1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. 2210
  6. Operator's manual

Landoll 2210 Series Operator's Manual

Weatherproofer
Hide thumbs Also See for 2210 Series:
Table of Contents

Advertisement

Quick Links

MODEL 2210 SERIES
WEATHERPROOFER
OPERATOR'S MANUAL
1900 NORTH STREET
MARYSVILLE, KANSAS 66508
(785) 562-5381
F-227-896
8/96

Advertisement

Table of Contents
loading

Related Manuals for Landoll 2210 Series

Summary of Contents for Landoll 2210 Series

  • Page 1 MODEL 2210 SERIES WEATHERPROOFER OPERATOR’S MANUAL 1900 NORTH STREET MARYSVILLE, KANSAS 66508 (785) 562-5381 F-227-896 8/96...
  • Page 2 LANDOLL will not be liable for labor, transpor- tation, or any other charges resulting from replacement of a defective part. This warranty is void if any part not supplied by LANDOLL is used in assembly or repair, or if the machine has been altered, abused, or neglected.
  • Page 3 MODEL 2210 SERIES WEATHERPROOFER OPERATOR’S MANUAL PURCHASED FROM: DATE ADDRESS: PHONE NO.: SERIAL NO.:...

  • Page 4: Table Of Contents

    TRACTOR PREPARATION ......4-4 MODEL 2210 SERIES WEATHERPROOFER PREPARATION ..4-4 ATTACHING TO THE TRACTOR .
  • Page 5 SAFETY PRECAUTIONS THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY OR DEATH. DANGER DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUA- TION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

  • Page 7: Introduction

    INTRODUCTION The Landoll 2210 Series Weatherproofer is a quality product designed to give years of trouble free per- formance. By following each section of this manual, your system will perform as designed for you and your operation. SECTION 1 gives basic instructions on the use of this manual.

  • Page 9: Standard Specifications

    STANDARD SPECIFICATIONS SPECIFICATIONS Model Working Transport Number Number Shank Weight Number Width Width Shanks Discs Spacing (Approx. (ft.-in.) (ft.-in.) (in.) lbs) 2215-3-30 5200 2215-4-24 5400 2215-4-30 10-0 11-4 5600 2215-5-24 10-0 11-4 5800 2215-5-30 12-6 13-8 6400 2215-6-30 12-6 16-0 6900 2217-5-30 12-6...
  • Page 10 LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION).
  • Page 11 LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL...
  • Page 12 NOTES:...
  • Page 13 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-1 2215-3-30 Shank Disc Spacing...
  • Page 14 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-2 2215-4-24 Shank Disc Spacing...
  • Page 15 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-3 2215-4-30 Shank Disc Spacing...
  • Page 16 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-4 2215-5-24 Shank Disc Spacing...
  • Page 17 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-5 2215-5-30 Shank Disc Spacing...
  • Page 18 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-6 2215-6-30 Shank Disc Spacing 2-10...
  • Page 19 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-7 2217-5-30 Shank Disc Spacing 2-11...
  • Page 20 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-8 2217-6-30 Shank Disc Spacing 2-12...
  • Page 21 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-9 2217-7-24 Shank Disc Spacing 2-13...
  • Page 22 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-10 2217-7-30 Shank Disc Spacing 2-14...
  • Page 23 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-11 2217-8-30 Shank Disc Spacing 2-15...
  • Page 24 NOTE: DISC GANG ANGLE SHOWN IS 20 Figure 2-12 2217-9-24 Shank Disc Spacing 2-16...

  • Page 25: Assembly Procedures

    ASSEMBLY PROCEDURES WARNING It is very important that your new 2210 Series Weatherproofer be properly assembled, adjusted, and lubricated before use. Illustrations to assist DO NOT ATTEMPT TO LIFT HEAVY with the assembly process are provided in Section PARTS (SUCH AS THE FRAME, DISC 2, “Standard Specifications”.
  • Page 26 Figure 3-1 2217 Frame Assembly...

  • Page 27: 2215 Frame Assembly

    Paragraph 3-2.4 and 3-2.5 for their proper in- However, it needs to be placed on stands about stallation procedures. Paragraph 3-2.6 describes 36" high in an open, level area. If your 2210 Series proper installation of tool boxes. 3-2 2217 FRAME ASSEMBLY...
  • Page 28 Figure 3-2 2215 Rockshaft Installation Figure 3-3 2215 Gauge Wheel Cylinder Installation...

  • Page 29: 2215 Rockshaft Installation

    3-3 2215 ROCKSHAFT INSTALLATION IMPORTANT 3-3.4 Secure each set of bearings tight enough to the rockshaft to hold the assembly to- READ ALL SAFETY PRECAUTIONS AT THE gether. Use the washers and locking nuts FRONT OF THE SECTION BEFORE ATTEMPT- provided.
  • Page 30 Figure 3-4 2217 Rockshaft Installation Figure 3-5 2217 Gauge Wheel Cylinder Installation...

  • Page 31: 2217 Rockshaft Installation

    3-4 2217 ROCKSHAFT INSTALLATION IMPORTANT 3-4.5 Insert the rockshaft shims, as needed, be- tween each set of bearings. Use the shims READ ALL SAFETY PRECAUTIONS AT THE to allow the rockshaft to rotate freely, yet not FRONT OF THE SECTION BEFORE ATTEMPT- loosely, in the bearing halves.
  • Page 32 Figure 3-6 Hydraulic Hose Installation 2215/2217 HYDRAULIC HOSE ITEM MODEL 2215 DESCRIPTION MODEL 2217 DESCRIPTION PART PART NUMBER NUMBER 1-397-010300-04 HOSE 275" 1-397-010300-10 HOSE 324" 1-397-010299-10 HOSE 50" 1-397-010088 HOSE 84" 1-397-010299-01 HOSE 60" 1-397-010071 HOSE 94" 1-397-010104 HOSE 41" 1-397-010299-13 HOSE 74"...

