4-13 DEPTH STOP ADJUSTMENT (MANUAL) The operating depth of the 2130 Wing Coulter Chisel is controlled by a single-point depth stop. DEPTH STOP TUBE The stop is located at the center front of the ma- chine. DEPTH STOP GAUGE 4-13.1...

  • Page 75: Hydraulic Maintenance

    Check and follow all federal, state, and local requirements before transporting the Coulter Chisel. 4-16.2 The 2130 Wing Coulter Chisel should HITCH WELDMENT be transported only by tractor required for field operation. The implement weight should not exceed more than 1.5 times the tractor weight.
  • Page 76 Make sure lights, reflectors and SMV emblem are clearly visible and operat- ing. Remove any obstructions such as dirt, mud, stalks or residue that restricts view be- fore transporting. 2130-translockon Figure 4-12 Installed Transport Locks 4-14...
  • Page 77 2130 lube Figure 4-13 Lubrication Schedule LUBRICATION TABLE ITEM DESCRIPTION NO. OF LUBE POINTS INTERVAL (Hours unless stated) Coulter Gang Bearings 1 each Radius Rod Walking Tandem Hubs 1 each Wheel Hubs 1 each Table 4-3 Lubrication Table 4-15...

  • Page 78: Lubrication Maintenance

    4-18 STORAGE e. Apply a light coating of oil or grease to ex- 4-18.1 The service life of the 2130 Wing Coul- posed cylinder rods to prevent them from ter Chisel will be extended by proper off-sea- rusting. son storage practices. Prior to storing the f.
  • Page 79 NOTES 4-17...

  • Page 81: Troubleshooting Guide

    TROUBLESHOOTING GUIDE The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can hap- pen using your 2130 Wing Coulter Chisel. Follow all safety precautions stated in the previous sections when making any adjustments to your machine.
  • Page 82 BACK ROW OF SHANKS PLUGGING WITH Heavy residue: install optional offset shank mounts RESIDUE to stagger back row of shanks. See "Offset Shank Mount Installation" on page 3-27. SHANKS NOT PENETRATING Unit not level: level unit front to rear. See "Leveling (Front To Rear)"...
  • Page 83 NOTES:...

Table of Contents