  • Page 33: Gauge Wheel Hydraulic Plumbing Installation

    3-5 GAUGE WHEEL HYDRAULIC PLUMBING INSTALLATION Install a 90 o restrictor fitting to the base 3-5.4 IMPORTANT end ports of both cylinders. 1. Pipe sealant is not required to install hoses CAUTION to manifold and cylinders equipped with hy- draulic O-ring fittings. IMPROPER INSTALLATION OF RE- 2.
  • Page 34 Figure 3-7 Pull Hitch Installation 3-10...

  • Page 35: Pull Hitch Installation

    3-6 PULL HITCH INSTALLATION CAUTION IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE INSTALL LEVELING ROD SO THAT FRONT OF THIS SECTION BEFORE ATTEMPT- KEEPER HOLE ON CLEVIS IS ON ING ANY OF THE FOLLOWING PROCEDURES. RIGHT SIDE OF MACHINE. THIS GIVES IMPORTANT THE MOST CLEARANCE BETWEEN THE MAST AND CLEVIS.
  • Page 36 Figure 3-8 Rigid Riser Disc Gang Installation 3-12...

  • Page 37: Standard Rigid Riser Disc Gang Installation

    3-7 STANDARD RIGID RISER DISC GANG INSTALLATION DANGER IMPORTANT THE FRONT AND REAR DISC GANG TUBES D IS C BL A DE S AR E E X TRE M E LY ARE THE SAME LENGTH FOR THE 4-BLADE SHARP. EXERCISE EXTREME CARE DISC GANGS ON THE 2215’S AND FOR THE 6- WHEN WORKING ON OR NEAR DISC BLADE DISC GANGS ON THE 2217’S.
  • Page 38 Figure 3-9 Flex Disc Gang Installation 3-14...

  • Page 39: Flex Disc Gang Installation

    3-8 FLEX DISC GANG INSTALLATION DANGER IMPORTANT THE FRONT AND REAR DISC GANG TUBES D IS C BL A DE S AR E E X TRE M E LY ARE THE SAME LENGTH FOR 4-BLADE DISC SHARP. EXERCISE EXTREME CARE GANGS (ON 2215’S) AND 6-BLADE DISC WHEN WORKING ON OR NEAR DISC GANGS (ON THE 2217’S).
  • Page 40 Figure 3-10 Spring Shank Installation 3-16...
  • Page 41 3-9 SPRING SHANK INSTALLATION DANGER 3-9.3 Install spikes on shanks using a roll pin. If installing wearguards, seat spike on shank. Then install wearguard into slot and clamp in D IS C BL A DE S AR E E X TRE M E LY place with wearguard clamp without unseat- SHARP.

  • Page 42: Lubrication

    3-10 LUBRICATION The 2210 Series Weatherproofer must be lubri- cated before using it for the first time, and at regu- lar intervals thereafter. Use a standard multi- purpose grease and the Lubrication Chart (See Paragraph 4-6 and Figure 4-2 “WEATHER- PROOFER LUBRICATION SCHEDULE”) to lubri-...

  • Page 43: Operation And Maintenance

    OPERATION AND MAINTENANCE DANGER WARNING D IS C BL A DE S AR E E X TRE M E LY WHEN TRANSPORTING THE UNIT, SHARP. EXERCISE EXTREME CARE FULLY EXTEND THE CYLINDERS AND WHEN WORKING ON OR NEAR DISC PLACE CYLINDER LOCKOUTS IN THE BLADES.

  • Page 44: Tractor Preparation

    Before attaching the Weatherproofer, prepare the tractor as follows: 4-2 MODEL 2210 SERIES WEATHERPROOFER PREPARATION CAUTION 4-2.1 Prior to operating the Model 2210 Series Weatherproofer, inspect it thoroughly for good operating condition. WHEN ADJUSTING DISC SCRAPER, 4-2.2 Replace worn or missing parts.
  • Page 45 Figure 4-2 2210 Series Lubrication Schedule...

  • Page 46: Attaching To The Tractor

    Lower to the ground when the control lever 4-3.1 Align the tractor drawbar with the machine. is moved forward or downward, and Raise or lower the Model 2210 Series b. Raise when the control lever is moved back- Weatherproofer clevis, as needed, using the ward or upward.
  • Page 47 Figure 4-4 2210 Series Spacer Block Placement...

  • Page 48: Wheel Bearing Maintenance

    Install a new cotter pin and replace the or defective parts. hub cap. 4-6 LUBRICATION Several parts of the Model 2210 Series Weath- erproofer need periodic lubrication. Use of a high grade multi-purpose is recommended. Refer to the Weatherproofer Lubrication Chart (See Figure 4-2) to locate lubrication points and for a recommended maintenance schedule.

  • Page 49: Hydraulic Maintenance

    4-8 STORAGE d. Grease or coat all exposed metal surfaces 4-8.1 The service life of the 2210 Series Weath- of shanks, points, and coulters. erproofer will be extended by proper off- e. Lubricate each point of the machine as season storage practices.
  • Page 50 NOTES:...

  • Page 51: Troubleshooting Guide

    TROUBLESHOOTING GUIDE The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2210 Series Weatherproofer. Follow all safety precautions stated in the previous when making any adjustments to your machine. SYMPTOM PROBLEM: REMEDY...
  • Page 52 NOTES:...

This manual is also suitable for:

2215-3-302215-4-242215-4-302215-5-242215-5-302215-6-30 ... Show all

Table of Contents